ASROCK K7UPGRADE-880 User manual

11
11
1
K7Upgrade-880
User Manual
Version 1.0
Published August 2004
Copyright©2004 ASRock INC. All rights reserved.

22
22
2
Copyright Notice:Copyright Notice:
Copyright Notice:Copyright Notice:
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in
any language, in any form or by any means, except duplication of documentation by
the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this manual may or may not be regis-
tered trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:Disclaimer:
Disclaimer:Disclaimer:
Disclaimer:
Specifications and information contained in this manual are furnished for informa-
tional use only and subject to change without notice, and should not be constructed
as a commitment by ASRock. ASRock assumes no responsibility for any errors or
omissions that may appear in this manual.
With respect to the contents of this manual, ASRock does not provide warranty of
any kind, either expressed or implied, including but not limited to the implied warran-
ties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the manual or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
ASRock Website: http://www.asrock.com

33
33
3
ContentsContents
ContentsContents
Contents
1.1.
1.1.
1. IntroductionIntroduction
IntroductionIntroduction
Introduction ............................................................................................................
............................................................................................................
...................................................... 55
55
5
1.1 Package Contents.............................................................. 5
1.2 Specifications.................................................................... 6
1.3 Motherboard Layout.......................................................... 8
1.4 ASRock I/O PlusTM ........................................................................................................ 9
2.2.
2.2.
2. InstallationInstallation
InstallationInstallation
Installation ................................................................................................................
................................................................................................................
........................................................ 1010
1010
10
Pre-installation Precautions........................................................ 10
2.1 CPUInstallation .................................................................. 11
2.2 Installation of CPU Fan and Heatsink ................................ 11
2.3 Installation of Memory Modules (DIMM) ............................ 12
2.4 Expansion Slots (K8 Bridge, PCI, and AGP Slots) .................... 14
2.5 Jumpers Setup .................................................................. 16
2.6 Onboard Headers and Connectors .................................. 18
2.7 Serial ATA (SATA) Hard Disks Installation ......................... 21
2.8 Hot Plug and Hot Swap Functions for SATA HDDs .......... 21
2.9 Making An SATADriver Diskette ........................................ 22
3.3.
3.3.
3. BIOS SBIOS S
BIOS SBIOS S
BIOS SETUP UTILITYETUP UTILITY
ETUP UTILITYETUP UTILITY
ETUP UTILITY ..........................................................................................
..........................................................................................
............................................. 2323
2323
23
3.1 Introduction........................................................................ 23
3.1.1 BIOS Menu Bar ...................................................... 23
3.1.2 Navigation Keys..................................................... 24
3.2 Main Screen ...................................................................... 24
3.3 Advanced Screen............................................................. 25
3.3.1 CPU Configuration.................................................. 26
3.3.2 Chipset Configuration ............................................ 29
3.3.3 ACPI Configuration................................................. 32
3.3.4 IDE Configuration ................................................... 33
3.3.5 PCIPnPConfiguration ............................................. 35
3.3.6 Floppy Configuration ............................................. 35
3.3.7 Super IO Configuration .......................................... 36
3.3.8 USB Configuration ................................................. 37
3.4 Hardware Health Event Monitoring Screen ...................... 38
3.5 Boot Screen ...................................................................... 38
3.5.1 Boot Settings Configuration................................... 39
3.5.2 BootDevice Priority................................................ 39
3.6 Security Screen ................................................................ 40
3.7 Exit Screen ........................................................................ 41

44
44
4
4.4.
4.4.
4. Software SupportSoftware Support
Software SupportSoftware Support
Software Support ..........................................................................................
..........................................................................................
............................................. 4242
4242
42
4.1 Install Operating System ................................................... 42
4.2 Support CD Information ..................................................... 42
4.2.1 Running Support CD .............................................. 42
4.2.2 Drivers Menu ......................................................... 42
4.2.3 Utilities Menu .......................................................... 42
4.2.4 Contact Information ................................................ 42

