Atlantic Boilers ME STANDARD 90 Installation and operation manual

ME STANDARD
ELECTRIC BOILER
OPERATING & MAINTENANCE MANUAL
MODELS - 90 - 120 - 150 - 180 - 210 - 245 - 280 - 315 - 350 - 385 - 420
455 - 490 - 525 - 560 - 595 - 630
09/2011 CODE: 560955 CE Direcve 2006/95/CEE
Brish Standard EN 60335-1 (C 73800)

2ME Standard Manual
CONTENTS
1.0 INTRODUCTION
1.1 Description 3
1.2 Performance 4
1.3 Dimensions 4
1.4 Electrical power requirements 4
1.5 Drawings 5
1.6 Orientation 6
2.0 INSTALLATION
2.1 Procedure 7
2.2 Essential accessories 7
2.3 Typical Arrangement 8
2.4 Precautions 9
2.5 Boiler room arrangements 10
2.6 Commissioning 10
3.0 ELECTRICAL ARRANGEMENTS
3.1 Control panel arrangement 11
3.2 Control circuitry 12
3.3 Electrical power circuitry 13
3.4 Fuse and overload protection 13
3.5 Electrical circuit 14
3.6 Termination connection drawing 14
3.7 Operation of the digital controller 15
3.8 Alarm signals 15
4.0 DELIVERY and OFF-LOADING 16
5.0 MAINTENANCE 16
6.0 IDENTIFICATION OF SPARE PARTS 17
7.0 FAULT DETECTION 17
GUARANTEE 18
DECLARATION OF CONFORMITY 19

3
ME Standard Manual
1.0 INTRODUCTION
1.1 Description
The ME STANDARD electric boiler is suitable for a variety of types of space heating and indirect
domestic hot water – covering sealed circuits from 0.5BARS to 7.0BARS working pressure.
The ME STANDARD electric boiler electric boiler always requires earthing, under protection
index IP21/1K 08.
The ME STANDARD electric boiler electric boiler is designed and manufactured according to the
following :-
• EN Decree 95-1081 – control of boiler materials and electrical supply voltage used in
order to conserve the safety of persons and animals which might be in the vicinity
• European Directive 2006/95/CEE covering low voltage system application
• BS EN 60335-1 class C73800, part 1, general rules
THE STANDARD ELECTRIC BOILER
• Outputs from 90kW to 630kW
• Outputs above 630kW to 980kW by special order
• Maximum working pressure 4BARS, test pressure 6BARS
• Maximum working temperature 100°C, limit 110°C
• 50mm thick glass silk insulation with MO re classication cladding
• Hand reset limit thermostat at 110°C
• Resistance to earthing shock not less than 1 megohm
INCOLLOY IMMERSION HEATERS – 90kW to 180kW boilers
• Individual heater elements 80-200mm diameter
• Individual elements – 30kW, 415V, 3phase & earth
• Vertical access requirement – 2010mm
INCOLLOY IMMERSION HEATERS – 210kW to 630kW
• Individual heater elements 80-200mm diameter
• Individual elements – 35kW, 415V, 3phase & earth
• Vertical access requirement – 2050mm
CONTROL PANEL
• Control cabinet xed to the boiler
• Enabling from remote electronic or hand operation
• Three cartridge fuses per each step control
• Three contactors, one per step
• One transformer for the control circuit
• One main isolator with manual lock
• One ‘alive’ lamp indicating power on
• One ‘lock-out’ lamp indicating boiler stopped
• One digital controller
• One set of terminal connections
• The control panel can
(i) be located in any of three positions on the boiler
(ii) have the panel door in either of two hinge positions
(iii) be provided with variable control & output

