atomi smart AT2003 User manual

Sma WiFi Indoor Ceiling Fan
AT2003
Let’s get staed!
QuickSta Guide
v1.05/23

2 3
WHAT’S IN THE BOXFOR YOUR SAFETY
Standard
Mounting Bracket (x1)
Glass Shade (x1)12” Downrod (x1)
Bag A2
Bag B2
Blades Accessory Bag
Mounting Bracket Accessory
Blade
Screw (x7)
Clip (x1)Iron Washer
(x1)
Balance
Weight (x3)
Bag A1
Bag B1
Remote Control (x1)
Remote Control Bracket (x1)
Remote Control
Mount Screw (x2)
Remote Control
Mount Anchor (x2)
Remote Control Accessory Bag
Bag E1 Bag E2
Sticker (x2)
3M
Ceiling Fan (x1) Fan Blade (x3)
Know your ceiling height
Downrod Length
Ceiling Height
Flush mount /
Close mount
Less
than 2.74m
Up to 12in.
Downrod
2.74m
Up to 18in.
Downrod
3.04m
Up to 24in.
Downrod
3.35m
Up to 36in.
Downrod
3.65m
Up to 48in.
Downrod
3.96m
Up to 60in.
Downrod
4.26m
Up to 72in.
Downrod
4.57m
Mounting to high ceilings?
Maximize your comfo by choosing the right accessory downrod length foryour ceiling.
If you have an angled ceiling, you may need a longer downrod.
Visit www.atomisma.com to find additional downrod options.
Caution: Modifications not approved by the pay responsible for compliance could void user’s
authority to operate the equipment.
1. To reduce the riskof personal injury, do not bend the blade brackets when installing the brackets, balancing the
blades, or cleaning the fan. Do not inse foreign objects in between rotating fan blades.
2. To reduce the riskof fire, electric shock, or personal injury, mount directly to a structural framing member or to an
outlet box marked “acceptable for fan suppo of 31.8kg (70 lbs) or less”. For outlet box mounting, use mounting
screws provided with the outlet box.
3. The fan can be mounted to a structural framing member or an outlet box. When mounted to an outlet box, use
the screws provided with the outlet box.
4. The installation is in accordance with the National Electrical Code, ANSI/NFPA 70, and local codes.
5. To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning o the
circuit breaker to the outlet box and associated wall switch location.
6. To reduce the riskof electric shock, this fan must be installed with an isolating wall control/switch.
7. The wall switch used shall have been investigated and found acceptable for use as a general-use switch.
8. Aer making the wire connections, the wires should be spread apa with the grounded conductor and the
equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side
of the outlet box.
9. Aer the splices are made, they should be turned upward and pushed carefully up into the outlet box.
10. A grounded conductor is to be connected to a grounded conductor of power supply, a conductor of fan
identified as ungrounded conductor is to be connected to an ungrounded conductor of power supply, and a
conductor of fan identified for equipment grounding is to be connected to an equipment-grounding conductor.
11. To reduce the riskof electric shock, disconnect the electrical supplycircuit to the fan before installing the light kit.
12. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental
capabilities, or lackof experience and knowledge unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
13. Children should be supervised to ensure that they do not play with the appliance.
14. To avoid any accidental losses, all set screws must be checked and retightened, where necessary,
before installation.
15. Before installation, checkthat the outlet box is securely installed in place such that it is able to suppo at least
the fan weight.
READ AND SAVE ALL INSTRUCTIONS BEFORE USING.
WARNING
Light Ring (x1)
Bag D
Wire Nut (x3)
43in. Extension Wire
with Connector
(suitable for downrod
more than 18in.)
LED Board (x1) LED Board Cover (x1)
Light Fixture
This fixture comes pre-assembled. Please,
checkstep 2 on page 7 for instructions.
Receiver (x1)
Wood Screw (x2)
Washer (x2)

