Arx Valdex BCR6100 Installation instructions

BCR6100
6 in 1 Card Reader BAY

2
? ?DESCRIPTION:
The BCR6100 is USB 1.1 6-in-1 Card Reader.
? ?Check your packing listing:
BCR6100 x 1
Hardware Guide x 1
** If any of these items are missing from the BCR6100 Retail package, contact your
supplier immediately.
? ?Hardware Specification
??USB 1.1 Interface
??One Reader works with multiple media -CompactFlash, IBM Microdrive,
SmartMedia, MultiMediaCards, SD Cards, and Memory Stick Looks like
removable disk drive -drag and drop files between the digital media
cards and the computer
??No additional power supply needed -bus powered device
??Transfer more data in less time -faster upload/downloads
??Support Windows 98/SE, Windows ME, Windows NT, Windows 2000,
Windows XP and Linux.

3
? ?Attaching to5.25 inch Bay :
1. Make sure your computer is powered off. Then attach the BCR6100 to 5.25 inch bay.
Attach cable for adapter connection to the front-bay extension adapter, as shown below.
2. Insert the BCR6100 into 5.25 inch bay and fix it, as shown below.
3. Connect the USB cable to the PCI USB adapter.
4. Install the USB adapter into the PCI slot. Press down firmly until the card clicks into place.
Then, screw down the bracket of the USB adapter, as shown below.
5. Then finished.
Power cable for
adapter connection

4
? ?Card Reader Installation:
Windows 98/SE
1. Insert the Driver CD into the CD-ROM drive.
2. Click the CD-ROM drive icon and find the "Card Reader" folder.
3. Find "setup.exe" and double click it.
4. Follow the setup of "Install Wizard" to install the "USB Card Reader Driver".
5. Plug Card Reader into USB port and Windows 98 will detect it automatically.
6. The pop-up window "Find new Hardware" will come out.
7. Wait for Windows 98 to configure the card reader.
When the installation (of card reader driver) is successful, this pop-up window will
disappear automatically.
8. Congratulations! The process of installation is completed.
Windows ME
Card Reader is a driver-free device for Windows ME.
You don't have to install any driver (for it) and can plug into USB port directly.
Windows ME will detect and install all the associated files automatically.

5
A "Removable Device" icon will appear on the task bar when the installation is completed.
Windows 2000
1. Insert the Driver CD into the CD-ROM drive.
2. Click the CD-ROM drive icon and find the "Card Reader" folder.
3. Find "setup.exe" and double click it.
4. Follow the setup of "Install Wizard" to install the "USB Card Reader Driver".
5. Plug card reader into USB port and Windows 2000 will detect it automatically.
6. The pop-up window "Find new Hardware" will come out.
7. Wait for Windows 2000 to configure the card reader.
When the installation (of card reader driver) is successful, this pop-up window will
disappear automatically.

6
8. Congratulations! The process of installation is completed.
Windows XP
Card reader is a driver-free device for Windows XP.
You don't have to install any driver (for it) and can plug into USB port directly.
Windows XP will detect and install all the associated files automatically.
All the process sequences are listed below.
Step 1
Step 2
Step 3

7
Step 4 (depend on card reader)
A "Removable Device" icon will appear on the task bar when the installation is completed.
Linux
System Requirement:
1. kernel versions 2.2.7 and later contain the USB code.
Install Card Reader step by step:
1. configure USB into kernel. Use of "make menuconfig" is recommended. Under "USB
support", you need to select "Support for USB". You also need to select either UHCI (Intel
PIIX4, VIA, ...) support, UHCI Alternate Driver (JE) support or OHCI-HCD (Compaq,
iMacs, OPTi, SiS, ALi, ...) support. Which one you select is dependent on what kind of
motherboard or adapter you have.
2. select "USB Mass Storage support"
3. select "Preliminary USB Device Filesystem"
4. select "SCSI support"
5. selct "SCSI disk support"
6. select "/proc support"

8
7. Rebuild the kernel and the modules (if you configured to build as modules), and install the
new kernel and the new modules. Reboot the system.
If you are using modules, you need to load the following modules:
a. usbcore.o
b. usb-uhci.o, uhci.o or usb-ohci.o
c. usb-storage.o
Inspect the kernel logs. If there isn't anything that could be USB related, likely causes are
use of the wrong driver (UHCI when you needed OHCI or OHCI when you needed UHCI),
not physically installing the hardware, a BIOS configuration that disables USB or stuffing up
the configuration or installation of the kernel.
8. Use the mount command: mount -t usbdevfs none /proc/bus/usb.
Note that the 'none' keyword is arbitrary.
If you do not want to have to mount the filesystem each time you reboot the system, you
can add the following to /etc/fstab after the /proc entry.
none /proc/bus/usb usbdevfs defaults 0 0
9. Edit /etc/fstab
The exact syntax depends on the Card Reader. The best way is to make suitable entries in
/etc/fstab. The suitable entries for Card Reader would be:
/dev/sda /mnt/SMC auto noauto,user 0 0
/dev/sdb /mnt/CFC auto noauto,user 0 0
/dev/sdc /mnt/SDC auto noauto,user 0 0
/dev/sdd /mnt/MSC auto noauto,user 0 0
10. Create matching mount points in the actual filesystem:
mkdir /mnt/SMC
mkdir /mnt/CFC
mkdir /mnt/SDC
mkdir /mnt/MSC
11. Mount Card Reader:
mount /dev/sda
mount /dev/sdb
mount /dev/sdc
mount /dev/sdd
Note:
Note that the above entries assume you have no other SCSI devices.
If you do have other devices, then the USB disk may not be /dev/sda,
but could instead be /dev/sdb, /dev/sdc or some other device.

9