4ME Standard Manual
MODEL 90 120 150 180 210 245 280 315 350 385 420 455 490 525 560 595 630
Maximum Output kW 90 120 150 180 210 245 280 315 350 385 420 455 490 525 560 595 630
Eciency  % 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9 99.9
No of Immersion heaters 3 4 5 6 6 7 8 9 10 11 12 13 14 15 16 17 18
Minowrate l/sec 0.6 0.8 0.8 1.1 1.7 1.7 1.7 1.7 2.2 2.2 2.2 2.8 2.8 2.8 2.8 3.6 3.6
Maxowrate l/sec 5.0 5.0 10.0 10.0 11.7 11.7 11.7 11.7 11.7 11.7 11.7 19.4 19.4 19.4 19.4 19.4 19.4
Max pressure drop kPA 8 8 8 8 16 16 16 16 16 16 16 16 16 16 16 16 16
Flow/return connections mm 80 80 80 80 100 100 100 100 100 100 100 150 150 150 150 150 150
Dryweightkgs 117 121 125 129 233 238 243 248 253 258 263 367 372 377 382 387 392
Water content litres 128 128 128 128 283 283 283 283 283 283 283 395 395 395 395 395 395
Totalweight kgs 280 285 295 320 430 435 450 460 505 510 520 650 650 650 670 670 690
MODEL 90 120 150 180 210 245 280 315 350 385 420 455 490 525 560 595 630
Depth  mm 1030 1030 1030 1030 1180 1180 1180 1180 1280 1280 1280 1360 1360 1360 1360 1360 1360
Width  mm 600 600 600 600 800 800 800 800 1000 1000 1000 1000 1000 1000 1000 1000 1000
Height  mm 1380 1380 1380 1380 1570 1570 1570 1570 1700 1700 1700 1900 1900 1900 1900 1900 1900
Access above mm 900 900 900 900 1100 1100 1100 1100 1100 1100 1100 1100 1100 1100 1100 1100 1100
Access front mm 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000
Access rear mm 750 750 750 750 750 750 750 750 750 750 750 750 750 750 750 750 750
Access side mm 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500
Accessotherside mm 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100 100
MODEL 90 120 150 180 210 245 280 315 350 385 420 455 490 525 560 595 630
OUTPUT STEP ONE
Power  kW 30 60 60 60 70 105 105 105 140 140 140 175 175 175 210 210 210
Fuse amps 63 125 125 125 125 160 160 160 250 250 250 315 315 315 400 400 400
OUTPUT STEP TWO
Power  kW 30 30 60 60 70 70 105 105 140 140 140 175 175 175 175 175 219
Fuse amps 63 63 125 125 125 125 160 160 250 250 250 315 315 315 315 315 400
OUTPUT STEP THREE
Power  kW 30 30 30 60 70 70 70 105 105 105 140 140 140 175 175 210 210
Fuse amps 63 63 63 125 125 125 125 160 160 160 250 250 250 315 315 400 400
1.2 Perfomance
1.3 Dimensions
1.4 Electrical Power Requirements 415volts,3phase,50Hz

5
ME Standard Manual
MULTI ELEC - STANDARD DN650 - 455- 630kW
Ø33/42F
455 - 630kW
F
D E
HT
Base
Flow ØA
Return ØA
MULTI ELEC STANDARD DN550 210-420KW
Scale 1:15
MODEL 210 245 280 315 350 385 420
Maximum Output kW 210 245 280 315 350 385 420
Eciency % 99.9 99.9 99.9 99.9 99.9 99.9 99.9
No of Immersion heaters 6 7 8 9 10 11 12
Min ow rate l/sec 1.7 1.7 1.7 1.7 2.2 2.2 2.2
Max ow rate l/sec 11.7 11.7 11.7 11.7 11.7 11.7 11.7
Max pressure drop kPA 16 16 16 16 16 16 16
Flow/return connections 100 100 100 100 100 100 100
Dry weight kgs 233 238 243 248 253 258 263
Water contents litres 283 283 283 283 283 283 283
DIMENSIONS
Depth mm 970 970 970 970 1070 1070 1070
Width mm 670 670 670 670 670 670 670
Height mm 1570 1570 1570 1570 1600 1600 1600
Access above mm 1100 1100 1100 1100 1100 1100 1100
Access front mm 1000 1000 1000 1000 1000 1000 1000
Access rear mm 750 750 750 750 750 750 750
Access side mm 500 500 500 500 500 500 500
Access other side mm 100 100 100 100 100 100 100
Base
210 -315kW
350-420kW
Flow
Return
Height
1.5 Drawings