55
55
5
1.1.
1.1.
1. IntroductionIntroduction
IntroductionIntroduction
Introduction
Thank you for purchasing ASRock K7Upgrade-880 motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control. It de-
livers excellent performance with robust design conforming to ASRock’s commit-
ment to quality and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-by-
step guide to the hardware installation. Chapter 3 and 4 contain the configuration
guide to BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might be
updated, the content of this manual will be subject to change without
notice. In case any modifications of this manual occur, the updated
version will be available on ASRock website without further notice. You
may find the latest memory and CPU support lists on ASRock website as
well. ASRock website http://www.asrock.com
1.1 Package Contents1.1 Package Contents
1.1 Package Contents1.1 Package Contents
1.1 Package Contents
ASRock K7Upgrade-880 Motherboard
(ATX Form Factor: 12.0-in x 8.5-in, 30.5 cm x 21.6 cm)
ASRock K7Upgrade-880 Quick Installation Guide
ASRock K7Upgrade-880 Support CD
One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable
One Ribbon Cable for a 3.5-in Floppy Drive
One Serial ATA (SATA)Data Cable
One SerialATA (SATA) HDD Power Cable(Optional)
OneASRock I/O PlusTM Shield
One Jumper Cap Remover

66
66
6
1.2 Specifications1.2 Specifications
1.2 Specifications1.2 Specifications
1.2 Specifications
Platform: ATX Form Factor: 12.0-in x 8.5-in, 30.5 cm x 21.6 cm
CPU: 462-Pin Socket SupportingAMDAthlonTM /AthlonTMXP /DuronTM
and 32-bit Sempron Processor
Chipsets: North Bridge:
VIA KT880, FSB @ 400 MHz
South Bridge:
VIA VT8237, supports USB 2.0, ATA 133, SATA 1.5Gb/s
Memory: 4DDRDIMM Slots:DDR1,DDR2,DDR3,andDDR4
Support PC3200 (DDR400) / PC2700 (DDR333) /
PC2100 (DDR266), Max. 4GB
Dual Channel Memory Technology support (see CAUTION 1)
IDE: IDE1:ATA133 / UltraDMAMode 6
IDE2:ATA133 / UltraDMAMode 6
Support up to 4 IDE devices
Serial ATA: 2 SATA connectors
Support 1.5Gb/s data transfer rate
Floppy Port: Supports up to 2 floppy disk drives
Audio: 5.1 channels AC’97 Audio
LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN
Hardware Monitor: CPU Temperature Sensing
Motherboard Temperature Sensing
CPU Overheat Shutdown to Protect CPU Life
(ASRock U-COP)(see CAUTION 2)
CPU Fan Tachometer
Chassis Fan Tachometer
Voltage Monitoring: +12V, +5V, +3.3V, Vcore
K8 Bridge: Supports CPU upgrade fromAMD K7 462-Pin CPU to
AMD K8 754-Pin CPU (see page 14 for details)
PCI slots: 3 slots with PCI Specification 2.3
AGP slots: 2 AGP slots, support 1.5V, 8X/4X AGP card (see CAUTION 3)
1.5V_AGP1 supports for K7 AGP Interface
AGP2 supports for K8 AGP Interface
USB 2.0: 8 USB 2.0 ports:
include 6 ready-to-use USB 2.0 ports on the rear panel,
plus one on-board header supporting 2 extra USB 2.0 ports
(see CAUTION 4)

