Asus VK278Q Series User manual

VE278Q/VK278Q Series
LED Monitor
User Guide
VE278Q
VK278Q
July 2010

ii
Copyright © 2010 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modied or altered, unless
such repair, modication of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identication or explanation and to the
owners’ benet, without intent to infringe.
Table of contents
Notices......................................................................................................... iii
Safety information ...................................................................................... iv
Care & Cleaning........................................................................................... v
1.1 Welcome! ...................................................................................... 1-1
1.2 Package contents......................................................................... 1-1
1.3 Assembling the monitor base..................................................... 1-2
1.4 Connect cables............................................................................. 1-2
1.5 Monitor introduction .................................................................... 1-3
1.5.1 Front of the LED monitor................................................. 1-3
1.5.2 Rear of the LED monitor ................................................. 1-5
2.1 Detaching the arm/stand(for VESA wall mount) ....................... 2-1
2.2 Adjusting the monitor.................................................................. 2-2
2.3 Install LifeFrame 2 software........................................................ 2-2
3.1 OSD (On-Screen Display) menu ................................................. 3-1
3.1.1 Howtorecongure.......................................................... 3-1
3.1.2 OSD Function Introduction.............................................. 3-1
3.2 Specications............................................................................... 3-6
3.3 Troubleshooting (FAQ)................................................................ 3-7
3.4 Supported Timing List ................................................................. 3-8

iii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
tothefollowingtwoconditions:
• Thisdevicemaynotcauseharmfulinterference,and
• Thisdevicemustacceptanyinterferencereceivedincluding
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
ClassBdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimits
aredesignedtoprovidereasonableprotectionagainstharmfulinterference
inaresidentialinstallation.Thisequipmentgenerates,usesandcan
radiateradiofrequencyenergyand,ifnotinstalledandusedinaccordance
withmanufacturer’sinstructions,maycauseharmfulinterferencetoradio
communications.However,thereisnoguaranteethatinterferencewill
not occur in a particular installation. If this equipment does cause harmful
interferencetoradioortelevisionreception,whichcanbedeterminedby
turningtheequipmentoffandon,theuserisencouragedtotrytocorrect
theinterferencebyoneormoreofthefollowingmeasures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmenttoanoutletonacircuitdifferentfromthatto
which the receiver is connected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
AsanEnergyStar® Partner,ourcompanyhasdetermined
thatthisproductmeetstheEnergyStar® guidelinesfor
energyefciency.
Canadian Department of Communications Statement
ThisdigitalapparatusdoesnotexceedtheClassBlimitsforradio
noiseemissionsfromdigitalapparatussetoutintheRadioInterference
RegulationsoftheCanadianDepartmentofCommunications.
ThisclassBdigitalapparatuscomplieswithCanadianICES-003.

iv
Safety information
• Beforesettingupthemonitor,carefullyreadallthedocumentationthat
camewiththepackage.
• Topreventreorshockhazard,neverexposethemonitortorainor
moisture.
• Nevertrytoopenthemonitorcabinet.Thedangeroushighvoltages
inside the monitor may result in serious physical injury.
• Ifthepowersupplyisbroken,donottrytoxitbyyourself.Contacta
qualiedservicetechnicianoryourretailer.
• Beforeusingtheproduct,makesureallcablesarecorrectlyconnected
andthepowercablesarenotdamaged.Ifyoudetectanydamage,
contact your dealer immediately.
• Slotsandopeningsonthebackortopofthecabinetareprovidedfor
ventilation.Donotblocktheseslots.Neverplacethisproductnearor
over a radiator or heat source unless proper ventilation is provided.
• Themonitorshouldbeoperatedonlyfromthetypeofpowersource
indicated on the label. If you are not sure of the type of power supply to
yourhome,consultyourdealerorlocalpowercompany.
• Usetheappropriatepowerplugwhichcomplieswithyourlocalpower
standard.
• Donotoverloadpowerstripsandextentioncords.Overloadingcan
resultinreorelectricshock.
• Avoiddust,humidity,andtemperatureextremes.Donotplacethe
monitor in any area where it may become wet. Place the monitor on a
stable surface.
• Unplugtheunitduringalightningstormorifitwillnotbeusedfora
longperiodoftime.Thiswillprotectthemonitorfromdamagedueto
powersurges.
• Neverpushobjectsorspillliquidofanykindintotheslotsonthe
monitor cabinet.
• Toensuresatisfactoryoperation,usethemonitoronlywithULlisted
computerswhichhaveappropriateconguredreceptaclesmarked
between 100-240V AC.
• Ifyouencountertechnicalproblemswiththemonitor,contacta
qualiedservicetechnicianoryourretailer.

