Atlanta ATH-856 User manual

RUS
EN
UA
Инструкция по эксплуатацииInstruction ManualIнструкцiя з експлуатацiiVer.2.06.2010ATH-856Hair clipper setНабор для стрижкиНабір для стрижки

2
HAIR CLIPPER SET / НАБОР ДЛЯ СТРИЖКИ / НАБІР ДЛЯ СТРИЖКИ

3
INSTRUCTION MANUALDEAR CUSTOMER!WE CONGRATULATE YOU WITH THE RIGHT CHOICE! YOU HAVE BECOME AN OWNER OF ‘ATLANTA’ TRADE MARK PRODUCTION, FAMOUS FOR PROGRESSIVE DESIGN AND GOOD PERFORMANCE QUALITY. WE HOPE THAT OUR PRODUCTION WILL BECOME YOUR COMPANION FOR YEARS.CAUTION:DO NOT PLACE THE DEVICE CLOSE TO SUCH HEAT SOURCES AS: HEATING RADIATORS, GAS FRYERS; OR IN THE PLACES SUBJECT TO DIRECT SUNLIGHT, EXCESSIVE DUST, MECHANICAL VIBRATION, OR IMPACT LOADS. DO NOT COVER THE DEVICE. PULL OUT THE PLUG TO DISCONNECT THE POWER CORD. NEVER PULL THE CORD. AVOID ENTRANCE OF WATER OR OTHER LIQUIDS INTO THE HAIR CLIPPER: THIS CAN RESULT IN ITS DAMAGE. AFTER SHIPPING UNDER LOW TEMPERATURE CONDITIONS, DO NOT PLUG IN THE DEVICE UNTIL IT STAYS IN A WARM ROOM FOR TWO HOURS. DO NOT USE REACTIVE LIQUIDS (GASOLINE, KEROSENE, ALCOHOL, AND VARIOUS SOLVENTS) TO CLEAN THE DEVICE. DO NOT USE THE DEVICE WITH UNLUBRICATED BLADES. AVOID COMPLETE DISCHARGE OF THE ACCUMULATORS.ATTENTION!IN ORDER TO PREVENT FROM INFLAMMATION OR ELECTRIC INJURY, DO NOT EXPOSE THE ELECTRICS OF THE DEVICE TO RAIN OR MOISTURE. DO NOT SUBMERGE THE DEVICE IN WATER OR OTHER LIQUID. IN ORDER TO AVOID AN ELECTRIC SHOCK, DO NOT TRY TO OPEN THE HOUSING WITHOUT ASSISTANCE. APPLY FOR MAINTENANCE TO A SKILLED SPECIALIST ONLY.

4
INSTRUCTION MANUALMAJOR COMPONENTS OF THE SETA - housingB - handleC - start buttonD - blade adjusting screw (optional)E - lever to adjust the bladesF - bladesG - blades cover H - hanging loopI - power cordJ - nozzles K - scissors L - comb M - cleaning brushN - blade lubricating oilPERFORMANCE SPECIFICATIONSVoltage:
230V~ 50Hz
Rated power: 9WOperating time: 30 minutesType: VibrationalWidth of blade: 45 mmLength hairstyle: 0,7-2mm (blade), 3-12mm (attachment)Operating life: 3 yearsDimensions: 19.5 x 5.8 x4.5 cmWeight: 0.370 kgManufacture date is shown in the product serial number: the third and the forth digit is the manufacture month and the fifth one is the manufacture year (from 2010 to2019) Example: хх120ххххххх – 12 month, year 2010.MAINTENANCEThe hair clipper requires a regular lubrication of blades to ensure its proper and continuous operation. Use a small amount of oil (1 drop) supplied with the device BEFORE USINGPlease, read the manual carefully prior to start of service of the device.

5
INSTRUCTION MANUALfor lubrication. After lubrication, switch on the device to distribute the oil and then remove surplus oil with a cloth. It is necessary sometimes to remove blades to clean hair clipper well. Please remember the position of blades to each other, as the lower blade is adjusting and can be installed in different positions. This model can be fitted with a screw adjustment of the blades. If the hair clipper does not cut well, it is necessary to unscrew slightly counter-clockwise this screw. If the hair clipper is too much noise, you need to tighten a little bit this screw clockwise.HAIR CLIPPER OPERATION1. Check if the device requires lubrication. Charge the device completely. 2. Plug in the machine to the mains.3. Remove the protective cover to the clipper blades. Please hold it to the handle, do not touch the blades by hand all the time it is plugged.4. If you need set one of the four nozzles, which allow to receive as a result of cutting the hair of varying lengths.The attachment is recommended to be set in the position enabling to leave the longer hair; if required, the position for leaving the shorter hair can be set later.5. Set the switch (C) into the forward position and start clipping. Change the attachments only when the device is switched off.6. If you need a length exceeding 12 mm, remove the attachment and use the comb, or adjust the length with the fingers of your free hand.7. Firstly, handle a small section of hair to get used to the length of the hair being cut. Start to clip from the occipitals and at the sides, then clip in the front moving to the crown; all the movements should be performed against the hair growth direction.