6ME Standard Manual
1.6 Orientation

7
ME Standard Manual
2.0 INSTALLATION
2.1 Procedure
- Position the boiler squarely on the prepared base
- Fit the correct accessories to the boiler connections
- Connect the boiler to the pipework system
- Connect the boiler to the isolated electrical supply
- Fill the boiler with fresh, clean water
- Check that the immersion heaters are electrically isolated from the boiler. If the isolation
is less than 2mega-ohms, the bridge must be found and rectied.
- Check the operation of the main control panel isolator, and of the overloads serving the
immersion heaters
- Check the operation and the correct direction of rotation of the circulating pump
- Check, with the circulation pump stopped, that the water ow switch over-rides the
immersion heaters through their relays and also brings on the relevant alarm light
- Check the setting and operation of the immersion heater step controls
- Switch o the immersion heaters using the main control panel isolator
- Check that all the cartridge fuses are sound
- Doublecheckthatalltheimmersionheatersreceivethecommonvoltage.
 Repeatthecheckafterseveralhoursrun.
 Anydefectinvoltagecandestroytheheatersandinvalidatetheguarantee.
2.2 Essential
Accessories
Thefollowingitemsarerequired:-
A. One automatic air vent with isolating valve
B.One 4-bar safety valve and one 7 bar
temperature and pressure relief valve
C. One shunt pump
– protected by overloads
(0.37A to 1.4A adjustable)
and run + fault lamps
D. Dierential pressure switch
E. One drain ball valve
F. One water ow switch
B. safety valve
temperature and
pressure relief valve
C
F. water ow
switch
E drain ball valve.
RECOMMENDED WATER FLOW SETTINGS (l/sec)
Pipeline sizes: mm 32 40 50 65
Minimum range: 0.35-0.47 0.53-0.72 0.61-0.83 1.0-1.4
Maximum setting 1.0 1.6 1.9 3.2
A. automatic
air vent
D.
Dierential
pressure
switch
C.
shunt
pump

8ME Standard Manual
ME STANDARD Typical Circuit
Dierential pressure switch
TEL: [phone] EMAIL: [e-mail] WEB: www.atlanticboilers.com Box 11, Ashton Under Lyne, LANCS 0L6 7TR
DP
Ball Valve
Expansion
Vessel
WF
DP
Dierential
pressure switch
Pressure
Relief
Valve
Drain
Valve
Filling Loop
Ball Valve
Heating
Ball ValveStrainerPump
Non return
valve
Drain
Valve
Expansion
Vessel Pressure
Relief
Valve
Filling
Loop
Auto top-up system
Water
ow switch
Temperature
and pressure
relief
Ball Valve
Safety
Valve
WF
IMPORTANT
INSTALLATION DETAIL FOR WATER FLOW SWITCH
A A
Flow
S w it ch
T - P ipe
Flow
'A' must be more t han 5 t im e s o f t he p ipe d iamete r
Flow
ME STANDARD
Electric Boiler
2.3 Typical Arrangement