77
77
7
ASRock I/O PlusTM:1 PS/2 mouse port, 1 PS/2 keyboard port,
1 serial port: COM1,
1 parallel port: ECP/EPP support,
6 ready-to-use USB 2.0 ports,
1 RJ-45 port,
Audio Jack: Line In / Line Out / Microphone
BIOS: AMIBIOS
Supports “Plug and Play”
ACPI 1.1 compliance wake up events
SMBIOS 2.3.1 support
CPU frequency stepless control
(only for advanced users’ reference, see CAUTION 5)
OS: Microsoft®Windows®98SE / ME / 2000 / XP compliant
CAUTION!
1. This motherboard supportsDual Channel Memory Technology. Before you
implement Dual Channel Memory Technology, make sure to read the
installation guide of memory modules on page 12 for proper installation.
2. While CPU overheat is detected, the system will automatically shutdown.
Before you resume the system, please check if the CPU fan on the
motherboard functions properly and unplug the power cord, then plug it
back again. To improve heat dissipation, remember to spray thermal
grease between the CPU and the heatsink when you install the PC system.
3. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!
It may cause permanent damage!
4. Power Management for USB 2.0 works fine under Microsoft®Windows® XP
SP1 / 2000 SP4. It may not work properly under Microsoft®Windows® 98 /
ME.
5. Although this motherboard offers stepless control, it is not recommended
to perform over clocking. Frequencies other than the recommended CPU
bus frequencies may cause the instability of the system or damage the
CPU. The CPU host frequency of this motherboard is determined by the
jumper-setting. To perform over-clocking, you must set the FSB jumper
according to your AMD CPU before you use the “Manual” option as the
FSB setting in BIOS setup. Please check page 26 for details.

88
88
8
1.3 Motherboard Layout1.3 Motherboard Layout
1.3 Motherboard Layout1.3 Motherboard Layout
1.3 Motherboard Layout
1 PS2_USB_PWR1 Jumper 21 Chassis Fan Connector (CHA_FAN1)
2 CPU Fan Connector (CPU_FAN1) 22 System Panel Header (PANEL1)
3 CPU Multiplier Jumper (J1) 23 Power LED Header (PWR_LED1)
4 CPU Socket 24 Chassis Speaker Header (SPEAKER 1)
5 North Bridge Controller 25 USB 2.0 Header (USB67, Blue)
6 ATX 12V Connector (ATX12V1) 26 Clear CMOS Jumper (CLRCMOS2)
7 2 x 184-pin DDR DIMM Slots 27 South Bridge Controller
(Dual Channel A: DDR1, DDR3; Blue) 28 Infrared Module Header (IR1)
8 Secondary IDE Connector (IDE2, Black) 29 Game Port Connector (GAME1)
9 Primary IDE Connector (IDE1, Blue) 30 3 x PCI Slots (PCI1- 3)
10 FSB Select Jumpers (FSB_SEL0,FSB_SEL1) 31 Flash Memory
11 2 x 184-pin DDR DIMM Slots 32 AGP Slot (AGP2)
(Dual Channel B: DDR2, DDR4; Black) 33 J6 Jumper ( 5 x 2-Pin)
12 J2 / J3 / J14 Jumpers ( 3 sets of 1 x 2-Pin) 34 Future CPU Bridge (K8BRIDGE_1)
13 J5 / J4 Jumpers ( 2 sets of 8 x 2-Pin) 35 Front Panel Audio Header (AUDIO1)
14 J9 / J10 / J11 / J13 Jumper ( 5 sets of 1 x 3-Pin) 36 JR1 / JL1 Jumpers
15 Future CPU Bridge (K8BRIDGE_2) 37 AGP Slot (1.5V_AGP1)
16 J8 / J7 Jumpers ( 2 sets of 5 x 3-Pin) 38 ATX Power Connector (ATXPWR1)
17 Secondary Serial ATA Connector (SATA2) 39 Internal Audio Connector: AUX1 (White)
18 Primary Serial ATA Connector (SATA1) 40 Internal Audio Connector: CD1 (Black)
19 J12 Jumper ( 4 x 3-Pin) 41 Shared USB 2.0 Header (USB45, Blue)
20 Floppy Connector (FLOPPY1)
PS2_USB_PWR1
1
CPU_FAN1
1
J1
3
12
ATX12V1
6
SOCKET 462
4
VIA
KT880
Chipset
DDR1 (64/72 bit, 184-pin module)
DDR2 (64/72 bit, 184-pin module)
DDR3 (64/72 bit, 184-pin module)
DDR4 (64/72 bit, 184-pin module)
7
11
38
ATXPWR1
1.5V_AGP1
AGP2
PCI 2
PCI 3
PCI 1
K8BRIDGE_1
K8BRIDGE_2
SATA2
SATA1
VIA
VT8237
CMOS
Battery
CHA_FAN1
USB67
1
CLRCMOS2
PAN EL 1
HDLED RESET
PLED PWRBTN
1
SPEAKER1
1
PWR_LED1
1
26 222425
GAME1
1
IR1
1
28
4Mb
BIOS
31
Super
I/O
1
AUDIO1
JR1 JL1
34
35
36
Audio
CODEC
LAN
PHY
AUX1
CD1
1
USB45
Top:
Line In
Center:
Line Out
Bottom:
Mic In
USB 2.0
T: USB4
B: USB5
39
40
41
USB 2.0
T: USB2
B: USB3
USB 2.0
T: USB0
B: USB1
Top:
RJ-45
PARALLEL PORT
COM1
PS2
Mouse
PS2
Keyboard
FSB_SEL0
FSB_SEL1
1
1
IDE1
IDE2
FLOPPY1
1
1
J2
J3
1
J9
1
J10
1
J11
1
J13
J5
1
J7
1
J8
J14
J4
1
1
1
1
J12
J6
1
21.6cm (8.5 in)
30.5cm (12.0 in)
5
8
9
10
12
13
14
15
13
16
16
14
17
18
19
20
21
23
2729
30
32
12
33
37

