ASBER ERE-400 User manual

1
General instruction for installation, use and maintenance
ELECTRIC RANGES
Models:
ERE-400
ERE-800
ERE-1200
ERE-400 T
ERE-800 T
ERE-1200 T

2
Dear customer
We would like to thank You for the confidence you have shown in our product on purchasing a
professional appliance. We are totally convinced that in time you will be completely satisfied
with you purchase.
Take a few minutes of your time get to know the appliance with this instructions manual and
“down to work”: the easy to understand graphical information replaced pages full of writing.
Nevertheless, we recommend you thoroughly read this manual complied by ASBER’s kitchen
supervisors, in order to benefit to the maximum from the multiple possibilities and advantages
this appliance offers you.
Keep this manual near to the appliance and at all times in an accessible place.
ASBER
INDEX
INSTALATION................................................................................................................................................3
Generalandconnectiondimensions...........................................................................................3
Technicalspecification.................................................................................................................6
Positioningandlevelling..............................................................................................................7
Electricconnection......................................................................................................................7
USE...............................................................................................................................................................8
TurningtheapplianceON............................................................................................................8
TurningtheapplianceOFF...........................................................................................................8
MAINTENANCE.............................................................................................................................................8
ENVIRONMENTALPROTECTIONANDRECOMMENDATION.........................................................................9

3
INSTALATION
Generalandconnectiondimensions
ERE-400
W– pointer
K– control light
P– control knob
Z– power cable
ELECTRIC
PLATE
2600W

4
ERE-800
W – pointer
K – control light
P – control knob
Z – power cable
ELECTRIC
PLATE
2600W

5
ERE-1200
W – pointer
K – control light
P – control knob
Z – power cable
Figure1
REGULATED
LEEGS
ELECTRIC
PLATE
2600W

6
OFFMINIMUMMAXIMUM
Figure2
Technicalspecification
Table1
MODEL ERE-400 ERE-800 ERE-1200 ERE-400 T ERE-800 T ERE-1200 T
External
dimensions [mm]
Width 400 800 1200 400 800 1200
Depth 700 700 700 700 700 700
Height 850 850 850 280 280 280
Net weight [kg] 21 35 50
Number of
plates
Plate
2600W 2 4 6 2 4 6
Electric
power
50/60Hz
380-415 V
3N
Wire cross 5x2,5 5x2,5 5x2,5 5x2,5 5x2,5 5x2,5
Electrical protection 16A 25A 25A 16A 25A 25A
Power [kW] 5,2 10,4 15,6 5,2 10,4 15,6
Electric plate power regulation
Table2
Electric plate 0 1 2 3 1 5 6
2,6 kW 0 W 450 W 850 W 1300 W 1750 W 2150 W 2600 W


7
Positioningandlevelling
The positioning electrical and gas installation should always be carried out by an AUTHORISED
TECHNICIAN, observing the standards of each country.
•It is advisable to install an extraction hood for the optimum operation of the appliance.
•Place the appliance in a well-ventilated place.
•Level and adjust the height of the appliance. (Fig. 1) and (Fig. 1A)
Electricconnection
An AUTHORISED TECHNICIAN should always carry out the appliance’s electrical
connection.
The legal standards in force in each country on connections to the mains should be taken into
account.
Check that the mains voltage corresponds to that indicated on the nameplate.
Use cable sleeves made out of polychloroprene or other similar materials (H05RN-F), for the
connection.
A switch device should be installed next to the appliance for all the phases, with a gap of a
minimum of 3 mm between contacts. This switch will be equipped with fuses.
It is obligatory to earth the appliance. The manufacturer takes no responsibility if this
requirement is not fulfilled.
The section of cable sleeve and the rating of the fuses to be installed in the power switch are
indicated in diagram no. 2.
Place where power cable go through the devices is marked letter “C”.
WARNING !!! IMPORTANT !!!
Before putting the switchboard top on, fasten the electric supply cable tightly to the stuffing box.
When several appliances are installed in series, they should be earthed to each other using the
point assigned for this purpose, located in the appliance's base, at the back.
Letter „C” oznaczone sąjest wyjście kabla zasilającego z urządzenia.

8
USE
TurningtheapplianceON
Press the power switch situated on the outside of the appliance.
Turn the “P” control (Fig. 2) of the switch corresponding to the plate you want to turn ON, to the
chosen position or power (Table 2), and then the “K” pilot light will turn ON (Fig. 2) telling us
that the chosen plate and power are working.
TurningtheapplianceOFF
If you want to turn the plate OFF, turn the “P” control to the “OFF” position (Fig. 2). The
burner and the control light will turn OFF in this position.
WARNING !!! IMPORTANT !!!
Don’t leave the hotplates at the time included the absence of the heat (no dishes on the
plate). Overheat can damage the hotplate.
The device must be operated and stored in heated rooms during winter.
MAINTENANCE
Daily cleaning
In order for the appliance to work as new, it is advisable to follow the following instructions:
- don’t use gritty and abrasive detergents.
- don’t use a water hose to clean the appliance.
IMPORTANT NOTE:
The replacement of any functional component that can affect the safety of the appliance must be
carried out by an AUTHORISED TECHNICIAN.
Before making any changes, ensure that the power switch is OFF.

9
ENVIRONMENTALPROTECTIONANDRECOMMENDATION
On ending its useful life, this product must not be thrown away in a standard
rubbish bin, but must be left in an electrical waste and electronic equipment
collection point for recycling.
This is confirmed by the symbol on the product, user manual, or packaging.
Depending on the symbol, the materials can be recycled. By recycling and
other ways of processing electrical waste and electronic equipment, you can
significantly contribute to protecting the environment.
Contact your local authorities for more information of the nearest collection
point.
To conserve the environment at the end of the useful life of your product.
Leave it in the appropriate places in accordance with the current legislation.




Thisapplianceisonlyforprofessionalusageandmust
beusedbyqualifiedpersonnel.