v
Care & Cleaning
• Beforeyouliftorrepositionyourmonitor,itisbettertodisconnectthecables
andpowercord.Followthecorrectliftingtechniqueswhenpositioningthe
monitor.Whenliftingorcarryingthemonitor,grasptheedgesofthemonitor.
Do not lift the display by the stand or the cord.
• Cleaning.Turnyourmonitoroffandunplugthepowercord.Cleanthemonitor
surfacewithalint-free,non-abrasivecloth.Stubbornstainsmayberemoved
with a cloth dampened with mild cleaner.
• Avoidusingacleanercontainingalcoholoracetone.Useacleanerintended
forusewiththeLED.Neverspraycleanerdirectlyonthescreen,asitmaydrip
inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
• Thescreenmayickerduringtheinitialuseduetothenatureoftheuorescent
light.TurnoffthePowerSwitchandturnitonagaintomakesurethatthe
ickerdisappears.
• Youmayndslightlyunevenbrightnessonthescreendependingonthe
desktop pattern you use.
• Whenthesameimageisdisplayedforhours,anafterimageoftheprevious
screenmayremainafterswitchingtheimage.Thescreenwillrecoverslowlyor
you can turn off the Power Switch for hours.
• Whenthescreenbecomesblackorashes,orcannotworkanymore,contact
yourdealerorservicecentertoxit.Donotrepairthescreenbyyourself!
Conventions used in this guide
WARNING:Informationtopreventinjurytoyourselfwhentryingto
complete a task.
CAUTION:Informationtopreventdamagetothecomponentswhen
tryingtocompleteatask.
IMPORTANT:InformationthatyouMUSTfollowtocompleteatask.
NOTE:Tipsandadditionalinformationtoaidincompletingatask.

vi
Wheretondmoreinformation
Refertothefollowingsourcesforadditionalinformationandforproductand
software updates.
1. ASUS websites
TheASUSwebsitesworldwideprovideupdatedinformationonASUS
hardware and software products. Refer to http://www.asus.com
2. Optional documentation
Yourproductpackagemayincludeoptionaldocumentationthatmayhave
been added by your dealer. These documents are not part of the standard
package.

1-1ASUSLEDMonitorVE278Q/VK278QSeries
1.1 Welcome!
ThankyouforpurchasingtheASUS®VE278Q/VK278QSeriesLEDmonitor!
ThelatestwidescreenLEDmonitorfromASUSprovidesacrisper,broader,and
brighterdisplay,plusahostoffeaturesthatenhanceyourviewingexperience.
Withthesefeatures,youcanenjoytheconvenienceanddelightfulvisual
experiencethattheVE278Q/VK278QSeriesbringsyou!
1.2 Package contents
CheckyourVE278Q/VK278QSeriesLEDmonitorpackageforthefollowingitems:
LED monitor
Monitor base
1xCD(OnlyavailableformodelVK278Q)
Quickstartguide
Warranty card
1xPowercord
1xVGAcable
1xWebCamUSBcable(OnlyavailableformodelVK278Q)
1xDVIcable
1xAudiocable
Ifanyoftheaboveitemsisdamagedormissing,contactyourretailer
immediately.