99
99
9
1.4 ASRock I/O Plus1.4 ASRock I/O Plus
1.4 ASRock I/O Plus1.4 ASRock I/O Plus
1.4 ASRock I/O PlusTMTM
TMTM
TM
1 Parallel Port 7 2 x USB 2.0 Ports (USB0, USB1)
2 RJ-45 Port 8 2 x USB 2.0 Ports (USB2, USB3)
3 Line In (Light Blue) 9 Serial Port: COM1
4 Line Out (Lime) 10 PS/2 Keyboard Port (Purple)
5 Microphone (Pink) 11 PS/2 Mouse Port (Green)
6 2 x Shared USB 2.0 Ports (USB4, USB5)
12
3
4
5
6
7
8910
11

1010
1010
10
2.2.
2.2.
2. InstallationInstallation
InstallationInstallation
Installation
K7Upgrade-880 is an ATX form factor (12.0-in x 8.5-in, 30.5 cm x 21.6 cm)
motherboard. Before you install the motherboard, study the configuration of your
chassis to ensure that the motherboard fits into it.
Pre-installation PrecautionsPre-installation Precautions
Pre-installation PrecautionsPre-installation Precautions
Pre-installation Precautions
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
Before you install or remove any component, ensure that the
power is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
1. Unplug the power cord from the wall socket before touching any
component.
2. To avoid damaging the motherboard components due to static
electricity, NEVER place your motherboard directly on the carpet or
the like. Also remember to use a grounded wrist strap or touch a
safety grounded object before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-
static pad or in the bag that comes with the component.
5. When placing screws into the screw holes to secure the motherboard
to the chassis, please do not over-tighten the screws! Doing so may
damage the motherboard.

1111
1111
11
2.12.1
2.12.1
2.1 CPU InstallationCPU Installation
CPU InstallationCPU Installation
CPU Installation
Step 1. Unlock the socket by lifting the lever up to a 90° angle.
Step 2. Position the CPU directly above the socket such that its marked corner
matches the base of the socket lever.
Step 3. Carefully insert the CPU into the socket until it fits in place.
The CPU fits only in one correct orientation. DO NOT force the
CPU into the socket to avoid bending of the pins.
Step 4. When the CPU is in place, press it firmly on the socket while you push down
the socket lever to secure the CPU. The lever clicks on the side tab to
indicate that it is locked.
2.22.2
2.22.2
2.2 Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink
Installation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink
Installation of CPU Fan and Heatsink
After you install the CPU into this motherboard, it is necessary to install a
larger heatsink and cooling fan to dissipate heat. You also need to spray
thermal grease between the CPU and the heatsink to improve heat
dissipation. Make sure that the CPU and the heatsink are securely fas-
tened and in good contact with each other. Then connect the CPU fan to
the CPU FAN connector (CPU_FAN1, see Page 8, No. 2). For proper
installation, please kindly refer to the instruction manuals of the CPU fan
and the heatsink.
Step 1 Step 2, 3 Step 4

