ASI EZ FILL Product manual

05 September 2018
EZ FILL™ FAUCET
AUTOMATIC
DECK MOUNTED FAUCET
INSTALLATION AND MAINTENANCE GUIDE

05 September 2018 05 September 2018
2
1
Unit Install Date
Unit Location in Facility
Unit S/N (From Label)
Supplied By
Original PO No.
ASI Order No.
TABLE OF CONTENTS PRE-INSTALLATION INFORMATION
Important: All plumbing is to be installed in accordance with applicable codes and
regulations.
CheCk Contents
Separate all parts from the packaging and check each part with the“Pack contents”section.
Pay attention to the dierent models variations.
Make sure all parts are accounted for before discarding any packaging material.
If any parts are missing, do not attempt to install your electronic faucet until you obtain the
missing parts.
Warnings
Do not install facing a mirror or any other electronic system operated by an infrared sensor.
To prevent reection problems, it is recommended to keep a minimum distance
of 1.50 meters between the faucet and any other objects.
PreParation for installation
Flush water supply lines thoroughly before installing the faucet. Do not allow dirt, Teon tape
or metal particles to enter the faucet.
Shut o water supply.
Installations in Australia and New Zealand must comply with the requirements of
AS/NZS 3500.
RECOMMENDED HOLE SIZE
2 PRE-INSTALLATION INFORMATION
3 PACK CONTENTS
4 TECHNICAL DATA
5-7 INSTALLATION
8-9 SETTINGS ADJUSTMENT
10 BATTERY REPLACEMENT INSTRUCTIONS
11 SPARE PARTS LIST
11 MAINTENANCE
12 WARRANTY
13 TROUBLESHOOTING

05 September 2018 05 September 2018
34
PACK CONTENTS EZFILL™ FAUCET
Familiarize yourself with the part names and conrm that the parts are included.
Batteries not included
B VERSION E VERSION
BATTERY BOX FOR
1.5V BATTERIES X 6 9V TRANSFORMER
1X FAUCET AND ATTACHMENTS
1X FILTER
1X ALLEN KEY
TECHNICAL DATA
EZFILL™ FAUCET (battery powered) - 235100
EZFILL™ FAUCET (transformer powered) - 235200
Power supply: 6X 1.5V AA batteries or 9V transformer
Recommended water
pressure:
8.00.5 bar (1167 PSI)
With water pressure of more than 8 bars,
use a pressure reducing valve for reduction.
Preset sensor range: 200mm / 7.87” (customizable with optional remote control)
Minimum sensor range: 35mm / 1.38”
Maximum sensor range: 300mm / 11.81”
Security time: 90 seconds (can be reduced with optional remote control)
Hot water temperature: Max 70C

05 September 2018 05 September 2018
5 6
INSTALLATION
STEP 1 PREPARATION FOR MOUNTING THE FAUCET
1Shut o the water supply.
2
Remove the hexagonal nut, the disk
and the gasket. Do not remove the
O-ring from the base of the faucet.
NUT
DISC
GASKET
ORING
STEP 2 INSTALLING THE FAUCET
1
Place the faucet with O-ring into the
hole in deck or lavatory. Make sure the
O-ring is located between the deck or
lavatory and the bottom of the faucet. ORING
2
Slide the gasket, disk and hexagonal
nut over the exible hose and secure
the faucet into place.
NUT
DISC
GASKET
NUT
DISC
GASKET
ORING
ORING
INSTALLATION
STEP 3 CONNECTING THE WATER SUPPLY
1
Connect the exible pipe to the water
supply.
For models with temperature control
connect the red exible pipe to the hot
water supply and the blue exible pipe
to the cold water supply.
MAKE SURE THAT THE FILTERS IS/ARE INSTALLED BETWEEN THE FLEXIBLE PIPE ANDTHE
SHUT OFF VALVE ANGLE VALVE NOT SUPPLIED.
2
Turn on the central water supply and
the shut-o valves (angle valves) and
check for leaks.