1-2 Chapter1:ProductIntroduction
1.3 Assembling the monitor base
To assemble the monitor base:
1. Attachthebasetothearmandxwiththescrewtojointhemtightly.Youcan
easilytightenthescrewbyngers.
2. Adjustthemonitortotheanglethatismostcomfortableforyou.
We recommend that you cover the table surface with soft cloth to prevent
damagetothemonitor.
1
2
Make sure to screw the base to the arm tightly.
1.4 Connect cables
To connect cables:
Connectthecablesyouneedbasedonchapter1.5.2,page1-5.

1-3ASUSLEDMonitorVE278Q/VK278QSeries
1.5 Monitor introduction
1.5.1 Front of the LED monitor
12 3 4 56 7
1. Button:
• Automaticallyadjusttheimagetoitsoptimizedposition,clock,and
phasebylongpressingthisbuttonfor2-4seconds(forVGAmodeonly).
• Usethishotkeytoswitchfromsixvideopresetmodes(SceneryMode,
StandardMode,TheaterMode,GameMode,NightViewMode,and
sRGBMode)withSPLENDID™VideoEnhancementTechnology.
• ExittheOSDmenuorgobacktothepreviousmenuastheOSDmenu
is active.
2. Button:
• Press this button to activate the Picture-in-picture function.
• Both the DVI and HDMI input source should not be selected as both the
Main and PIP source simultaneously.
3. Button:
• Press this button to decrease the value of the function selected or move
tothenextfunction.
• This is also a hot key for Volume adjustment.
4. MENUButton:
• Press this button to enter the OSD menu.
• Pressthisbuttontoenter/selecttheicon(function)highlightedwhilethe
OSD is activated.

1-4 Chapter1:ProductIntroduction
5. Button:
• Press this button to increase the value of the function selected or move
right/uptothenextfunction.
• ThisisalsoahotkeyforBrightnessadjustment.
6. InputSelectButton:
• UsethishotkeytoswitchfromVGA,DVI,HDMIandDisplayPortinput
signal.
Press (InputSelectbutton)todisplayHDMIsignals
after you connect HDMI cable with the monitor.
7. PowerButton/PowerIndicator:
• Pressthisbuttontoturnthemonitoron/off.
• The color definition of the power indicator is as the below table.
Status Description
Blue ON
Amber Standby mode
OFF OFF

1-5ASUSLEDMonitorVE278Q/VK278QSeries
1.5.2 Rear of the LED monitor
Screw Holes for
VESA Wall Mount
Rear connectors
12 3 4 56
7
8
1 AC-IN port
2 DisplayPort
3 HDMI-IN port
4 DVI port
5 VGA port
6 Audio Line-in port
7 Earphone-out port
8 USB-IN port (Only available for model VK278Q)

2-1 Chapter2:Setup
2.1 Detaching the arm/stand
(for VESA wall mount)
ThedetachablestandoftheVE278Q/VK278QSeriesLEDmonitorisspecially
designedforVESAwallmount.
To detach the arm/stand:
1. Disconnectpowerandsignalcables.Carefullyput the front of the monitor
face down on a clean table.
2. Useascrewdrivertoremovethe two screws that secure the stand to the
monitor.
3. Detach the stand from the monitor.
• Werecommendthatyoucoverthetablesurfacewithsoftclothtoprevent
damagetothemonitor.
• Holdthestandofthemonitorwhileremovingthescrews.
• TheVESAwallmountkit(100x100mm)ispurchasedseparately.
• UseonlytheULListedWallMountBracketwithminimumweight/load22.8
Kg(Screwsize:4x12mm).

