Atlantis LUXURY G16 User manual

G16 Luxury Collection
Twin Bowls Kitchen Sink
Owner’s Manual
Drop-in
Undermount

Tools Required:
– Ruler/Tape Measure – Pencil
– Masking Tape – Safety Glasses
– Kitchen Silicone Sealant – Screwdriver
– Drill – Jigsaw & Suitable Blade
(if work top cutout is required)
Option A
Sink – Drop-In Installation Instructions
1 – Locate the “drop-in” sink template inside the box. Carefully cut along the
outline and discard the inner section of the template. Place the paper template
onto the upper surface of your work top and position it carefully where you
want the sink to fit. When positioning the template take note of cabinet panels
and rails below as well as ensuring there will be enough access for faucet
connections. Fix the template in place with masking tape and carefully draw
around the inside of the template with a pencil. Remove the inner template.
OR
Invert sink and position onto the work top. Locate sink front to rear and right to
left so the bowl will not interfere with the cabinets below. Trace a pencil line around
the outside edge of the sink and remove the sink from the worktop. Measure in 7
mm from the initial sink outline and draw a second line inside the first.
2 – Drill starter hole inside of cutout line.
3 – Using a “Jigsaw”, cut inside of cutout line. Trial fit sink to check proper fit.
Cut Out Area
Masking Tape
Counter Top
Cut Out Area
Counter Top
Cut Out Area
Cut Inside of Line
Counter Top

4 – Install both strainers. Insert the metal strainer with the rubber seal into the
drain hole. Position the plastic bowl end the rubber gasket underneath the
drain hole. Using a screw, tighten the plastice bowl to the metal strainer.
1. Basket
2. Metal Strainer
3. Screw
4. Rubber seal
5. Rubber gasket
6. Main body
Note: plumbers putty is not required. If plumbers putty is used,
it replaces the rubber seal
5 – Verify that the sink fits perfectly. The lip of the sink should be resting
on the countertop.
6 – Insert clips in rails.
7 – Fix the clips.
8 – Seal the sink with silicone.
9 – Install faucet. Then make proper water and waste pipe connections.
1
2
4
5
6
3
Bottom View of Sink
Countertop
Screwdriver
Clip
Rail
Sink
Bottom View of Sink

Option B
Sink – Undermount Installation Instructions
1 – Locate the “undermount” template inside the box. Carefully cut along the
outline and discardthe inner section of the template. Place the paper template
onto the upper surface of your work top and positionit carefully where you want
the sink tofit. When positioning the template take note of cabinet panels and
rails below as well as ensuring there will be enough access for faucet connections.
Fix the template in place with masking tape and carefully draw around the
inside of the template with a pencil. Remove and discard the template.
2 – Drill starter hole inside of cutout line.
3 – Using a “Jigsaw”, cut inside of cutout line. Trial fit sink to check proper fit.
4 – Build a support frame.
Verify the fit of the sink and the counter top.
Cut Out Area
Masking Tape
Counter Top
Cut Out Area
Counter Top
Cut Out Area
Cut Inside of Line
Counter Top
770 mm
495 mm
Frame Frame
Rail Rail
Sink
Frontal view

5 – Install both strainers. Insert the metal strainer with the rubber seal into the
drain hole. Position the plastic bowl end the rubber gasket underneath the
drain hole. Using a screw, tighten the plastice bowl to the metal strainer.
1. Basket
2. Metal Strainer
3. Screw
4. Rubber seal
5. Rubber gasket
6. Main body
Note: plumbers putty is not required. If plumbers putty is used,
it replaces the rubber seal
6 – Insert sink on the support frame. Apply silicone sealant to each corner between
the frame and sink.
7 – Apply silicone sealant on the border of the sink and install the countertop.
Then remove exceeding sealant.
8 – Install faucet. Then make proper water and waste pipe connections.
1
2
4
5
6
3

CARE
Clean your sink regularly using warm soapy water. Always rinse the sink after using
any cleaning agent. The surface may be wiped with a cleansoft cloth to remove
water spotting. Do not cut, chop or dice food directly of the surface ofthe sink.
Do not let staining objects in direct contact with the sink for long period of time.
Do not use abrasive cleaners, scouring pads, or steel wool.
WARRANTY
Artika For Living Inc. is proud to offer you a one (1) year warranty. We warrant
it to be free of manufacturing defects in material and workmanship for a period of
one (1) year from the date of purchase. Should a defect arise within the Warranty
period, Artika For Living Inc. will provide a replacement free of charge.
Please call 866-661-9606 for details.
Our warranty does not cover a sink that has been installed incorrectly, or subjected
to abnormal use. Our Stainless Steel Sink is intended for residential use only, and
not commercial use. The Warranty does not cover shipping costs, labor costs or
any other cost associated with the installation or replacement of the sink, and is
extended to the original consumer.
Artika For Living Inc. is not liable for indirect or consequential damages arising
from improper use or installation of this sink.
QUE STIONS ? 1-866-661-9606
Atlantis Sink is a trademark of Artika
[email protected]