9
ME Standard Manual
2.4 Precautions
TheMulti-elecStandardrequiresaninstallationconformingto:
• Directive 2009/125/CE (Eco-Design)
• Directive 2010/30/UE (Energy Labelling)
• Directive 2014/35/UE (Low Voltage)
• Directive 2014/30/UE (Electromagnetic compatibility)
• Directive 2014/68/UE (Pressure equipment directive)
• The electric boilers operate at more than 99.5%GCV eciency
• They require minimal maintenance, are silent & are compact.
• With wind or water electric generation, they use green energy.
Toreleasealargeamountofheattowaterheatingsystems:
A: They need a minimum static water pressure of 1 BAR when cold. When hot, this pressure will
rise and must not exceed 6 BARS for the normal boiler (higher pressures available)
B: They need a minimum water ow rate which is given in the boiler manual. Atlantic Boilers
oer a shunt pump set for each boiler which is tted in the same pipe line as the boiler. The
pump will exceed the minimum water ow rate.
C: They must not exceed maximum water ow rate which is given in the boiler manual.
D: In case the pump fails or a valve is closed, Atlantic Boilers oer a water ow switch tted
in the same pipeline as the boiler and set to just below maximum ow. If the switch registers
maximum ow, the boiler stops
E: We recommend an automatic pressurisation unit, with low and high pressure limits to
safeguard the electric boiler via its control panel. The unit will include a fast-ll loop to
initially ll the system.
F: The system should be isolated, ushed, lled and treated separately from the boiler.
Fill the boiler with clean, pure water only.
DetailedwatertreatmentofMulti-elecelectricboilersttedwith
adjoiningbalancing*sedimentationvessel
• Filling the outgoing secondary through the BSV pipework, the water can be variable due to its
source and it can be aggressive. It may need neutralisation by chemical additives or even the
use of Plate Heat Exchanger to divide the system out.
• The secondary water needs to be introduced though the BSV drain point or cold feed point.
• The electric boiler(s) need clean pure water introduced from the boiler drain valves
• The strainers, tted in the secondary, need to be tted in returns to the BSV where they
capture the most part of the deposits.
• The strainers, tted in the boiler returns, need to be of ne extended secondary circuits,
mesh, to capture any overow of deposit from the secondary circuits.

10 ME Standard Manual
2.5 Boiler room arrangements
TheMulti-elecStandardmustbeinstalled:
• In an adequately-ventilated boiler room with ambient temperature below 30°C
and relative humidity maintained between 30% and 80% and where condensation
does not occur
• In a non-corrosive atmosphere
• In a non-explosive atmosphere
• Where there is good access to the boiler position for installation and maintenance
• Where there is good access for delivery, o-loading and positioning
• Using similar materials in the in the pipework, and avoiding materials leading to electrolytic
action and system deterioration
The Multi-elec Compacte is not suitable for external installation
2.6 Commissioning
• The boiler must be completely full of water before the heating elements are switched on.
To ensure 100% lling, manual and automatic vents must be in eective positions where
complete air clearance can be guaranteed.
• The boiler can be lled with water by connecting a ll hose to the boiler drain valve and partly
opening the valve.
• The boiler safety valve can also be used rstly to vent the boiler at lling and, secondly,
ensuring the blow-down facility of the valve is clear in case of use.
• Commissioning is recommended by Atlantic 2000 or an authorised engineer for
Atlantic equipment.

11
ME Standard Manual
3.0 ELECTRICAL
ARRANGEMENTS
3.1 Control Panel Arrangement
KA1 CONTROL
RELAY
TERMINALS
T1/T2/T3STAGE
DELAY TIMERS
F1 TRANSFORMER
SUPPLY FUSES
F2 230V FUSES
415V MAINS
ISOLATOR
F6 STAGE 3 FUSES
F5 STAGE 2 FUSES
KM2 STAGE 2
CONTACTOR
KM3 STAGE 3
CONTACTOR
VOLTAGE SENSOR
400/230/115V
TRANSFORMER
F3 115V FUSES
F4 STAGE 1 FUSES
KM1 STAGE 1
CONTACTOR

