Ascot 603/6449 User manual

7
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400800
Assembly is complete.
Width - 46cm
Depth - 52cm
Height - 96cm
Important – Please read these instructions fully before starting assembly
Customer Helpline: 08456 400800
Assembly Instructions -Please keep for future reference
Dimensions
Issue 1 - 9/02/10
Ascot Chair
If you need help or have damaged or missing parts, call the
603/6432
603/6449
603/6456
c:
d:
c:
After the sitting test,
re - tighten bolts again,
if any adjustment needed.
d:
It is highly recommend
to re - tighten all the bolts
again after using the chair
for 7 days.
Note : Please keep the
allen key to re - tighten
all bolts again when
required.
Assembly Instructions

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Care and maintenance
1
• Check you have all the
components and tools listed on
page 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product during assembly,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
• Maximum safe weight of
user: 110 Kgs.
Step 2
e:
Assembly Instructions
Screw the lock seats
with hand screw driver
by following the pre drilled
holes.
E
De:
a:
Tighten all bolts.
Note : Stand the chair on
a level floor.
a:
b:
Sit on the chair to
the legs.
6
Pre-drilled
hole
E
D
b:

2
Components - Parts
Please check you have all the parts listed below
Chair back x 1 Seat x 1
If you have damaged or missing components,
call the
Customer Helpline: 08456 400800
12
3
4Right side rail x 1Front leg frame x 1
BACK
5
c:
A
B
C
Assembly Instructions
d:
d:
c:
Stand the chair on a
floor. Insert bolts with
spring washers and
washers through side
rails holes into front leg
frame screw all bolts
by using ball allenkey .
3
A
G
B
C
Place the seat pad
on the table. Put the
chair frame on top of the
seat back.
2
Insert screw into
the pre - drilled holes on
the righ leg rail and
left leg rail using a
screwdriver.
F
6
BACK
1
34
5
6
7
KCAB
1
2
6
7
6
F
5Left side rail x 1 6Right leg rail x 1
7Left leg rail x 1
7

Components - Fittings
Please check you have all the fittings listed below
Note :The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Bolt x 8
B
Spring washerx 8
C
D
Washer x 8
F
Lock seat x 2 38mm Screwx 4
A
E
Screw x 4
3
G
Ball allenkey x 1
Tools required
Phillips screwdriver
(medium& large)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Assembly Instructions
Step 1
a:
4
A
a:
b:
b:
Put left side rail into
left side hole of the chair
back and right side rail
into right side hole.
Insert bolt with spring
washers and washers
through side rails holes
into the chair backs.
Screw all bolts by using
ball allenkey .
B
C
G
Do not fully tighten.
Fit the front leg frame
onto the right and left
side rails and right
and left leg rails .
and leg rails .
3
4
4
5
1
pre - drilled hole
A
B
C
Right side rail
Left side rail
Insert screw into the
pre-drilled holes in the
right leg rail and
left legs rail tighten
(although not fully) with
a screwdriver.
7
F
5
F
R
L
BACK
BACK
1
4
5
6
7
3
BACK
4
5
7
6
6
6 7