Asante Voyager II User manual

Step 1: Getting Started
Step 2: Initial Conguration
gure 2
1
2
3
Insert the supplied CD-ROM into your CD-ROM drive.
Execute IP Finder.exe.
Click the Search button to scan for your IP camera.
Selecte Ethernet, click Submit and click Exit.
Quick Start Guide
Thank you for choosing Asante
Voyager II megapixel IR IP Camera.
This guide oers the quickest way to install and
begin using the Voyager megapixel IR IP Camera.
No advanced installation options are discussed here. For more detailed
information, please refer to the User’s Manual on the supplied CD.
...............................................................................................................................................................
...............................................................................................................................................................
Connecting to a Network
The IP camera can be connected to an Ethernet network using
the RJ-45 port as shown. Connect the camera to an Ethernet hub,
switch or a router by using a standard cable. The IP address
will be acquired automatically. Plug in the cables as shown.
Step 4: Basic Wireless Setting
Step 3: Using a Web Browser
to Connect to The IP Camera
Click on Setting.
On the left side menu bar, select: Network>Wireless.
Click on Scan. This scan the nearby wireless access points and routers.
Select the desired router for the camera to connect to by clicking on it.
Further down on the page, click on Show all.
Please Note: Congure the authentication type parameters to match
the wireless security settings of the router you selected in step 3.
Click on Connect.
Once the status has shown Connected, you can unplug the cable
and mount the camera in your preferred location.
Enter the IP address of the camera in the browser address eld.
(ex: on gure 3, “192.108.251.206”)
When the login screen appears, enter your username and password.
The default username is root, the default password is also root.
1
1
2
3
3
4
1
2
5
6
7
2
3
4
5
gure 4
gure 7
gure 8
gure 10
gure 9
gure 1
gure 5
gure 6
Please note:
You might need to repeat the Log-in
for Quick Time.
When the username and password are conrmed, you will see the camera image.
As shown in gure 8. ( Allow a few seconds for video to load. )
Continue for wireless setup.
Note: Select HTTP mode if you cannot see the image.
gure 3
Non-Internet Explorer Version

Step 1: Getting Started
Step 3: Initial Conguration
Step 2: Enabling Active X
gure 2
gure 3 gure 4
gure 5
Open Internet Explorer.
Click on the Tools menu at the top of the screen
and select Internet Options.
Select the Security tab from the internet options menu.
Click the Custom Level button.
Reset the allowed level to Medium.
Enable ActiveX on the settings page.
1
2
3
1
2
3
3
4
4
5
6
6
Insert the supplied CD-ROM into your CD-ROM drive.
Execute IP Finder.exe.
Click the Search button to scan for your IP camera.
Select Ethernet, click Submit and click Exit.
...............................................................................................................................................................
...............................................................................................................................................................
Connecting to a Network
The IP camera can be connected to an Ethernet network using
the RJ-45 port as shown. Connect the camera to an Ethernet hub,
switch or a router by using a standard cable. The IP address
will be acquired automatically. Plug in the cables as shown.
Your browser must have Active X enabled to connect
to the IP camera.
Step 5: Basic Wireless Setting
Step 4: Using an Internet Explorer
to Connect to The IP Camera
Click on Setting.
On the left side menu bar, select: Network>Wireless.
Click on Scan. This scan the nearby wireless access points and routers.
Select the desired router for the camera to connect to by clicking on it.
Further down on the page, click on Show all.
Please Note: Congure the authentication type parameters to match
the wireless security settings of the router you selected in step 3.
Click on Connect.
Once the status has shown Connected, you can unplug the cable
and mount the camera in your preferred location.
Enter the IP address of the camera in the browser address eld.
(ex: on gure 5, “192.108.251.206”)
When the login screen appears, enter your username and password.
The default username is root, the default password is also root.
When the username and password are conrmed, a control setup screen
pops up under the IE address bar. Click “Run” to run the ActiveX control.
When ActiveX Control is installed successfully, you will see the camera
live view image.
1
1
2
3
4
1
2
3
4
5
6
7
2
3
4
5
gure 6
gure 7
gure 8
gure 9
gure 11
gure 10
5
6
gure 1
Internet Explorer Version Internet Explorer Version
Quick Start Guide
Thank you for choosing Asante
Voyager II megapixel IR IP Camera.
This guide oers the quickest way to install and
begin using the Voyager megapixel IR IP Camera.
No advanced installation options are discussed here. For more detailed
information, please refer to the User’s Manual on the supplied CD.
Internet Explorer Version