12 ME Standard Manual
9
3.2) Control circuitry
EXTERNAL CONTROLS
3.2 Control Circuitry

13
ME Standard Manual
10
3.3) Electrical powercircuitry
3.3 Electrical power circuitry
MODEL 90 120 150 180 210 245 280 315 350 385 420 455 490 525 560 595 630
OUTPUT STEP ONE 30 60 60 60 70 105 105 105 140 140 140 175 175 175 210 210 210
OUTPUT STEP TWO 30 30 60 60 70 70 105 105 140 140 140 175 175 175 175 175 219
OUTPUT STEP THREE 30 30 30 60 70 70 70 105 105 105 140 140 140 175 175 210 210
Fuseratingsandtype:– industrial cylindrical cartridge
MODEL 90- 280kW
FUSES F1 1A type aM, F2 – 1A type gG, F3 – 0.5A type gG
MODEL 90- 280kW
FUSES F1 1A type aM, F2 – 1A type gG, F3 – 0.5A type gG
FUSES F4-F6 Type 22 x 58 : 63A type gG
Type 0 : 125A type gG
Type 1 : 160A type gG
Type 2 : 250, 315 & 400A type gG
Amperage requirement – insert table from earlier
3.4 Fuse and overload protection

14 ME Standard Manual
3.5 Electrical Circuit
Electrical circuit
• The Standard electric boiler must be provided with 415volts and without neutral wiring
• The electrical wiring cables must be sized by a qualied electrician in order to conform to
BS C 15100 and satisfying load, length of run and prevention of short circuit.
• The installation must be tested for automatic power failure in the
event of emergency power cut, heater lock-out or error in the neutral layout.
• All electrical equipment shall satisfy IP21/IK08 Class 1
• The immersion heaters shall only receive electrical power if they are fully immersed in water;
otherwise the guarantee on the heaters will not apply
ALL ELECTRICAL WIRING MUST BE CORRECTLY EARTHED
3.6 Terminal connection drawing
12

15
ME Standard Manual
3.7 Operation of the digital controller
Factory settings (primary heating circuit)
Flow temperature – 80degC
Maximum ow temperature setting – 95degC
Minimum ow temperature setting - 20degC
Time delay T1 – 30 seconds
Time delay T2 - 1 minute
Time delay T3 - 2 minutes
digital controller has numbers or message, touch settings
+ – touch raise settings, – touch lower settings
1. The Panel has a registration label
2. The wiring is capable of a maximum current of 23kA
3. Neutral panel wiring is not required
4. The Panel is protected by isolators, circuit breakers and fuses.
5. Earth wiring is essential
6. One week after commissioning, all connectors – on immersion
heaters and incoming electrical supplies – need to be checked.
This should be repeated annually.
7. Manufacturing tests include heat output and control circuitry
8. The boilers should not be installed or operated in corrosive,
explosive or humid atmosphere
9. Adequate natural ventilation is required. 550mm2 x kW free
area at high and low level is recommended
LOCK OUT
MULTI ELEC STANDARD
ATLANTIC BOILERS
TEL: [phone]
2000
80
RUN
STOP
POWER ON
PGM EXIT
51 2
75
KW
K1 K2
K3
3.8 Alarm Signals
On Alarm, light (7) shows and the following messages appear on (1)
< PFO > Lock-out or power cut
< HA > High temperature lock-out
< LA > Low temperature alarm