4 5
SELECT YOUR INSTALLATION LOCATION
Measure room dimensions
Flush Mounting Standard Mounting
Check the outlet box
30in.
from blade
tip to
nearest
wall or
obstruction
7. from boom edge
of blade to the floor
The fan must be secured to the building
structure or a fan-rated outlet box
capable of suppoing 31.8kg (70lbs).
CEILING FAN MOUNTING OPTIONS
Standard bracket maximum angle =
16 degrees
Unpack and inspect the fan carefully to confirm that all pas are included.
Pre-assembled. The Atomi Sma Ceiling Fan
comes already prepped for this installation option.
TOOLS NEEDED FOR INSTALLATION
Ladder Screwdriver Wire strippers Drill
(If applicable) (If mounting to a suppo structure or
concrete. Only concrete-compatible
screws are included.)
Ceiling Outlet Box Ceiling Outlet Box
12” Downrod
or longer
Other Mounting Options
If there isn’t an existing UL (cUL for Canadian Installation) listed mounting box, then read the
following instructions.
• Disconnect the power by removing fuses or turning o circuit breakers.
• Secure the outlet box directly to the building structure. Use appropriate fasteners and
building materials.
• The outlet box and its suppo must be able to fully suppo the moving weight of the fan
(31.8kg or 70 lbs). Do not use plastic outlet boxes.
Figures 1, 2 and 3 are examples of dierent ways to mount the outlet box.
ATTENTIONATTENTION
Depending on the location selected for
installation, you may need to purchase
and install a “Joist Hanger” for the
suppo of the outlet box. Make sure
the joist hanger you purchase has
been designed for use with ceiling
fans. (Fig. 4)
If you are installing the ceiling fan on a
sloped (vaulted) ceiling, you may need
a longer downrod to maintain proper
clearance between the tip of the
blade and the ceiling. A minimum
clearance of 12in. is suggested for
optimal operation.
If your outlet box is not mounted or if you do not have proper wiring in your outlet box, hire an electrician.
You will need a hot (black), neutral (white), and ground (green or bare copper) to operate this fan.
1 2
43
Outlet Box
Outlet Box
Outlet Box
Angled ceiling maximum 16° angle
Ceiling Mounting Plate
Recessed
Outlet Box

6 7
INSTALLING THE BLADES
1
One at a time, inse each blade into the slot on the fan structure.
Secure each blade with the screws and washers found in Bag A1.
FOR THIS STEP YOU WILL NEED FOR THIS STEP YOU WILL NEED
ASSEMBLING THE LIGHT FIXTURE
2
A1
BAG
1
2
Remove the four screws from the fan.
Aach the light ring to the fan by
tightening the four screws securely.
Make sure to pass the white connector wire
through the center hole of the light ring.
ATTENTION: Screws must be
tightened securely before
fan is operated.
Do not make blades load-
bearing when installing the
light ring and LED board.
Using a screwdriver detach the three pas that come together:
the light ring, the LED board, and the LED board cover.
Note: Save these screws to be used in step 4.
WARNING
WARNING

8 9
3
3
4
Pass the white connector through the center hole
of the LED Board. Connect the white plug from the
housing structure to the white plug from the LED board.
Aach the LED board cover using the three
screws removed (explained in step 1).
Do not press the LEDs on
the LED board hardly when
connecting the plug.
Check that LEDs are not crimped by the
LED board cover aer installed. Do not
make blades loading-bearing when
installate light ring and LED board.
WARNING
WARNING
INSTALLING THE BRACKETS
Only use the provided Atomi Sma ceiling bracket that comes with your fan.
Remove any existing brackets from your ceiling prior to installation.
Secure the bracket to a ceiling box that is acceptable for fan suppo of 32kg (70lbs).
You have two options for installation. Pickwhich one works best for your location.
PREVENT POSSIBLE ELECTRIC SHOCK. Before installing your
fan, disconnect the power by turning o the circuit breakers
to the outlet box associated with the wall switch location.
WARNING
Standard Bracket
B1
Up to 16°
Standard bracket maximum angle =
16 degrees
OPTION 1
Use machine screws (provided with your
outlet box) and washers when securing
to existing ceiling fan-rated outlet box.
OPTION 2
Use wood screws and washers (included in
Bag B2) when securing to suppo structure
with approved electrical outlet box.
Drill 9/64” pilot holes in suppo structure
to aid in securing the ceiling bracket.
BAG

10 11
Locate and remove the clip and pin.
Loosen the screws and remove the downrod, canopy, and funnel.
REPLACING THE DOWNROD (OPTIONAL)
4
This step is for Standard and Angled Mounting only.
For the Flush Mounting (pre-assembled) please go to Step 5.
If you have a longer downrod from Atomi Sma, please, follow the same instructions.
3
4
FOR THIS STEP YOU WILL NEED
12in. DOWNROD
2
3
1
Standard or Angled Mounting
1
Detach the red and blue wires from the wire
splier. Unplug the red and blue wires.
Li the canopy and funnel.
2
PREVENT FAN FALLING INJURY OR DEATH:
• ALWAYS tighten screws with a screwdriver or a drill.
• DO NOT hand-tighten screws.
• CHECK that the screws are tight using
screwdrivers each time you change fan direction.
WARNING

12 13
9
10
Tighten the screws.
Re-aach the wires to the wire splier, matching the colors. Plug the red and blue wires.
Slide down the funnel.
7
8
Remove the clip and pin from the new downrod.
Inse the canopy and funnel
into the downrod, passing all
wires through the downrod.
5
6
2
3
1
2
1
Hold the canopy and funnel up to
inse the pin and clip back in place.