1212
1212
12
2.32.3
2.32.3
2.3 Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)
Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)
Installation of Memory Modules (DIMM)
K7Upgrade-880 motherboard provides four 184-pin DDR (Double Data Rate) DIMM
slots, and supportsDual Channel Memory Technology. For dual channel configuration,
you always need to install identical (the same brand, speed, size and chip-type)
DDR DIMM pair in the slots of the same color. In other words, you have to install
identical DDR DIMM pair in Dual Channel A (DDR1 and DDR3; Blue slots; see p.8
No.7) or identical DDRDIMM pair in Dual Channel B (DDR2 and DDR4; Black slots;
see p.8 No.11), so that Dual Channel Memory Technology can be activated. This
motherboard also allows you to install fourDDR DIMMs for dual channel configuration,
and please install identical DDR DIMMs in all four slots. You may refer to the Dual
Channel Memory Configuration Table below.
Dual Channel Memory Configurations
DDR1 DDR2 DDR3 DDR4
(Blue Slot) (Black Slot) (Blue Slot) (Black Slot)
(1) Populated - Populated -
(2) - Populated - Populated
(3) Populated Populated Populated Populated
1. If you want to install two memory modules, for optimal compatibility
and reliability, it is recommended to install them in the slots of the
same color. In other words, install them either in the set of blue slots
(DDR1 and DDR3), or in the set of black slots (DDR2 and DDR4).
2. If only one memory module or three memory modules are installed
in the DDR DIMM slots on this motherboard, it is unable to activate
the Dual Channel Memory Technology.
3. If a pair of memory modules is NOT installed in the same Dual
Channel, for example, installing a pair of memory modules inDDR1
and DDR2, it is unable to activate the Dual Channel Memory
Technology.

1313
1313
13
notch
break
notch
break
Installing a DIMMInstalling a DIMM
Installing a DIMMInstalling a DIMM
Installing a DIMM
Please make sure to disconnect power supply before adding or
removing DIMMs or the system components.
Step 1. Unlock a DIMM slot by pressing the retaining clips outward.
Step 2. Align aDIMM on the slot such that the notch on theDIMM matches the break
on the slot.
The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and theDIMM if you force the DIMM into the
slot at incorrect orientation.
Step 3. Firmly insert theDIMM into the slot until the retaining clips at both ends fully
snap back in place and the DIMM is properly seated.

1414
1414
14
2.42.4
2.42.4
2.4 Expansion SlotsExpansion Slots
Expansion SlotsExpansion Slots
Expansion Slots (K8 Bridge, PCI Slots, and AGP Slots)(K8 Bridge, PCI Slots, and AGP Slots)
(K8 Bridge, PCI Slots, and AGP Slots)(K8 Bridge, PCI Slots, and AGP Slots)
(K8 Bridge, PCI Slots, and AGP Slots)
There are 1 set of K8 Bridge, 3 PCI slots, and 2 AGP slots (the slot 1.5V_AGP1
supports for K7 AGP Interface, and the slot AGP2 supports for K8 AGP Interface) on
K7Upgrade-880 motherboard.
K8 Bridge
(Orange-Colored Bridge (K8BRIDGE_1) + Brown-Colored Bridge (K8BRIDGE_2)):
The set of K8 Bridge allows you to upgrade yourAMD 462-Pin CPU to AMD 754-Pin
CPU by installing an add-on ASRock 754Bridge (optional) into this K8 Bridge on
K7Upgrade-880 motherboard. Before you upgrade the AMD 462-Pin CPU to the
AMD 754-Pin CPU, it is necessary to adjust the jumper settings for those required
jumpers on K7Upgrade-880 motherboard. Please refer to the table below for the
correct jumper settings.
The orange-colored Bridge (K8BRIDGE_1) is not an AGP slot, and the
brown-colored Bridge (K8BRIDGE_2) is not an AMR slot! Please do
NOTinsertany AGPcardinto theorange-coloredBridge (K8BRIDGE_1)
and AMR card into the brown-colored Bridge (K8BRIDGE_2)! It may
cause permanent damage to the hardware!
CPUType Jumper Settings
2-Pin Jumpers 3-Pin Jumpers
462-PinCPU
(Default)
754-PinCPU
(Usinganadd-on
ASRock 754 Bridge)
1_2
J2/ J3 /J14
(page 8, No. 12)
(1 x 2-pin; short ) (5 x 2-pin; short )
(8 x 2-pin; short )
J6
(page 8, No. 33) J9/J10 J11/J13
(page 8, No. 14)
(1 x 3-pin;
short pin1, pin2)
J4/J5
(page 8, No. 13)
1
2
1
2
J7/J8
(page 8, No. 16)
J12
(page 8, No. 19)
(5 x 3-pin; short pin1, pin2)
(4 x 3-pin; short pin1, pin2)
2_3
J2/ J3 /J14
(page 8, No. 12)
(1 x 2-pin; open ) (5 x 2-pin; open )
(8 x 2-pin; open )
J6
(page 8, No. 33) J9/J10
J11/J13
(page 8, No. 14)
(1 x 3-pin;
short pin2, pin3)
J4/J5
(page 8, No. 13)
3
2
3
2
J7/J8
(page 8, No. 16)
J12
(page 8, No. 19)
(5 x 3-pin; short pin2, pin3)
(4 x 3-pin; short pin2, pin3)

