At Home Collection NEW ENGLAND US927 User manual

Assembly Instructions
Please keep for future reference
Important - Please read these instructions fully before starting assembly
If you need help of have damaged or missing parts, calls the JDW Customer Helpline: 0871 231 2000
Dimensions No. people Assembly Time
Width: 19cm
Depth: 25cm
Height: 65cm (approx.)
30 Mins
NEW ENGLAND 4 DRAWER UNIT CAT NO: QN856
CAT NO: US927

1
Safety and Care Advice
Important –Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3..
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
•Assemble the item as close
room) as possible.
•Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
•This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
•Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
Handy Hints
• We do not
recommend the use
of power drill/drivers
for inserting screws,
as this could damage
the using. Only use hand
screwdrivers
CAT NO: QN856
WARNING
In order to help prevent overturning –
To help prevent product toppling over please follow the below steps:-
Do not allow children to climb or hang on the furniture
Do not place heavy items in the top drawers
Do not place heavy items on top of the furniture, unless the furniture has been
designed for this purpose
You will need to provide wall plugs and screws applicable for your wall type
CAT NO: US927

10
x1
19(w)cm x 25(d)cm
13.6(w)cm x 23.7(d)cm 13.6(w)cm x 23.7(d)cm 13.6(w)cm x 6(d)cm
13.2(w)cm x 12.5(h)cm 21.7(w)cm x 12.5(h)cm 20.6(w)cm x 12.2(d)cm 11.5(w)cm x 12.5(h)cm
23.8(d)cm x 63.8(h)cm 23.8(d)cm x 63.8(h)cm
x1 x1
x1
Components -Panels
Please check you have all the panels listed below

12 12 14
44
Note:
may be supplied than are required.
Components - Fittings
Male Camlock x Female Camlock x
Handle x
Phillips screwdriver
(medium & large)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screws length is measured from the head tothe point (30mm screw shown).
Tools required
16

Connect the male
camlock as directed in
the assembly instructions
using a screwdriver.
Push the male camlock
into the entry hole.
lnsert the female
camlock as shown in the
instructions
Note: ensure that the
Turn the female camlock
clockwise with a
arrow on the top of the
camlock points towards
the entry hole for the
male camlock.
screwdriver.
You should feel a click
when the camlock is
locked in place.
The joint is now secure.
Using Camlocks

A
A
A
A
A
A
A
A
A
A
A
A
x4
To assemble the drawers
1. Screw drawer front 10 to 2 x
drawer sides 11 using
4 x screw K as shown using a
Phillips Screwdriver.
2. Slide drawer bottom 12 along
grooves in 2 x panels 11.
3. Connect drawer back 13 to
2 x drawer sides 11 with 4 x
screws K using a Phillips
Screwdriver
4. Connect handle J to drawer
front 10 with 1 x screw with
a Phillips Screwdriver.
5. Repeat steps above to
complete 4 x drawers.
11
12
11
13
11
10
7
8
7
8
8
9
8
8
9
8
10
10
8
7
7
3
2
1
1. Insert 4 x Male camlocks A
into right side panel 3 as
shown.
2. Insert 4 x Male camlocks A
into left side panel 2 as shown.
3. Insert 4 x Male camlocks A
and 2 x wooden dowel into
Top panel 1 as shown.
3
2
1

3
1. Connect 2 x supports 4 to
left side panel by locating
them onto 2 x male camlocks.
2. Insert 4 x female camlocks
into the under side of supports
4 as shown.
Use a screwdriver to turn the
female camlock clockwise to
lock.
“Using Camlocks”
section at the front of this
instruction for further
assistance.
Please refer to the
4
2
4
2
4
4
4
5
5
6
1. Insert 2 x Dowels C into the
end of Front rail 6 as shown.
2. Insert 4 x Dowels into the
sides of 2 x Supports 5 as
shown.
3. Locate Front Rail 6 and 2 x
supports onto Left side
panel as shown.
2
6
5
6
5
2
5
1. Insert 2 x Dowels C into the
end of Front rail 6 as shown.
2. Insert 4 x Dowels into the
sides of 2 x Supports 5 as
shown.
3. Locate 4 x Male Camlocks in
right side panel 3 into
adjacent holes in 2 x supports
4 as shown.
4. Insert 4 x female camlocks
into the underside 2 x support 4
as shown.
6
5
65
5
3
4
4
Use a screwdriver to turn the
female camlock clockwise to
lock.
“Using Camlocks”
section at the front of this
instruction for further
assistance.
Please refer to the
3
4
4
6

1. Locate top panel 1 onto left
side panel 2 and right side
panel 3 as shown.
2.Insert 4 x female camlocks
into side panels and .
Use a screwdriver to turn the
female camlock clockwise to
lock.
“Using Camlocks”
section at the front of this
instruction for further
assistance.
Please refer to the
1
1
2
3
2
3
23
1. Insert drawers into the unit.
Assembly Complete
7
6
7

Washer x 2
The unit is floor
standing, but it is
recommended that the
unit is secured to the
wall.
1. Move the unit into
desired position.
2. Mark the wall with a
suitable scribe the
position of the fixing
hole.
3. Drill hole and insert a
suitable Wall Plug,
Please check the type of wall
you are fixing to and for more
information please see the
guide to wall mounting
& Fixings on the back page
Warning:
Before driling,check
wall for hidden pipes
and cables.
4. Secure the strap to the
wall using a suitable
wall screw and washer G
Note: To hide the straps
behind the unit, drill the
holes lower than the top of
the unit
1. To Top Panel 1 fit
1 x Wall strap L as
shown using 1 x Washer
1
IG
Assembly Complete
and Screw H
H
G