Atherton ADE-132W1 User manual

© 2015 Atherton Electronics Corp. All rights reserved.
CCTV LED MONITOR
MODEL: ADE-132W1
ADE-142W1
USER’S
MANUAL

© 2015 Atherton Electronics Corp. All rights reserved.
TABLE OF CONTENTS
FCC information ---------------------------------------------------------------------- 1
CE information ------------------------------------------------------------------------ 1
Safety Precautions ------------------------------------------------------------------- 2
1. Scope -------------------------------------------------------------------------------------- 3
2. Functional specification ------------------------------------------------------------- 3
3. Controls and indicators -------------------------------------------------------------- 5
4. OSD Menu --------------------------------------------------------------------------------8
5. Regulatory Agency ------------------------------------------------------------------- 19
6. Mechanical ----------------------------------------------------------------------------- 20
7. Wall mount notes-------------------------------------------------------------------------- 22

.
1
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables andA.C. power cord, if any, must be used in order to comply with
emission limits.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE INFORMATION
The product must be installed according to the currently valid installation regulations for
EMC to guarantee the designed use and to prevent EMC problems.
The device supplied with this manual is according to the EC, EMC Directive,
2004/108/EC & LVD 2006/95/EC

.
2
SAFETY PRECAUTIONS
1. Do not modify the three-prong grounding type monitor power plug in any way.
2. Operate this unit only from the type of power source indicated on the label.
3. Do not block or cover ventilation openings on the back or bottom of the monitor cabinet.
4. Do not place this monitor near a radiator or heating vent.
5. Do not push objects of any kind through cabinet openings. This may result in fire or
electrical shock.
6. Before adding attachments always ask a service technician to perform routine safety tests
to determine that equipment is in safe operating condition. Ground potential tests should
be part of the routine safety check made by the service technician.
7. Do not place monitor on an unstable cart, stand, or shelf where it may fall and injure
personnel or damage equipment.
8. Route power cords so that they cannot be walked upon or tripped over. Do not allow
anything to rest on the power cord.
9. Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not
spill liquid of any kind on the unit.
10.Unplug the power cord from the unit before cleaning the display. Use only a damp cloth.
Do not use alcohol, spirits, or ammonia to clean the display. DO NOT ATTEMPT TO
CLEAN THE INTERIOR OF THIS UNIT- THIS ACTION MUST BE PERFORMED BY THE
SERVICE TECHNICIAN AS REQUIRED DURING NORMAL MAINTENANCE.
11.Refer all servicing to qualified service personnel. REMOVAL OF BACK COVER BY
UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO DANGEROUS
VOLTAGES OR OTHER HAZARDS.
12.Unplug the unit immediately and notify the service technician.
A. If liquid has been spilled into the display or the display has been exposed to rain or
water.
B. If the unit has been dropped or the cabinet damaged.
C. If fuses continue to blow.
D. If the power cord is damaged or frayed.
E. If a distinct change from normal operation is apparent.
When replacement parts are required, be sure that the service technician uses components
specified by the manufacturer which have the same characteristics as the original parts.
UNAUTHORIZED SUBSTITUTIONS MAY RESULT IN FIRE, ELECTRICAL SHOCK OR
OTHER HAZARDS.
Upon completion of any service or repairs, ask the technician to perform safety checks to
determine that the equipment is in safe operating condition.
WARNING: SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVERS OF THIS
MONITOR. DO NOT OPEN THE COVERS UNDER ANY CIRCUMSTANCES,
THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE

.
3
1. Scope
This specification is used to define the performance of ADE-132W1 & ADE-142W1
series color LED monitor. This system also supports both video input and PC input. In video
input mode, the system can automatically detect the NTSC signal and PAL signal. In PC
mode, this system can support up to 1920 x 1080 VESA standard.
The user friendly OSD menu is also provided to make this system easy to operate.
2. Functional Specifications
2.1 Power Supply
The power supply spec is listed below,
AC INPUT
AC power input range：Rated voltage 100 –240 Vac +/- 10%, 47~63Hz,
2 Amps max.
* Power consumption：ADE-132W1: 65W max.; ADE-142W1: 80W max.
* Power efficiency：80% typical at normal line input and full load.
2.2 Video Characteristics
Composite Video (CVBS): 1.0 Vp-p (0.5 –1.5Vpp), Automatic switching from 75 unbalanced
termination to Hi-Z with loop-through operation.
Y/C (S-video): 1.0 Vp-p (0.5 –1.5Vpp), Automatic switching from 75 unbalanced termination
to Hi-Z with loop-through operation.
2.3 PC Input
VGA Input
Analog RGB: 0.707 Vp-p
Support VESA Standard Timing
HDMI Input
HDMI Compatible Interface
Digital Signal: TMDS
HDCP: HDCP 1.1
2.4 Audio Input
Signal Level: 1.0 Vrms