1515
1515
15
NOTE
When adjusting the jumper settings, you may use the tool, Jumper Cap Remover, to help you
removing the jumper caps more easily. This Jumper Cap Remover is bundled in your motherboard
package, and please follow the “Jumper Cap Remover Instruction” to use it properly.
PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
AGP slot: The AGP slots are used to install a graphics card. Please insert theAGP
card with K7 AGP Interface into the slot 1.5V_AGP1 (see page 8 No. 37),
or insert the AGP card with K8 AGP Interface into the slot AGP2 (see
page 8 No. 32). Please do not installAGP cards into the slot 1.5V_AGP1
and the slot AGP2 at the same time. It may cause permanent damage to
the hardware.
Please doNOTuse a 3.3VAGP card on theAGP slot of this motherboard!
It may cause permanent damage! For the voltage information of your
AGP card, please check with the AGP card vendors.
Installing an expansion cardInstalling an expansion card
Installing an expansion cardInstalling an expansion card
Installing an expansion card
Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Step 2. Remove the system unit cover (if your motherboard is already installed in a
chassis).
Step 3. Remove the bracket facing the slot that you intend to use. Keep the screws
for later use.
Step 4. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Step 5. Fasten the card to the chassis with screws.
Step 6. Replace the system cover.

1616
1616
16
2.52.5
2.52.5
2.5 Jumpers SetupJumpers Setup
Jumpers SetupJumpers Setup
Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when jumper cap is
placed on these 2 pins.
Jumper Setting
PS2_USB_PWR1 Short pin2, pin3 to enable
(see p.8, No. 1) +5VSB (standby) for PS/2
or USB wake up events.
Note: To select +5VSB, it requires 2Amp and higher standby current provided by power supply.
JR1 / JL1
(see p.8, No. 36)
Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel audio
connectors can work.
Clear CMOS
(CLRCMOS2)
(see p.8, No. 26)
Note: CLRCMOS2 allows you to clear the data in CMOS. The data in CMOS includes system
setup information such as system password, date, time, and system setup parameters. To
clear and reset the system parameters to default setup, please turn off the computer and
unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper
cap to short the Clear CMOS jumper for 5 seconds.After shorting the Clear CMOS jumper,
please remove the jumper cap. However, please do not clear the CMOS right after you
update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS,
you must boot up the system first, and then shut it down before you do the clear-CMOS
action.
FSB_SEL0
FSB_SEL1
(see p.8, No. 10)
Note: The setting of the CPU front side bus frequency of this motherboard is by means of the
adjustment of jumper-setting. To perform over clocking, you must set the FSB jumper
according to your AMD CPU before you use the “Manual” option as the FSB setting in
BIOS setup. Please follow the figures above to set the CPU front side bus frequency.
+5V
1_2
+5VSB
2_3
Short Open
JR1JL1
2-pin jumper
FSB200MHz
FSB_SEL1
FSB_SEL0
2_3
1_2
FSB266MHz
FSB_SEL1
FSB_SEL0
1_2
1_2
1_2
FSB333MHz
FSB_SEL1
2_3
FSB_SEL0
FSB400MHz
FSB_SEL1
2_3
FSB_SEL0
2_3