16 ME Standard Manual
4.0 DELIVERY/OFF-LOADING
It is recommended that the STANDARD electric boiler is
transported and, if necessary, stored on the pallet on which
it is delivered from the factory.
If temporarily stored, the surroundings should be
maintained at temperatures below 80°C, and without
condensation at relative humidities between 30% and 80%
Manhandling the STANDARD electric boiler into position
requires :-
(a) Qualied, skilled manpower
(b) Use of a pallet trolley or a fork lift truck
(c) Use of the lifting eyes provided on the boiler and tested
of lifting beams
5.0 MAINTENANCE
Eectivemaintenancemustaimatpreventing:-
a). a reduction in the movement of water circulation through the boiler - this can result in the
formation of sediment or limescale on the boiler immersion heater elements
b). pockets of high temperature water across the boiler immersion heater
elements – resulting in their destruction by overheating
c). accumulation of sediment or limescale within the boiler, particularly on
or around the boiler immersion heater elements – overcoming these developments by the
introduction of fresh, clean water without any inhibitor or de-scaling agent
Minimum maintenance periods
A)Monthlymaintenance
i) Check operation of the automatic air vent
ii) Check operation of the water ow switch
iii) Check operation of the safety valve
B) Annual maintenance
i) Carry out the monthly checks
ii) Check all the electric control functions
iii) Check all pipework joints are water-tight
iv) Drain o small amount of boiler water content and check for condition
C).4-yearlymaintenance
i) Carry out the annual maintenance
ii) Isolate the boiler safely from all services
iii) Drain the boiler of water and open up for inspection
iv) Check for all maintenance requirements and remedy as necessary
v) Close and seal the boiler, ll with fresh clear water through drain outlet
vi) Pressure test, then repeat annual maintenance procedure
14
4) DELIVERY and OFF-LOADING
It is recommended that the STANDARD electric boileris transported and, if necessary,
stored on the pallet on which it is delivered fromthe factory.
If temporarily stored, the surroundings should be maintained at temperatures below
80degC, and without condensation at relative humidities between 30%and 80%
Manhandling the STANDARD electric boiler into position requires :-
(a) Qualified, skilled manpower
(b) Use of apallet trolley orafork lift truck
(c) Use of the lifting eyes provided on the boilerand tested of lifting beams

17
ME Standard Manual
07 SPARES
Controller 790220
Flow sensor 583027
30kW immersion heater 2534
35kW immersion heater 2536
Limit thermostat 581104
Water ow switch 480230
08 FAULT DETECTION
Beforemakinganyphysicalcheck,switchothepower
FAULT CHECK
The ‘live’ light is out Check for incoming power
Check fuses F1 and F2
Check the ‘live’ bulb
………………………………………………………………………………………………………………………..
The controller screen is out Check fuse F3
………………………………………………………………………………………………………………………….
Step 1 or Step 2 light is out Change the bulb
………………………………………………………………………………………………………………………….
The ‘red’ light is lit Check the limit thermostat
Check the water ow switch action
Check the circulating pump overload
…………………………………………………………………………………………………………………………..
If the fault remains Call in a qualied service engineer

