AtGames BLAST WD3306 User manual

Wireless P2 Game Controller
The image below shows the location of the switches and buttons. Each function is outlined below.
(The illustration is for reference only. Certain controller functions are incompatible with some games.)
Appearance and Key List
Directional Pad (D-Pad)
Directional Pad for game playing.
Press the button to start the game and press it again to pause.
2
Power Indicator
Press any key and the indicator will light up if there
is still battery power left in the controller.
3
Power
Turn the controller’s power ON/OFF.
4
1START
ABC
XYZ
START
1
3
4
2
NOTE:
Button functions may vary
depending on game.
Find out more about Blast!™ at:
https://blast.atgames.net
HOW TO PLAY
TWO-PLAYER GAMES
Press START on
your P2 controller
to join the game.
Power on your
Blast! dongle.
Enter any 2-player game
using the P1 controller.
1 32
www.atgames.net
NOTE :
If a controller button has not been pressed for a while, the controller will enter standby mode.
Press any button to wake the controller from standby.
Each wireless controller requires 2 AAA batteries, not included.
How TO confirm the wireless controller
connects to the BLAST! HDMI dongle
Controllers from previous AtGames' consoles are not supported.
Insert two AAA batteries into
the back of the controller.
1
1Power on the system. Press any
button on the controller and it
will connect to the HDMI
dongle automatically.
The Power indicator light will
blink. Repeat for the second
controller.
23
When the power
indicator stops
blinking, you
have completed
pairing.
65
Turn the
controller’s
power on.
Turn the
controller’s
power off.
Plug the large end of the
USB cable into a USB
port or USB AC adapter
(not included) to turn on
the HDMI dongle.
Plug the small end
of the USB cable
into the Micro-USB
port on your HDMI
dongle.
4
NOTE : If the controller is not working, the batteries may have run out. Please change the batteries.
How To pair the controller with
the BLAST! HDMI dongle
31 2
Press and hold Game key
A and press Up on D-pad for
5 seconds until the power
indicator starts blinking
after completing Step 3.
2.4G WIRELESS
CONTROLLER
P2 CONTROLLER
WIRELESS

AtGames Digital Media, Inc. www.atgames.net
• Never try to short-circuit the battery terminals.
• Rechargeable batteries are to be removed from the device before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Do not charge non-rechargeable batteries.
• Batteries are to be inserted with the correct polarity as indicated inside the battery compartment.
• Do not mix old and new batteries. Do not mix batteries of different types: standard (carbon-zinc), alkaline, or rechargeable
(nickel-cadmium).
• Remove batteries during long period of non-use.
• Always remove dead batteries from the product.
• Dispose of batteries safely. Do not dispose this product or any batteries in a fire.
Battery Safety
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to
operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.

Forremoter
ThisequipmentcomplieswithFCCradiationexposurelimitssetforthforanuncontrolledenvironment.Thisequipment
shouldbeinstalledandoperatedwithminimumdistance0mmbetweentheradiatorandyourbody.Thistransmittermust
notbeco-locatedoroperatinginconjunctionwithanyotherantennaortransmitter.
ISED Statement
ThisdevicecomplieswithIndustryCanadalicense‐exemptRSSstandard(s). Operationissubjecttothefollowingtwo
conditions:(1)Thisdevicemaynotcauseinterference,and(2)Thisdevicemustacceptanyinterference,including
interferencethatmaycauseundesiredoperationofthedevice.
ThedigitalapparatuscomplieswithCanadianCANICES‐3(B)/NMB‐3(B).
LeprésentappareilestconformeauxCNRd'IndustrieCanadaapplicablesauxappareils
radioexemptsdelicence.L'exploitationestautoriséeauxdeuxconditionssuivantes:(1)l'appareilnedoitpasproduirede
brouillage,et(2)l'utilisateurdel'appareildoitacceptertoutbrouillageradioélectriquesubi,mêmesilebrouillageest
susceptibled'encompromettrelefonctionnement.
l'appareil numérique du ciem conforme canadien peut ‐3 (b) / nmb ‐3 (b).
Forremoter
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102
RF exposure, users can obtain Canadian information on RF exposure and compliance.
cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du cnr - 102 et conformité avec
rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur l'exposition aux champs rf et la
conformité.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 0mm between the radiator & your body.
Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrôlé. Cet
équipement doit être installé et utilisé à distance minimum de 0mm entre le radiateur et votre corps.
www.atgames.net