1717
1717
17
CPUMultiplierJumper
(J1, 5 x 3-pin)
(see p.8, No. 3)
Note: The set of CPU Multiplier Jumper is only for advanced users to adjust the
multiplier of CPU. Please follow the table below to adjust the multiplier of CPU.
However, the system will work well without the adjustment of multiplier. You
do not have to adjust the multiplier for normal usage.
Multiplier FID0 FID1 FID2 FID3 FID4
5x 2-3 2-3 1-2 2-3 2-3
5.5x 1-2 2-3 1-2 2-3 2-3
6x 2-3 1-2 1-2 2-3 2-3
6.5x 1-2 1-2 1-2 2-3 2-3
7x 2-3 2-3 2-3 1-2 2-3
7.5x 1-2 2-3 2-3 1-2 2-3
8x 2-3 1-2 2-3 1-2 2-3
8.5x 1-2 1-2 2-3 1-2 2-3
9x 2-3 2-3 1-2 1-2 2-3
9.5x 1-2 2-3 1-2 1-2 2-3
10x 2-3 1-2 1-2 1-2 2-3
10.5x 1-2 1-2 1-2 1-2 2-3
11x 2-3 2-3 2-3 2-3 2-3
11.5x 1-2 2-3 2-3 2-3 2-3
12x 2-3 1-2 2-3 2-3 2-3
12.5x 1-2 1-2 2-3 2-3 2-3
13x 2-3 2-3 1-2 2-3 1-2
13.5x 1-2 2-3 1-2 2-3 1-2
14x 2-3 1-2 1-2 2-3 1-2
15x 2-3 2-3 2-3 1-2 1-2
16x 2-3 1-2 2-3 1-2 1-2
16.5x 1-2 1-2 2-3 1-2 1-2
17x 2-3 2-3 1-2 1-2 1-2
18x 1-2 2-3 1-2 1-2 1-2
19x 1-2 2-3 2-3 2-3 1-2
20x 1-2 1-2 2-3 2-3 1-2
21x 1-2 1-2 1-2 2-3 1-2
22x 1-2 2-3 2-3 1-2 1-2
23x 2-3 1-2 1-2 1-2 1-2
24x 1-2 1-2 1-2 1-2 1-2
Forexample,“AthlonXP2000+”is an 1666MHz CPU: 12.5 (Multiplier) X133MHz(Externalfrequency)=1666MHz
FID jumpers setting:
The jumper caps are not provided by ASRock. Please understand that ASRock
does not guarantee and support the adjustment of multiplier. These jumpers
setting may not apply to all multiplier-locked or even some unlocked AMD
CPU. Frequencies other than the recommended CPU bus frequencies may
cause the instability of the system or damage the CPU.
1
1
1
1
1
FID4
FID3
FID2
FID1
FID0
1
1
1
1
1
FID4
FID3
FID2
FID1
FID0

1818
1818
18
2.62.6
2.62.6
2.6 Onboard Headers and ConnectorsOnboard Headers and Connectors
Onboard Headers and ConnectorsOnboard Headers and Connectors
Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper
caps over these headers and connectors. Placing jumper caps over the
headers and connectors will cause permanent damage of the motherboard!
FDDConnector
(33-pinFLOPPY1)
(see p.8, No. 20)
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE Connector (Blue) Secondary IDE Connector (Black)
(39-pin IDE1, see p.8, No. 9) (39-pin IDE2, see p.8, No. 8)
Note: If you use only one IDE device on this motherboard, please set the IDE
device as “Master”. Please refer to the instruction of your IDE device vendor
for the details. Besides, to optimize compatibility and performance, please
connect your hard disk drive to the primary IDE connector (IDE1, blue) and
CD-ROM to the secondary IDE connector (IDE2, black).
Serial ATA Connectors These two Serial ATA (SATA)
(SATA1:see p.8,No. 18) connectors support SATA data
(SATA2:see p.8,No. 17) cables for internal storage
devices. The current SATA
interface allows up to 1.5 Gb/s
data transfer rate.
Serial ATA (SATA) Either end of the SATA data
Data Cable cable can be connected to the
SATA hard disk or the SATA
connector on the motherboard.
FLOPPY1
Pin1
IDE1
PIN1
IDE2
PIN1
connect the black end
to the IDE devices
connect the blue end
to the motherboard80-conductor ATA 66/100/133 cable
thered-striped side toPin1
SATA1
SATA2