18 ME Standard Manual
17
7). IDENTIFICATION OFSPARE PARTS
Controller 790220
Flowsensor 583027
30kW immersion heater 2534
35kW immersion heater 2536
Limit thermostat 581104
Waterflow switch 480230
8). FAULT DETECTION
Before making any physical check, switch off the power
FAULT CHECK
The ‘live’ light is out Checkforincoming power
Check fuses F1 and F2
Check the ‘alive’ bulb
………………………………………………………………………………………………………………………..
The controllerscreen is out Check fuse F3
………………………………………………………………………………………………………………………….
Step 1 orStep 2light is out Change the bulb
………………………………………………………………………………………………………………………….
The ‘red’ light is lit Checkthe limit thermostat
Checkthe waterflow switch action
Checkthe circulating pump overload
…………………………………………………………………………………………………………………………..
If the fault remains Call in aqualified service engineer
This GUARANTEE is to the PURCHASER of the Boiler(s) who is deemed to be the INSTALLER of the
Boiler(s). If the Boiler(s) is(are) purchased by the EVENTUAL USER who then arranges to install the
Boiler(s), the EVENTUAL USER is deemed to be the INSTALLER. The details of the GUARANTEE are
given to assist the INSTALLER in obtaining eective action within the GUARANTEE and they are
in addition to the INSTALLER’S Legal Rights under the relevant statutory enactments for the time
being in force in England, Scotland, Wales and Northern Ireland.
GAS, OIL, B100 bio-diesel or ELECTRICAL EQUIPMENT
The Replacement or Repair of the item, including the Cost of its Delivery to the site of the
installation or its equal, provided that the Defect or Flaw occurs within one Calendar Year of the
Commissioning Date.
REMOVABLE COMPONENTS OF THE BOILER ASSEMBLY
(other than the gas, oil or electrical equipment)
The Replacement or Repair of the item, including the Cost of its Delivery to the site of
the installation, provided that the Defect or Flaw occurs within one Calendar Year of the
Commissioning Date.
THE MAIN BODY OF THE BOILER
The repair of any Defect or Flaw in the Main Body of the Boiler including any necessary removal or
replacement of that part of the Boiler on site if the Defect or Flaw occurs within ve calendar years
of the Commissioning Date
DEFINITIONS
The eective actions stipulated in this guarantee are subject are subject to the PURCHASER
complying completely with the following :-
1. The Boiler(s) is(are) installed according to the Recommendations of the Atlantic Boilers’ Manual,
the Recommended Codes of Practice of the CIBSE, the BSI, the BSRIA. and the Atlantic Boilers’
Commissioning Check List.
2. The Commissioning of the Boiler(s) by an Atlantic Engineer employed or authorised by
Atlantic Boilers, and regular servicing & maintenance according to the Atlantic Boilers’ Manual
& Service Booklet.
3. The Payment in Full by the Purchaser, unless otherwise agreed, of the invoices for the Supply
of the Boiler(s) as agreed, and the invoices for commissioning and any correction of installation
error, all to be made within agreement terms.
4. The Presentation at the time of a Claim under the Guarantee, of the Boiler Registration
number, the Commissioning Record and the necessary information for dening any
Replacement Part.
5. When a Replacement Part is supplied for a Defective Item, the Defective Item must be returned
to Atlantic Boilers at their Head Oce within 6 weeks of the Date of Notication of the Defect
and must be carefully labelled with Registration Number of the Boiler together with the Name
and Order Reference of the Purchased of the Boiler. If this is not complied with, the Purchaser
will be charged with the Cost of the Item and its Delivery.
11/05/2015.MW
ATLANTIC 2000 - boilerplant sales ACM ATLANTIC - commissioning and maintenance ATLANTIC 4422 – spares
Registered in England. Company No: 1477687 Vat Reg No: 306 0653 89 Tel: [phone] Fax: [phone]
GUARANTEE

19
ME Standard Manual
We Harry Taylor Artefacts Ltd trading as Atlantic 2000
Address PO Box 11, Ashton Under Lyne, OL7 7TR
Email: [email protected]
Declare under our own responsibility that the following product/s
Atlantic RX Digitale Range: 24kW
Atlantic ME Compacte Range: 36kW / 48kW / 60kW / 72kW
Atlantic ME Standard Range: 90 kW / 120 kW / 150kW / 180 kW / 210kW
245kW / 280kW 315kW / 350kW / 385kW / 420kW
455kW / 490kW / 525kW 560kW / 595kW / 630kW
665kW / 700kW / 735kW / 770kW / 805kW / 840kW
875kW / 910kW / 945kW / 980kW
are in compliance with European directives:
Directive 2009/125/CE (Eco-Design)
Directive 2010/30/UE (Energy Labelling)
Directive 2014/35/UE (Low Voltage)
Directive 2014/30/UE (Electromagnetic compatibility)
Directive 2014/68/UE (Pressure equipment directive)
are in compliance with European norm(s):
NF EN 60335 - 1 (Ranking index C 73800)
Name: Harry Howard MA CEng MCIBSE
Position: Director
Signature: ______________________________
Date: ______________________________
AB/TS 09/20
ATLANTIC 2000 - boilerplant sales ACM ATLANTIC - commissioning and maintenance ATLANTIC 4422 – spares
Registered in England. Company No: 1477687 Vat Reg No: 306 0653 89 Tel: [phone] Fax: [phone]
DECLARATION OF
CONFORMITY
11/11/20

ATLANTIC BOILERS, PO BOX 11, ASHTON UNDER LYNE, OL6 7TRT:0161 621 5960 E: [email protected]
FOR TECHNICAL HELP/ADVICE Call 0161 621 5960
or email [email protected]
FOR FULL PRODUCT RANGE & LITERATURE
Visit www.atlanticboilers.com