14 15
IMPORTANT INFORMATION.
Turn the wires upward and push them carefully back through the hanger
bracket into the outlet box. Spread the wires apa, with the grounded wires on
one side of the outlet box and the ungrounded wires on the other side of the
outlet box. Make sure the wires are still atached to the wire nuts. Aer splicing
the wires, turn them upward and push them carefully into the outlet box.
HANGING THE FAN
5
Li and carefully hang the fan on the mounting bracket.
WIRING THE FAN
6
Carefully follow these steps to get your fan wired safely and quickly.
If you are unfamiliar with wiring or uncomfoable doing it yourself, please contact a qualified electrician.
1
Slide the remote receiver between the mounting bracket and the top of the downrod.
FOR THIS STEP YOU WILL NEED
D
BAG
THE CEILING FAN MUST BE GROUNDED.
If the ground wire for the installation site
is not present oryou’re unsure what this
means, immediately STOP installation
and consult a qualified electrician.
WIRING MUST BE UP TO CODE. All wiring
must be in accordance with national and
local electrical codes. If you are unfamiliar
with wiring or in doubt, consult a
qualified electrician.
Note: Make sure the downrod is locked and secured to the groove inside the mounting bracket.
Be sure that the wires
are not pressed by
the fan.
WARNING
WARNING WARNING

16 17
2
1
3
2
INSTALLING THE CANOPY
7
2
1
Li the canopy into place so that the screw
holes are aligned with the housing holes.
Inse the screws and loosely secure them.
Fit the canopy in place as shown (1) and
turn it counter-clockwise.
Tighten the screws.
Push the bare metal ends of the wires together and slide a wire nut over them.
Twist the wire nut clockwise until tight.
Give it a gentle pull to ensure none of the wires come apa.
FOR THIS STEP YOU WILL NEED
2.1
Connect the BLACK
(ungrounded Z) wire from
the RECEIVER to the BLACK
wire from the CEILING.
2.3
Connect the GREEN
(grounded G) wire from the
FAN to the GREEN OR BARE
wire from the CEILING.
2.2
Connect the WHITE (W)
wire from the RECEIVER
to the WHITE wire from
the CEILING.

18
INSTALLING THE GLASS SHADE
8
12
Li the glass shade and align the notches in the
glass shade with the tabs in the light ring.
Aach the glass shade by liing and turning it
clockwise one-third of a full turn until it stops.
NOTE: Check to ensure proper engagement.
PREVENT GLASS FALLING.
Make sure that glass shade
is properly secured.
Now that your Sma WiFi Ceiling
Fan is installed, it is time to
connect and sta using it.
Connecting your
Sma WiFi
Ceiling Fan
Get the app
Download the Atomi Sma app
from the App Store or Google Play.
Register
Follow the on-screen instructions
and register an account.
1 2
Make sure to allow access to Location (Android),
Bluetooth®and Local Network (iOS).
19
Register
3
Turn on the circuit breakers to the outlet box associated with the wall switch
location, then turn on the wall switch and checkif the Atomi Sma WiFi
Ceiling Fan has 100% of white light brightness. You can checkthe brightness
using the Atomi Sma app or with the included remote controller.
If it does not have 100% of white light brightness,
please check all wiring for anywrong connections.
If it has 100% of white light brightness, please proceed to the next step.
Having issues aaching the glass shade?
Make sure the light ring was installed in the
correct position (See page 7).
Scan the QR code below
or go to hps://atomisma.com/app/
WARNING