1919
1919
19
Serial ATA (SATA) Please connect the black end of
Power Cable SATA power cable to the power
(Optional) connector on the drive. Then
connect the white end of SATA
power cable to the power
connector of the power supply.
USB 2.0 Header ASRock I/O PlusTM provides you
(9-pinUSB67) 6 ready-to-use USB 2.0 ports on
(see p.8, No. 25) the rear panel. If the rear USB
ports are not sufficient, this
USB 2.0 header is available to
support 2 extra USB 2.0 ports.
Shared USB 2.0 Header This USB45 connector is shared
(9-pinUSB45) with the USB 2.0 ports 4,5 on
(see p.8, No. 41) ASRock I/O PlusTM. When using
the front panel USB ports by
attaching the front panel USB
cable to this connector
(USB45), the USB ports 4,5 on
ASRockI/OPlusTM willnotbeable
to function.
Infrared Module Header This header supports an optional
(5-pin IR1) wireless transmitting and
(see p.8, No. 28) receiving infrared module.
Internal Audio Connectors These connectors allow you
(4-pin CD1, 4-pin AUX1) to receive stereo audio input
(CD1: see p.8, No. 40) from sound sources such as
(AUX1:see p.8, No. 39) a CD-ROM,DVD-ROM,TV
tuner card, or MPEG card.
Front Panel Audio Header This is an interface for the front
(9-pin AUDIO1) panel audio cable that allows
(see p.8, No. 35) convenient connection and
control of audio devices.
DUMMY
GND
+5V
IRTX
IRRX
1
CD-R
GND
GND
CD-L
AUX-R
GND
GND
AUX-L
CD1
AUX1
USB_PWR
USB_PWR
P+7
P-7
P+6
P-6
GND
GND
DUMMY
1
GND
GND
+5VA
BACKOUT-R
BACKOUT-L
AUD-OUT-L
AUD-OUT-R
MIC-POWER
MIC
1
connect to the SATA HDD
powerconnector
connect tothe
powersupply
USB_PWR
USB_PWR
P+5
P-5
P+4
P-4
GND
GND
DUMMY
1

2020
2020
20
System Panel Header This header accommodates
(9-pinPANEL1) several system front panel
(see p.8, No. 22) functions.
Chassis Speaker Header Please connect the chassis
(4-pinSPEAKER 1) speaker to this header.
(see p.8, No. 24)
Chassis Fan Connector Please connect the chassis fan
(3-pin CHA_FAN1) cable to this connector and
(see p.8, No. 21) match the black wire to the
ground pin.
CPU Fan Connector Please connect the CPU fan
(3-pin CPU_FAN1) cable to this connector and
(see p.8, No. 2) match the black wire to the
ground pin.
Game Connector Connect a Game cable to this
(15-pinGAME1) connector if the Game port
(see p.8, No. 29) bracket is installed.
ATX Power Connector Please connect an ATX power
(20-pinATXPWR1) supply to this connector.
(see p.8, No. 38)
GND
+12V
CHA_FAN_SPEED
+5V
DUMMY
DUMMY
SPEAKER
1
GND
PWRBTN#
PLED-
PLED+
DUMMY
RESET#
GND
HDLED+
HDLED-
1
CPU_FAN_SPEED
GND
+12V
MIDI_OUT
JAB2
JBY
J2Y
MIDI_IN
+5V
JAY
GND
GND
1
JAX
JAB1
+5V
JBX
JBB1
+5V