2-2ASUSLEDMonitorVE278Q/VK278QSeries
2.2 Adjusting the monitor
• Foroptimalviewing,werecommendthatyoulookatthefullfaceofthe
monitor,thenadjustthemonitortotheanglethatismostcomfortableforyou.
• Holdthestandtopreventthemonitorfromfallingwhilechangingitsangle.
• Youcanadjustthemonitor’sanglefrom-5˚to20˚.
-5 ~ 20
2.3 Install LifeFrame 2 software
ASUSVK278Qseriesprovidestheeasy-to-useLifeFrame 2 software that can work
withthewebcam,allowinguserstocreatetheirownphotosorvideoclips.
• TheLifeFrame 2 software currently supports Microsoft®Windows®7/Vista/
XPServicePack2operatingsystems.
• TheLifeFrame 2 software is bundled in the support CD.
Installation instructions
1. Close all other applications.
2. Insert the support CD into the optical drive and run the LifeFrame 2program.
3. Follow the on-screen instructions to complete the installation.

3-1 Chapter3:GeneralInstruction
3.1 OSD (On-Screen Display) menu
3.1.1 Howtorecongure
VE278
Splendid
Color
Image
Sound
PIP Settings
Input Select
Move Menu Exit
System Setup
Scenery Mode
Standard Mode
Theater Mode
Game Mode
Night View Mode
sRGB
1. PresstheMENUbuttontoactivatetheOSDmenu.
2. Press and tonavigatethroughthefunctions.Highlightandactivate
thedesiredfunctionbypressingtheMENUbutton.Ifthefunctionselected
hasasub-menu,pressand againtonavigatethroughthesub-menu
functions.Highlightandactivatethedesiredsub-menufunctionbypressing
theMENUbutton.
3. Press and tochangethesettingsoftheselectedfunction.
4. ToexittheOSDmenu,pressthe button. Repeat step 2 and step 3 to
adjust any other function.
3.1.2 OSD Function Introduction
1. Splendid
Thisfunctioncontainssixsub-functionsthatyoucanselectforyour
preference.EachmodehastheResetselection,allowingyoutomaintain
yoursettingorreturntothepresetmode.
VE278
Splendid
Color
Image
Sound
PIP Settings
Input Select
Move Menu Exit
System Setup
Scenery Mode
Standard Mode
Theater Mode
Game Mode
Night View Mode
sRGB
• Scenery Mode:Thisisthebestchoiceforsceneryphotodisplayingwith
SPLENDID™VideoEnhancement.

3-2ASUSLEDMonitorVE278Q/VK278QSeries
• Standard Mode:Thisisthebestchoicefordocumenteditingwith
SPLENDID™VideoEnhancement.
• Theater Mode:Thisisthebestchoiceformoviewatchingwith
SPLENDID™VideoEnhancement.
• Game Mode:ThisisthebestchoiceforgameplayingwithSPLENDID™
Video Enhancement.
• Night View Mode:Thisisthebestchoiceforplayingdark-scenegameor
watchingmoviewithSPLENDID™VideoEnhancement.
• In the Standard Mode and sRGB,theSaturation,Color Temp.,Skin
Tone,Sharpness,andASCRfunctionsarenotuser-configurable.
2. Color
Selecttheimagecoloryoulikefromthisfunction.
VE278
Splendid
Color
Image
Sound
PIP Settings
Input Select
Move Menu Exit
System Setup
Brightness
Contrast
Saturation
Color Temp
90
80
User Mode
Skin Tone
• Brightness:Theadjustingrangeisfrom0to100.The button is also a
hot key to activate this function.
• Contrast:Theadjustingrangeisfrom0to100.
• Saturation:Theadjustingrangeisfrom0to100.
• Color Temp.:Containsthreepresetcolormodes(Cool,Normal,Warm)
andoneUserMode.
• Skin Tone:ContainsthreecolormodesincludingReddish,Natural,and
Yellowish.
IntheUserMode,colorsofR(Red),G(Green),andB(Blue)are
userconfigurable;theadjustingrangeisfrom0~100.

