atomi smart AT2124 User manual

Sma WiFi Outdoor Ceiling Fan
AT2124
Let’s get staed!
QuickSta Guide
v1.05/23

2 3
WHAT’S IN THE BOXFOR YOUR SAFETY
Light Ring (x1)Acrylic Shade (x1)
12” Downrod (x1)
Bag D
Wire Nut (x3)
Bag A2
Blades Accessory Bag
Blade
Screw (x20)
Clip (x1) Balance
Weight (x6)
Bag A1
Remote Control (x1)
Remote Control Bracket (x1)
Remote Control
Mount Screw (x2)
Remote Control
Mount Anchor (x2)
Remote Control Accessory Bag
Bag E1 Bag E2
Sticker (x2)
3M
Fan Blade (x6)Ceiling Fan (x1)
LED Board (x1)
READ AND SAVE ALL INSTRUCTIONS BEFORE USING.
WARNING
Mounting to high ceilings?
Maximize your comfo by choosing the right accessory downrod length for your ceiling.
If you have an angled ceiling, you may need a longer downrod.
Visit www.atomisma.com to find additional downrod options.
Caution: Modifications not approved by the pay responsible for compliance could void user’s
authority to operate the equipment.
1. To reduce the riskof personal injury, do not bend the blade brackets when installing the brackets, balancing the
blades, or cleaning the fan. Do not inse foreign objects in between rotating fan blades.
2. To reduce the riskof fire, electric shock, or personal injury, mount directly to a structural framing member or to an
outlet box marked “acceptable for fan suppo of 31.8kg (70 lbs) or less”. For outlet box mounting, use mounting
screws provided with the outlet box.
3. The fan can be mounted to a structural framing member or an outlet box. When mounted to an outlet box, use
the screws provided with the outlet box.
4. The installation is in accordance with the National Electrical Code, ANSI/NFPA 70, and local codes.
5. To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning o the
circuit breaker to the outlet box and associated wall switch location.
6. To reduce the riskof electric shock, this fan must be installed with an isolating wall control/switch.
7. The wall switch used shall have been investigated and found acceptable for use as a general-use switch.
8. Aer making the wire connections, the wires should be spread apa with the grounded conductor and the
equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side
of the outlet box.
9. Aer the splices are made, theyshould be turned upward and pushed carefully up into the outlet box.
10. A grounded conductor is to be connected to a grounded conductor of power supply, a conductor of fan
identified as ungrounded conductor is to be connected to an ungrounded conductor of power supply, and a
conductor of fan identified for equipment grounding is to be connected to an equipment-grounding conductor.
11. To reduce the riskof electric shock, disconnect the electrical supply circuit to the fan before installing the light kit.
12. This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental
capabilities, or lackof experience and knowledge unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
13. Children should be supervised to ensure that they do not playwith the appliance.
14. To avoid any accidental losses, all set screws must be checked and retightened, where necessary,
before installation.
15. Before installation, checkthat the outlet box is securely installed in place such that it is able to suppo at least
the fan weight.
These pas come
pre-assembled.
Please, check
step 2 on page 7
for instructions.
Know your ceiling height
Downrod Length
Ceiling Height
Flush mount /
Close mount
Less
than 2.74m
Up to 12in.
Downrod
2.74m
Up to 18in.
Downrod
Up to 24in.
Downrod
3.35m
Up to 36in.
Downrod
3.65m
Up to 48in.
Downrod
3.96m
Up to 60in.
Downrod
4.26m
Up to 72in.
Downrod
4.57m3.0m
Standard
Mounting Bracket (x1)
Bag B2
Mounting Bracket Accessory
Bag B1
Wood Screw (x2)
Washer (x2)

4 5
SELECT YOUR INSTALLATION LOCATION
Measure room dimensions
Flush Mounting Standard Mounting
Check the outlet box
30in.
from blade
tip to
nearest
wall or
obstruction 7. from boom edge
of blade to the floor The fan must be secured to a fan-rated outlet
box capable of suppoing 31.8kg (70lbs).
CEILING FAN MOUNTING OPTIONS
Standard bracket maximum angle =
20 degrees
Unpack and inspect the fan carefully to confirm that all pas are included.
Pre-assembled. The Atomi Sma Ceiling Fan
comes already prepped for this installation option.
TOOLS NEEDED FOR INSTALLATION
Ladder Screwdriver Wire strippers Drill
(If applicable) (If mounting to a suppo structure or
concrete. Only concrete-compatible
screws are included.)
Ceiling Outlet Box Ceiling Outlet Box
12” Downrod
or longer
Other Mounting Options
If there isn’t an existing UL (cUL for Canadian Installation) listed mounting box, then read the
following instructions.
• Disconnect the power by removing fuses or turning o circuit breakers.
• Secure the outlet box directly to the building structure. Use appropriate fasteners and
building materials.
• The outlet box and its suppo must be able to fully suppo the moving weight of the fan
(31.8kg or 70 lbs). Do not use plastic outlet boxes.
Figures 1, 2 and 3 are examples of dierent ways to mount the outlet box.
ATTENTIONATTENTION
Depending on the location selected for
installation, you may need to purchase
and install a “Joist Hanger” for the
suppo of the outlet box. Make sure
the joist hanger you purchase has
been designed for use with ceiling
fans. (Fig. 4)
If you are installing the ceiling fan on a
sloped (vaulted) ceiling, you may need
a longer downrod to maintain proper
clearance between the tip of the
blade and the ceiling. A minimum
clearance of 12in. is suggested for
optimal operation.
If your outlet box is not mounted or if you do not have proper wiring in your outlet box, hire an electrician.
You will need a hot (black), neutral (white), and ground (green or bare copper) to operate this fan.
1 2
43
Outlet Box
Outlet Box
Outlet Box
Angled ceiling maximum 20° angle
Ceiling Mounting Plate
Recessed
Outlet Box