.
4
2.5 Environmental
Temperature
Operating: 0OC to +40OC; 32OF to 104OF
Storage: -20OC to +60OC; -4OF to 140OF
Humidity
Operating: 10% to 85% (non-condensing)
Storage: 10% to 95% (non-condensing)
2.6 EDID
This series of displays support EDID, but does not support DDC2B function.
2.7 Connectors
HA B C D E F G
A. HDMI INPUT: HDMI Connector
B. VGA INPUT: D-SUB 15 pins Connector
C. S-VIDEO (Y/C) INPUT: Mini-DIN 4 pins Connector
D. CVBS INPUT: BNC Connector
E. CVBS OUTPUT: BNC Connector
F. AUDIO INPUT: Phone Jack, Stereo
G. AUDIO OUTPUT: Phone Jack, Stereo
H. AC Input: Power cable (AC Power Plug IEC 320, C14)

.
5
Set up sequence
1. Make sure the power of PC and/or Video source were turned OFF.
2. Plug the Video signal or VGA or HDMI cable to monitor.
3. Plug the AC power cord onto monitor’s AC Socket, then turn power switch
ON (the POWER LED should lit steady RED).
4. Turns the PC and/or Video source power ON.
5. Press monitor’s power button to turn ON monitor power.
(Use reverse sequence to teardown the monitor)
3. Controls and indicators
ADE-132W1 & ADE-142W1 MONITOR
A. “” Power button
Press the button to turn ON or turn OFF the monitor.

.
6
B. “”Source button
Press the button to show source menu. Select from CVBS, S-Video, VGA and HDMI
input signal.
C. “ ”Menu button
Press the button to show the OSD main menu.
As a confirmation key during the OSD operation.
D. “ ”UP buttons
Press the button to scrolling the cursor to desired function.
E. “ ”Down button
Press the button to scrolling the cursor to desired function.
F. “ ”Volume+ buttons
Press the button to increase volume.
Press the button to increase the value of selected function in sub OSD menu.
G. “ ”Volume- button
Press the button to decrease volume.
Press the button to decrease the value of selected function in sub OSD menu.
H. Power Switch
Press the Switch to turn ON or turn OFF the monitor Power.
POWER LED Indication
Green - Power ON
LED light OFF - Power switch OFF
Red - Power OFF
Red + Flash Green - Sleep mode (VGA mode only)
POWER LED
IR Receiver

.
7
Remote control
Power: Power On or Off the monitor
Mute: Mute the audio
Key Lock: Lock and unlock push buttons
Menu/ Left/ Right/ Up/ Down/ OK/ Exit:
Monitor OSD control
: Hot key for volume control
VIDEO: Select CVBS source
S-VIDEO: Select S-Video source
Info: Display Monitor source information
HDMI: Select HDMI source
VGA: Select VGA source
SDI: Reserve
Auto: VGA mode picture Adjust

.
8
4. OSD Menu
Hot key：
Quick adjust keys from front panel hot keys：
VOLUME：
Press or button to select the function and press / button to adjust the
volume, then press MENU button to exit OSD menu.
KEY LOCK：Press and hold MENU key for 6 sec. to enable key lock.
KEY UN-LOCK：Press and hold MENU key for 6 sec. to disable key lock.

.
9
VGA & HDMI mode：
OSD Menu structure：
Use the Source button to select from CVBS, S-VIDEO, VGA or HDMI, the menu structure
within each source varies, refer to sections below on how to set-up each option.
VGA / HDMI mode：
Press the Menu button to bring up the MAIN MENU Page. The following page will appear.
Press /button to select an icon, then Press MENU button to change the value in the
sub menu.
VGA MAIN MENU
HDMI MAIN MENU

.
10
MAIN ADJUST：
1. Press / button to select an icon
2. Press MENU button to select item
3. Press / button to adjust the value
4. Press MENU button to return
VIVID MODE：Select the VIVID MODE (0~3 and USER)
USER, 0: TEXT, 1: PHOTO, 2: MOVIE, 3: GAME
BRIGHTNESS：Adjust the brightness value
CONTRAST：Adjust the contrast value
VOLUME：Adjust the volume
EXIT：Press MENU button to return to the main menu