3-3 Chapter3:GeneralInstruction
3. Image
YoucanadjusttheimageSharpness,TraceFree,AspectControl,Position
(VGAonly),andFocus(VGAonly)fromthismainfunction.
VE278
Splendid
Color
Image
Sound
PIP Settings
Input Select
Move Menu Exit
System Setup
Focus
Sharpness
Trace Free
Aspect Control
ASCR
50
0
Full
Position
• Sharpness:Adjuststhepicturesharpness.Theadjustingrangeisfrom0
to 100.
• Trace Free:SpeedsuptheresponsetimebyOverDrivetechnology.The
adjustingrangeisfromlower0tofaster100.
• Aspect Control:Adjuststheaspectratioto“Full”,“4:3”,“1:1”,or“Over
Scan”(OnlyavailableforHDMIinput).
• ASCR:SelectYESorNOtoenableordisabledynamiccontrastratio
function.
• Position:Adjuststhehorizontalposition(H-Position)andthevertical
position(V-Position)oftheimage.Theadjustingrangeisfrom0to100
(OnlyavailableforVGAinput).
• Focus:ReducesHorizontal-linenoiseandVertical-linenoiseoftheimage
byadjusting(Phase)and(Clock)separately.Theadjustingrangeisfrom
0to100(OnlyavailableforVGAinput).
4. Sound
Adjuststhesoundsettingstoyourpreference.
VE278
Splendid
Color
Image
Sound
PIP Settings
Input Select
Move Menu Exit
System Setup
Volume
Bass
Treble
Balance
50
50
50
50
OFFMute

3-4ASUSLEDMonitorVE278Q/VK278QSeries
• Volume:Adjuststheoutputvolumelevel.The button is also a hot
key to activate this function.
• Bass:Adjuststheoutputbasslevel.
• Treble:Adjuststheoutputtreblelevel.
• Balance:Adjuststhebalancebetweentheleftandrightfrontspeakers.
• Mute:Mutestheoutputvolume.
5. PIP Settings
ThePIPSettingsallowsyoutoopenupanothersub-windowconnected
fromanothervideosourcebesidesthemain-windowfromyouroriginal
videosource.Byactivatingthisfunction,youcanhavetwopicturesfromtwo
different video sources displayed by one monitor.
VE278
Splendid
Color
Image
Sound
PIP Settings
Input Select
Move Menu Exit
System Setup
PIP Mode
PIP Source
Size
Position
OFF
Swap
• PIP Mode:TurnsthePIPfunctiononoroff.
• PIP Source:SelectsthevideoinputsourcefromVGA,DVI,HDMI,or
DisplayPort connector.
• Size:AdjuststhePIPsize.Theoptionsare:Small,Middle,orLarge.
• Position:AdjuststhePIPpositioninthemain-window.Theoptionsare:
Right-Top,Left-Top,Right-Bottom,orLeft-Bottom.
• SWAP:Swapsthesourceofthemainandsub-window.
Both the DVI and HDMI input sources should not be selected each for
the Main and PIP source simultaneously.
Main-Channel
Sub-Channel
VGA DVI HDMI DisplayPort
VGA • • •
DVI •X•
HDMI •X•
DisplayPort • • •

3-5 Chapter3:GeneralInstruction
6. Input Select
Select the input source from VGA,DVI,HDMI,orDisplayPort.
VE278
Splendid
Color
Image
Sound
PIP Settings
Input Select
Move Menu Exit
System Setup
VGA
DVI
HDMI
DisplayPort
7. System Setup
Adjuststhesystemconfiguration.
VE278
Splendid
Color
Image
Sound
PIP Settings
Input Select
Move Menu Exit
System Setup
Language
All Reset
Splendid Demo Mode OFF
OFF
English
AI Light
OSD Setup
Information
• Splendid Demo Mode:ActivatethedemomodefortheSplendid
function.
• AI Light:Automaticallyadjustthescreenbacklightaccordingto
thesurroundings.Themonitorbacklightwillturnbrighterinabright
surroundings,orturndarkerinadarksurroundings.Asthelightsensoris
locatedonthetopofthemonitor,donotblockthesensingarea.
• OSD Setup:Adjuststhehorizontalposition(H-Position),verticalposition
(V-Position),OSDTimeout,DDD/CI,andTransparencyoftheOSD
screen.
• Information:Displaysthemonitorinformation.
• Language:SelectsOSDlanguage.TheselectionsareEnglish,French,
German,Spanish,Italian,Dutch,Russian,TraditionalChinese,Simplified
Chinese,andJapanese.
• All Reset:Setto“Yes”torevertallsettingstothefactorydefaultmode.