05 September 2018 05 September 2018
7 8
INSTALLATION
STEP 4 CONNECTING THE POWER SOURCE
1
BATTERY VERSION
Install the battery box at the wall
underneath the sink using the two
sided adhesive foam tape.The cable
connection must point down. (You
can use an optional extension cable in
order to assemble the battery box up
to 10ft. away from the sink.)
TRANSFORMER VERSION
Plug the transformer into the electricity
socket and connect the connectors.
2
In order to avoid entering into the
adjusting mode, wait 10 seconds
before operating the faucet. If the
range is unsatisfactory, refer to the
section titled “settings adjustment. 10
SECONDS
ABOUT Adjusting the settings with the remote control
If necessary, the sensor settings can be adjusted as following:
Shut o the water supply. In order to adjust the sensor with the remote control, hold the
remote control straight in front of the sensor in a distance of about 2015) “8-6cm). Choose
the function you want to adjust by pressing once on one of the function buttons. After
pressing once on a specic function button, a quick ashing of the LED at the front of the
sensor will occur. At this stage, you can change the setting by pressing the (+) or the (-)
buttons, every push will increase or decrease one level. After nishing the adjustment, turn
the water supply back on.
DETECTION RANGE: Only if necessary, use the remote control to adjust the
sensor range as follows:
Press the RANGE button. Wait until a quick ashing of the LED in the sensor
eye is perceived. Then, press + to increase the one level and – to reduce it
every push will increase or decrease one level.
NOTE: Once you have changed the detection range with the remote control, this distance
will be remembered by the sensor, even if the power source is disconnected.
DETECTION
RANGE
DELAY IN TIME
SECURITY TIME
COMFORT FLUSH
DELAY OUT TIME
TEMPORARY OFF
FUNCTION
RESET
HYGIENE FLUSH
SETTINGS ADJUSTMENT

05 September 2018 05 September 2018
SETTINGS ADJUSTMENT
DELAY IN TIME: If required, the delay in time can also be modied as follows:
Press the IN button. Wait until a quick ashing of the LED in the sensor eye is
perceived.Then, press + to increase the delay in time and – to reduce it.
DELAY OUT TIME: This button allows modifying the ushing start time after
the user moves away from the product. A delay out time close to 0 will save
more water. An increased delay out time will make the user experience more
comfortable.
If required, the delay out time can be modied as follows:
Press the OUT button. Wait until a quick ashing of the LED in the sensor eye
is perceived.Then, press + to increase the delay out time and – to reduce it.
TEMPORARY OFF FUNCTION: This function is ideal to perform any kind of
activity in front of the sensor without operating the system (for example,
cleaning).
The product will remain shut for 1 minute when this button is pressed once.
To cancel this function and to return to normal operation press the On/O
button again or wait 1 minute.
RESET BUTTON: This function restores all the factory settings except for the
sensor range. If required, press the Reset button and without releasing it,
press the + button once.
SECURITY TIME: The Security time, prevents continuous ushing of water
due to reections or vandalism. By default, if the sensor is covered for more
than 90 seconds the water ow will shut automatically. To resume regular
operation any obstruction must be removed.
Press the SEC button. Wait until a quick ashing of the LED of the sensor eye
is perceived.Then, press + to increase the security time and – to reduce it.
24 HOUR HYGIENE FLUSH: This model includes a 24 hours hygiene ush
which is disabled. To activate the hygiene ush, press the clock button. Wait
until a quick ashing of the LED in the sensor eye is perceived. Then press +
to activate the hygiene ush.To disable it again, press – to deactivate it.
COMFORT FLUSH: If your model includes a COMFORT FLUSH setting, it can
be activated by pressing the ush button.
When the button is pressed, one blink of the LED in the sensor eye is
perceived.The pre-programmed ush cycle will take place then.
The Comfort ush cannot be interrupted or deactivated by pressing any
button until it is over.
BATTERY REPLACEMENT INSTRUCTIONS
When the battery weakens, the red indicator light will blink at a constant rate.
The battery must be replaced within two weeks.
3 .Remove the old batteries2 .Carefully open the battery box1. Unscrew the holding
screw
5. Close the box
4. Replace the used batteries
with a new 6 X 1.5V batteries
(Lithium battery is recommended).
IMPORTANT: Spent batteries should not be disposed of with normal household
waste. Contact your local authority for information on waste disposal and
recycling.
New Battery
Old Battery
To replace the battery in Trendy B models:
9 10