.
11
COLOR ADJUST：
Set the color temperature of the LCD monitor for the CIE coordinate 9300˚k or 6500˚k
or USER MODE
1. Press / button to select an icon
2. Press MENU button to select adjust item
3. Press / button to adjust the value
4. Press MENU button to return
USER COLOR：Adjust the color temperature
RED：Adjust the RED value for user mode
GREEN：Adjust the GREEN value for user mode
BLUE：Adjust the BLUE value for user mode
EXIT：Press MENU button to return to the main menu

.
12
IMAGE ADJUST (VGA ONLY)：
1. Press / button to select an icon
2. Press MENU button to select adjust item
3. Press / button to adjust the value
4. Press MENU button to return
AUTO ADJUST：Press MENU buttons to auto adjust the H. Position,
V. Position, Phase, Clock
H. POSITION：Adjust the horizontal position value
V. POSITION：Adjust the vertical position value
PHASE：Adjust the phase value
CLOCK：Adjust the clock value
EXIT：Press MENU button to return to the main menu
INFORMATION：
Press MENU button to get the VGA timing information

.
13
LANGUAGE：Press MENU button to enter the sub-menu
1. Press / button to select language
2. Press MENU button to enter
SETUP MENU：
1. Press / button to select an icon
2. Press MENU button to select adjust item
3. Press / button to adjust the value
4. Press MENU button to return
OSD TIMEOUT：Adjust the OSD Show time (5 ~120 sec)
GREEN MODE：Off or On (5 min~10 min)
OFF –No function
ON –Screen will reduce back light to 80% within (5 min to 10 min)
Screen will back to normal when any button is being touched

.
14
AUTO SHIFT：Adjust AUTO SHIFT ON/OFF
OFF –No Function
ON –Every one hour there will be one scan line from top to bottom ( Every 1 second
down one scan line) to prevent panel image sticking
EXIT：Press MENU button to return to the main menu
RECALL：
Brightness, Contrast, Volume, Vivid Mode, OSD Timeout, Green Mode, Auto Shift
return to default Value
Anti-Burn-inTM scan line

.
15
Video mode (CVBS & S-Video)：
Press the Menu button to bring up the MAIN MENU Page. The following page will appear.
Press / button to select an icon, then Press MENU button to change the values in the
sub menu.
MAIN ADJUST：(VIDEO & HDMI MODE)
1. Press / button to select an icon
2. Press MENU button to select item
3. Press / button to adjust the value
4. Press MENU button to return

.
16
VIVID MODE：Select the VIVID MODE (0~3 and USER)
USER, 0: TEXT, 1: PHOTO, 2: MOVIE, 3: GAME
BRIGHTNESS：Adjust the brightness value
CONTRAST：Adjust the contrast value
SHARPNESS：Adjust Image sharpness
SATURATION：Adjust Image saturation
TINT：adjust Image tint (NTSC only)
VOLUME：Adjust the volume
EXIT：Press MENU button to return to the main menu
COLOR ADJUST：
Set the color temperature of the LCD
monitor for the CIE coordinate 9300˚k or 6500˚k or USER MODE
1. Press / button to select an icon
2. Press MENU button to select adjust item
3. Press / button to adjust the value
4. Press MENU button to return
USER COLOR：Adjust the color temperature
RED：Adjust the RED value for user mode
GREEN：Adjust the GREEN value for user mode
BLUE：Adjust the BLUE value for user mode
EXIT：Press MENU button to return to the main menu

.
17
SCAN SETTING：
1. Press MENU button to select the sub-menu
2. Press / button to select Scan Setting state.
3. Press MENU button to return
INFORMATION：
Press MENU button to get the timing information
LANGUAGE：Press MENU button to enter the sub-menu
1. Press / button to select language
2. Press MENU button to enter

.
18
SETUP MENU：
1. Press / button to select an icon
2. Press MENU button to select adjust item
3. Press /button to adjust the value
4. Press MENU button to return
OSD TIMEOUT：Adjust the OSD Show time (5 ~120 sec)
GREEN MODE：Off or On (5 min~10 min)
OFF –No function
ON –Screen will reduce back light to within (5 min to 10 min)
Screen will back to normal when any button is being touched
AUTO SHIFT：Adjust AUTO SHIFT ON/OFF
OFF –No Function
ON –Every one hour there will be one scan line from top to bottom
(Every 1 second down one scan line) to prevent panel image sticking
3:2 PULL DOWN : Select ON/OFF of 3:2 pull down
EXIT：Press MENU button to return to the main menu
RECALL：
Brightness, Contrast, Sharpness, Saturation, Tint, Volume, Vivid Mode, OSD Timeout,
Green Mode, Auto Shift return to default Value
AUTO SHIFT Scan line