20 21
USING THE REMOTE CONTROL
Control buons
Note: Requires 2 AAA baeries (not included).
FOR THIS STEP YOU WILL NEED
E1
BAG
3 4
5
Add Device
WiFi
Password
Continue
Turn on your sma device
And long press (5 seconds) the WiFi buon on the
remote. The fan light will sta flashing white.
If the pop-up does not appear, close the
app and try again. Still nothing? Read the
“Troubleshooting” section on this user guide.
Connect your 2.4GHz
WiFi network*
Enter or select your local WiFi name,
enter your password, then press “Continue”.
*Make sure you’re connected to a 2.4GHz WiFi network
(Atomi Sma can’t connect to 5GHz networks).
WiFi pairing: Long press (more
than 5 seconds) to connect
fan to network
Sho press to recover WiFi
connection
Fan reversal: Long press
(more than 5 seconds) to pair
remote and the fan
Long press to turn ON/OFF
notification sound
Fan Timer
Light Timer
Light ON/OFF
Cool White
Change Light to Green
Change Light to Blue
RGB +
Fan ON/OFF
Long press (10 seconds)
to turn WiFi OFF
Fan Speed (from 1 to 6)
Brightness +
Warm White
Brightness-
Change Light to Red
RGB-
Add your sma device
Press “Add Device” or the “+” sign and select
“Connect Device” on the pop-up that appears.

22 23
1
1
2 3
32
Remove the screws from
your light switch cover
(Do not remove the cover).
Place the remote control mount
over the cover and aach it with
the cover’s screws.
Slide the remote control
holder in place, then inse
the controller.
Slide the remote control
holder in place, then inse
the controller.
Use a screwdriver to
screw in the anchors
and screws in each hole.
Aaching to an existing light switch
Note: This is only compatible with toggle switches.
Mounting it to the wall
E2
BAG
Use a pencil to mark the holes
on the wall and checkfor
alignment, then drill the holes.
Alternatively, you can use the 3M sticker to fix the bracket on the wall.
USING THE BALANCE KIT
Follow these steps to properly even out the blade weight distribution.
1
3
2
4
Ensure your fan is correctly installed and all
fasteners are secure. It is recommended to
run the fan on HIGH for 10-20 seconds to
peorm these next steps.
Now, move the clip to the blade that
caused the least wobble. Run your fan
and observe the wobble. Adjust the clip
in small increments along the edge of
the blade to achieve the least wobble.
Pause your fan to aach the clip to the end of
any blade. Run your fan and observe the wobble.
Stop the fan and move the clip to the next blade,
repeating these steps for all the fan blades.
At the location where you noticed
the least wobble, adhere the
balance weight and remove the clip.
FOR THIS STEP YOU WILL NEED
A2
BAG
Product is ready to use.

24 25
TROUBLESHOOTING
The pop-up does not appear when
adding a device.
Make sure that you are allowing the app to
access your phone’s Location (Android), Bluetooth
and Local Network (iOS). For more details, visit our
website’s Suppo page.
If the pop-up still doesn’t appear, follow the steps
below:
1. Press “Add Device” or the “+” sign and select
your Atomi Sma device.
2. Follow the on-screen instructions (Make sure
you connect to a 2.4GHz WiFi Network).
My WiFi network doesn’t appear in the
Atomi Sma app.
Use your smaphone to confirm that you have
at least two WiFi bars in the vicinity of your Atomi
Sma device. If not, move your Atomi Sma device
closer to your router. (The list will refresh every10
seconds).
Cannot connect to my WiFi network.
Make sure thatyou have entered the correct WiFi
password during the WiFi setup. Check if there are
problems with your internet connection. If the WiFi
signal is too weak, reset your WiFi router and try
again.
I’m geing “Failed to Add Device”,
“Failed to find router” or “DHCP” error.
- Confirm that your phone is connected to a
2.4GHz WiFi network.
- Checkwhether the router password you
entered is correct.
- Confirm that the DHCP service is enabled on
your router seings.
- Make sure that your WiFi signal is strong.
- Temporarily disable your 5GHz network.
- If you have a mesh network/router that does
not allow you to disable 5GHz, try to move
faher away from your router until your phone
moves to the 2.4GHz band.
- For more Connection Troubleshooting tips, visit
atomisma.com/connection-troubleshooting/
My Atomi Sma device appears as
“Unavailable” or “Oine” in the app.
Refresh the device list.
I just replaced my router.
If you replace your router, you will need to reset
your devices and add them again to the app.
How to reset my device?
Long press (5 seconds) the WiFi buon on the
remote control.
The Ceiling Fan does not work.
- Make sure that the circuit breaker power is
turned on.
- Confirm that your wall switch is on.
- Turn o the power from your circuit breaker
and check the fan’s wiring for any connection
issues.
The Ceiling Fan is too noisy.
Confirm that the blades are properly installed.
The Ceiling Fan is wobbling.
- Confirm that the downrod was correctly
aached to the mounting bracket.
- Make sure that the mounting screws are firmly
screwed in.
- Confirm that the canopy is firmly aached to
the mounting bracket.
- Note any warped blades. If even one blade is
slightly distoed, it can create an imbalance.
Checkfor warping by standing on a secure
ladder and looking down the edge of the blade
toward the motor. If there’s any curvature, the
blade is considered warped. Repeat this step
for every blade. If they do not appear uneven,
confirm that the screws that aach the blades
are tightened and secure. Warped blades
cannot be balanced.
Use the included balance kit to even out the
blade weight distribution. Directions on how to
use it can be found on page 23.
For more information about app and device features, tutorials and troubleshooting tips go to:
www.atomisma.com/helpCeilingFan
STILL CAN’T CONNECT?
NEED ASSISTANCE?
Our friendly customer service team will work hard to put a
smile backon your face. Here’s how we can connect.
1-800-757-1440
Mon-Fri 9:00-5:00 EST (U.S.)
or suppo@atomiusa.com
How to access the baery
compament?
- Remove the remote control baery
compament cover located on the back of the
remote.
- Inse 2x AAA baeries (not included) into the
compament, making sure they are installed
correctly (+) and (-).
- Aach the cover back into place.
- Test the remote control to see if it works by
pressing any buon. The remote control
indicator light should turn on when a buon is
pressed.
How to use baeries for the remote
control?
- Always purchase the correct size and grade of
the baery most suitable for the intended use.
- Replace all baeries of a set at the same time.
- Clean the baeries’ contacts and also those of
the device prior to baery installation.
- Ensure the baeries are installed correctlywith
regard of polarity (+ and-).
- Remove baeries from equipment that is not to
be used for an extended period of time.
- Remove used baeries promptly.
Remote Control doesn’t work.
- Make sure that the remote was paired to the fan.
Please see page 21 for more details.
- Make sure that the 2x AAA baeries (not
included) are correctly in place.
- Replace the baeries with new ones.
How to pair the remote control?
1. Once connected to the app, turn o the wall
switch and wait 30 seconds.
2. Turn on the wall switch, point the remote control
to the ceiling fan, and press &hold the fan
switch buon for 4 seconds. Once you hear a
beep, pairing is complete.
NOTE: Please complete this step within 30
seconds from the moment the wall switch is
turned on. Otherwise, repeat steps 1 and 2.
3. If you have more than one fan, to avoid
inteerence between fans during the remote
pairing process, make sure that only1 fan is
powered on at a time. If you did not hear a
beep on step 2, please repeat steps 1 and 2.