05 September 2018 05 September 2018
11 12
SPARE PARTS LIST
Seals and Screws Kit 07210007
10-pack Sensor Kit 07220253
Cover Kit 07270004
10-pack Solenoid Valve Kit 07232005
Battery box with 6X1.5V AA batteries 06530093
Transformer 06522094
Remote Control 13B (Optional) 07100005
Soap & Water Remote Control (Optional) 07100014
MAINTENANCE
Filter cleaning instructions
This faucet is provided with one / two stainless steel lter(s) preventing foreign particles
to enter the lines. If the water ow has decreased, this can be because the lter(s) is/are
clogged. The lter(s) can be cleaned as follows:
1. Shut-o the water shut o valve (angle valve).
2. Disconnect the exible pipe/s.
3. Remove the lter(s) and wash it/them under running water.
4. Reassemble the parts.
5. Make sure that there is no water leakage.
Care and cleaning of chrome and special nishes
DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives, or the like.
Use of any prohibited cleaning or maintenance products or substances could damage the
surface of the faucet. For surface cleaning of faucet use ONLY soap and water, then wipe dry
with clean cloth or towel. When cleaning bathroom tile, the faucets should be protected
from any splattering of harsh cleansers.
We are pleased to oer this warranty covering ASI products furnished for your project.
This warranty replaces any other warranties or product descriptions, whether expressed or
implied, written or oral.
It is understood that the products for this project have been selected and inspected by the
purchaser, and have been accepted without qualication by the purchaser as merchantable,
t for the intended use, and satisfy the specications.
eZ fill™ soaP DisPenser ProDUCts Will Be free of DefeCts in Material anD
WorkManshiP DUring norMal Use for (2) tWo Years froMthe Date of inVoiCe.
Should the product fail under this warranty, the sole remedy, at the seller’s option, will be
to repair the defective product, refund the purchase price, provide an equivalent new or
refurbished product or provide parts only.
ASI AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES. This warranty excludes product damage due to incorrect installation, improper
maintenance, wear and tear, battery spoilage, product abuse, or product misuse, whether
performed by a contractor, service company, or the consumer.
ASI will not be responsible for labor costs associated with the removal, replacement, repair by
others, reinstallation, renovation or return of its products.
WARRANTY

05 September 2018
13
TROUBLESHOOTING
* “Security Mode”: If the sensor is covered for more than 90 sec. the faucet will automatically shut off water flow.
To return to normal operation remove any blockage.
** In this case, the water flow will stop anyway after 90 seconds because of the security time.
SOLUTIONCAUSEINDICATORPROBLEM
Replace batteryLow battery.
1. Sensor ashes
continuously
when user’s
hands are within
the sensor’s
range.
No water
coming out
of the faucet:
Increase the range1. Range is too short.2. LED in the
sensor does not
ash once when
user’s hands
are within the
sensor’s range.
Decrease the range2. Range is too long.
The battery must be replaced.3. Battery is completely used up
4. Unit is in“Security Mode”*
Eliminate cause of reection.
5. Sensor is picking up reections from the
washbasin or another object.
Connect the electronic unit
connectors to the solenoid.
1. Connectors between the electronic unit and
solenoid are disconnected.
3. LED in the
sensor ashes
once when user’s
hands are within
the sensor’s
range.
Unscrew solenoid, pull out the
plunger and the spring from the
solenoid and clean them. Use
scale remover material if needed.
When replacing the plunger,
please make sure that the spring
is in vertical position.
2. Debris or scale in solenoid.
Clean the orice or replace
diaphragm.
3. The central orice in the diaphragm is plugged
or the diaphragm is torn
Reduce the supply water
pressure.
4. The water supply pressure is higher than 8 bar.
Shut o water supply and
unscrew one of the exible pipes
in order to reduce the pressure
that blocks the product.
5. The water supply pressure is under 8 bars and
yet the pressure in the faucet’s body is higher. This
situation could be caused by a sudden increase
in the water supply pressure that the back check
prevents from dropping, even after water supply
pressure drops under 8 bars.
Clean the orice or replace
diaphragm.
Debris or scale in diaphragm
1. Sensor ashes
once when user’s
hands are within
the sensor’s
range.
Water ow
from spout
does not
stop:
Clean or eliminate case of
interference.
1. Sensor is dirty or covered.**
2. LED in the
sensor does not
ash once when
user’s hands
are within the
sensor’s range.
Decrease the range or eliminate
cause of reection.
2. Sensor is picking up reections from the
washbasin or another object.
Remove, clean, re-installFilter or aerator is clogged
Water ow
diminished

05 September 2018
441 Saw Mill River Road, Yonkers, NY 10701  [phone]  Web: americanspecialties.com