Asko W6424 User manual

Dear Customer,
Read these instructions carefully and completely before you install the
machine. The installation should be carried out by a qualified person who
is familiar with all local codes and ordinances for electrical and plumbing
connections. See also the general Safety Instructions in the Use & Care
Guide.
Cosmetic damage must be reported to the ASKO dealer within five
days from the date of purchase. As soon as you unpack the machine,
thoroughly check it for cosmetic damage.
Installation Instructions for Washing Machine
DOMESTIC

2
Installation
Connection to water supply
Hot water connection (depending on model)
A few seconds after you start a program, the
washing machine will begin to fill with water from
the hot and cold supplies. If for some reason no
hot water is available, the machine waits for one
minute and then fills with cold water only. The
wash drum does not start to rotate until it begins
to fill with water.
However, if you choose to connect your ECO-
machine to cold water only, it is important that
you shut offthe hot water connection.
See the "Settings" chapter for information on
how to switch between "Hot water On" and "Hot
water Off".
Read these instructions carefully and
completely before you install themachine. The
installation should be carried out by a qualified
person who is familiar with all local codes
and ordinances for electrical and plumbing
connections. Cosmetic damage must be
reported to your dealer within five days from the
date of purchase. After unpacking the washer,
thoroughly check the unit for cosmetic damage.
Leveling the machine
It is important that the machine is level to
prevent excessive vibrations during spin cycles.
Each foot of the washer is adjustable, so you
can level the washer on any surface.
Once it is level, securely tighten the lock nuts
on the feet to prevent excessive vibration during
spin cycles.
Be sure to tighten the
lock nuts securely
when you level the
machine.
Water supply connection
Since ASKO washers have a built-in heating
element, you only need a cold water inlet. The
connection should be made by someone who
is sufficiently skilled. Use the hose supplied
with the washer. (The inlet hose is marked for
correct connection.) The water pressure must
be in the range 15–146 PSI. A valve should be
fitted on the water supply pipe. If a new supply
pipe has been installed for the washer, it should
be flushed thoroughly to remove any foreign
particles that might clog the filter in the fill valve.
NOTE!
If the unit is installed on a second storey, follow
local building codes. We recommend installing a
drip pan.

3
Installation
Drain outlet connection
The machine is supplied with the outlet hose
already attached. The hose should be extended
over a suitable sink edge or drain pipe at a
height of 24" to 36" (610 mm to 914 mm) above
the bottom of the unit. (The lower height is
preferable.) Make sure the hose is not kinked.
24" to 36"
NOTE!
If the hose is extended, the internal diameter of
the coupling must not be less than ½".
WARNING!
Do not extend the drain hose higher than 36"
(914 mm) from the bottom of the unit.
Electrical Connections
The machine is delivered ready-fitted with a
plug and is intended for connection to an ASKO
Dryer, which is equipped with a matching
receptacle. The plug supplied with the washer
can only be used with an ASKO Dryer. If the
washer is used separately or with another dryer,
it must be on a separate 208-240 V single-
phase circuit.
If the machine is to be used in a wet area, the
supply must be protected by a residual current
device.
As supplied: 208-240 V, 60 Hz, 2000 W heating
element,15 A fuse required.
NOTE!
Repairs and maintenance relating to safety or
performance must be carried out by a qualif ed
professional.
WARNING!
Connection to a permanently wired supply point
must be made only by a qualified electrician
Grounding instructions
This appliance must be grounded. In the event
of malfunction or breakdown, grounding will
reduce the risk of electric shock by providing
a path of least resistance for electric current.
This appliance is equipped with a cord having
an equipment-grounding conductor and a
grounding plug. The plug must be plugged into
an appropriate outlet that is properly installed
and grounded in accordance with all local codes
and ordinances.
Freestanding installation
The washer can be placed next to the dryer.
It is essential that the machine is leveled and
the locknuts are tightened to prevent excessive
vibration during spin cycles. Also be sure to
leave a minimum of ½" of space between the
washer and the dryer. The height adjustment
for the washer is 33½" to 34½" (850 mm to 876
mm). Do not raise it higher than 34½" (876 mm).
WARNING!
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. Check with a qualified electrician
or serviceman if you are in doubt as to whether
the appliance is properly grounded.
Do not modify the plug provided with the
appliance. If it will not fit the outlet, have a proper
outlet installed by a qualified electrician.

4
Stacked installation
ASKO washers should never be stacked on a
counter or a dryer.You can, however, stack an
ASKO dryer on an ASKO washer. Refer to your
Dryer Use and Care Guide for instructions on
how to do this.
Built-in installation
ASKO washers can be installed beneath a
cabinet or worktop with a height of 34” to 35”
(863 to 889 mm) or in a closet. There must
be a gap of about ½” (12 mm) all around the
machine, including between the rear edge of
the machine’s top panel and the back wall.
The opening width must be at least 24½” (622
mm). Space must also be available for the fill
and drain hoses. See the illustration below for
measurements and positions. If the washer is
installed in a closet the door must be left open
while the washer is running.
If the drain outlet is higher than 24" (610 mm),
the connections will need to be recessed.
Installation

5

6

7

www.askona.com
We reserve the right to make changes.
WM70.1  en (05-17)