26 27
FCC Notice:
This device complies with Pa 15 of the FCC Rules. Operation is subject to the two following conditions:
1. This device may not cause harmful inteerence.
2. This device must accept any inteerence received, including inteerence that may cause undesired
operation.
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to pa 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
inteerence in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful inteerence
to radio communications. However, there is no guarantee that inteerence will not occur in a paicular
installation. If this equipment does cause harmful inteerence to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the
inteerence by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution:
Modifications not approved by the pay responsible for compliance could void user’s authority to operate
the equipment.
WELCOME TOTHE ATOMI SMART FAMILY!
We know you will love our products so much that we are
giving you an exclusive 15% o your next purchase on
atomisma.com.
Terms and conditions apply.
1. Coupon is onlyvalid on the Atomi Sma website
www.atomisma.com.
2. A valid code must be entered at the checkout page in
order to redeem the promotion.
3. Customers can only redeem one time at checkout.
4. Customers can only use the promo code once.
5. Atomi Sma reserves the right to cancel or modify any
order, or revoke the use of the promo code for any reason.
6. Unless otherwise stated, promo codes are not valid in
conjunction with other promotions or discounts.
7. Additional terms and conditions may be specified in
relation to specific promo code (for example, duration,
eligibility, discount amount and products covered), and
will govern the use and redemption of those vouchers.
8. Promo code is not exchangeable for cash.
9. Atomi Sma will not be liable and/or be required to oer
replacement codes, discounts, credits, cash or otherwise
compensate customers for:
a. discontinued or cancelled promo code;
b. improper use of, or inability to redeem, a promo code; or
c. the inability to redeem promo code due to technical
issues.
The following terms and conditions apply to the promo code:
For questions or concerns, email us at suppo@atomiusa.com
Manufactured and marketed by Atomi Inc.
10 West 33rd St., New York, NY 10001
atomi™ is a trademark of Atomi Inc.
atomi sma®is a registered trademarkof Atomi Inc.
Designed by Atomi in New York. Made in China
10-year limited warranty from the date of purchase against defects in material and workmanship.
Log onto hps://atomisma.com/shop-now/
Add to Ca
Enter promo code ATOMI15OFF
Proceed to checkout
Free shipping on orders over $50
*within the contiguous U.S. only*