3-6ASUSLEDMonitorVE278Q/VK278QSeries
3.2 Specications
Model VE278Q VK278Q
PanelSize 27.0”W(68.6cm) 27.0”W(68.6cm)
Max.Resolution 1920x1080 1920x1080
Brightness(Typ.) 300cd/m
2
300cd/m
2
IntrinsicContrastRatio(Typ.) 1000:1 1000:1
ViewingAngle(CR=10) 160°(V)/170°(H) 160°(V)/170°(H)
Display Colors 16.7M(6bitHiFRC) 16.7M(6bitHiFRC)
Response Time 2ms(GraytoGray) 2ms(GraytoGray)
Webcam(built-in) - 2.0M
Satellite Speaker 3Wx2stereo 3Wx2stereo
Earphone Output Yes Yes
Sound from HDMI Yes Yes
HDMI input Yes Yes
DVI input DVI with HDCP DVI with HDCP
D-Sub input Yes Yes
DisplayPort input Yes Yes
Audio Line-in Yes Yes
PowerONConsumption 45W 45W
Tilt -5°~+20° -5°~+20°
VESAWallMounting Yes(100mmx100mm) Yes(100mmx100mm)
Phys.Dimension(WxHxD) 643x445.6x220 643x459.6x220
BoxDimension(WxHxD) 732x560x176 732x560x176
NetWeight(Esti.) 6.5kg 6.5kg
GrossWeight(Esti.) 9.8kg 9.8kg
VoltageRating AC100~240V(Built-in) AC100~240V(Built-in)
*Specicationsaresubjecttochangewithoutnotice.

3-7 Chapter3:GeneralInstruction
3.3 Troubleshooting (FAQ)
Problem Possible Solution
PowerLEDisnotON • Press the button to check if the monitor is in the
ONmode.
• Check if the power cord is properly connected to the
monitor and the power outlet.
ThepowerLEDlightsamberand
thereisnoscreenimage
• Check if the monitor and the computer are in the
ONmode.
• Makesurethesignalcableisproperlyconnected
the monitor and the computer.
• Inspectthesignalcableandmakesurenoneofthe
pins are bent.
• Connect the computer with another available
monitortocheckifthecomputerisproperlyworking.
Screenimageistoolightordark • AdjusttheContrastandBrightnesssettingsvia
OSD.
Screenimageisnotcenteredor
sizedproperly • Press the button for two seconds to
automaticallyadjusttheimage.
• AdjusttheH-PositionorV-Positionsettingsvia
OSD.
Screenimagebouncesorawave
patternispresentintheimage
• Makesurethesignalcableisproperlyconnectedto
the monitor and the computer.
• Move electrical devices that may cause electrical
interference.
Screenimagehascolordefects
(whitedoesnotlookwhite)
• Inspectthesignalcableandmakesurethatnoneof
the pins are bent.
• Perform Reset via OSD.
• AdjusttheR/G/BcolorsettingsorselecttheColor
Temperature via OSD.
Screenimageisblurryorfuzzy • Press the button for two seconds to
automaticallyadjusttheimage(forVGAmodeonly).
• AdjustthePhaseandClocksettingsviaOSD.
Nosoundorsoundislow • Ensure that the audio cable is properly connected to
the monitor and the computer.
• Adjustthevolumesettingsofbothyourmonitorand
computer.
• Ensure that the computer sound card driver is
properly installed and activated.
Webcamisnotworking
(forVK278Qonly)
• MakesurethatyouhaveconnectedtheUSB2.0
cable securely to both the LED monitor and your
computer.
• Make sure that you use the Microsoft Windows
Vista/XPServicePack2operationsystems.