6 7
INSTALLING THE BLADES
1
One at a time, inse each blade into the slot on the fan structure.
Secure each blade with the screws found in Bag A1.
FOR THIS STEP YOU WILL NEED FOR THIS STEP YOU WILL NEED
ASSEMBLING THE LIGHT FIXTURE
2
A1
BAG
1
2
Detach the LED board from the light ring using a screwdriver.
Note: Save these screws to be used in step 4.
Remove the four screws from the fan.
Aach the light ring to the fan by
tightening the four screws securely.
Make sure to pass the white connector wire
through the center hole of the light ring.
WARNING
ATTENTION: Screws must be
tightened securely before
fan is operated.
Do not make blades load-
bearing when installing the
light ring and LED board.
WARNING

8 9
3
4
Connect the white plug from the housing structure to the white plug from the LED board.
Aach the LED board cover using the four
screws removed (explained in step 1).
3
INSTALLING THE STANDARD BRACKET
PREVENT POSSIBLE ELECTRIC SHOCK. Before installing your
fan, disconnect the power by turning o the circuit breakers
to the outlet box associated with the wall switch location.
WARNING
Up to 20°
Standard bracket maximum angle =
20 degrees
Option 1:
Machine Screws
Use machine screws (provided with your
outlet box) and washers when securing to
existing ceiling fan-rated outlet box.
Option 2:
Wood Screws
Use wood screws and washers (included in
Bag B2) when securing to suppo structure
with approved electrical outlet box.
Drill 9/64” pilot holes in suppo structure
to aid in securing the ceiling bracket.
B1
BAG
Only use the provided Atomi Sma ceiling bracket that comes with your fan.
Remove any existing brackets from your ceiling prior to installation.
Secure the bracket to a ceiling box that is acceptable for fan suppo of 31.8kg (70lbs).
There are two options for the bracket installation so please choose which option works best
foryour location. Use option 1 for standard ceiling installation using a fan-rated outlet box.
FOR THIS STEP YOU WILL NEED

10 11
Standard or Angled Mounting
1
Locate and remove the clip and pin.
Li the canopy and funnel.
Loosen the screws and remove the downrod, canopy, and funnel.
REPLACING THE DOWNROD (OPTIONAL)
4
This step is for Standard and Angled Mounting only.
For the Flush Mounting (pre-assembled) please go to Step 5.
If you have a longer downrod from Atomi Sma, please, follow the same instructions.
2
3
FOR THIS STEP YOU WILL NEED
PREVENT FAN FALLING INJURY OR DEATH:
• ALWAYS tighten screws with a screwdriver or a drill.
• DO NOT hand-tighten screws.
• CHECK that the screws are tight using
screwdrivers each time you change fan direction.
2
3
1
12in. DOWNROD
WARNING

12 13
8
Tighten the screws.
Slide down the funnel.
6
7
Remove the clip and pin from the new downrod.
Inse the canopy and funnel into the downrod,
passing all wires through the downrod.
Hold the canopy and funnel up to
inse the pin and clip back in place.
4
5
2
3
1
2
1

14 15
HANGING THE FAN
5
Li and carefully hang the fan on the mounting bracket.
WIRING THE FAN
6
Carefully follow these steps to get your fan wired safely and quickly.
If you are unfamiliar with wiring or uncomfoable doing it yourself, please contact a qualified electrician.
FOR THIS STEP YOU WILL NEED
D
BAG
THE CEILING FAN MUST BE GROUNDED.
If the ground wire for the installation site
is not present oryou’re unsure what this
means, immediately STOP installation
and consult a qualified electrician.
WIRING MUST BE UP TO CODE. All wiring
must be in accordance with national and
local electrical codes. If you are unfamiliar
with wiring or in doubt, consult a
qualified electrician.
Note: Make sure the downrod is locked and secured to the groove inside the mounting bracket.
Be sure that the wires
are not pressed by
the fan.
1
3
2
1
Connect the BLACK
(ungrounded Z) wire from
the RECEIVER to the BLACK
wire from the CEILING.
3
Connect the GREEN
(grounded G) wire from the
FAN to the GREEN OR BARE
wire from the CEILING.
2
Connect the WHITE (W)
wire from the RECEIVER
to the WHITE wire from
the CEILING.
Push the bare metal ends of the
wires together and slide a wire
nut over them. Twist the wire nut
clockwise until tight.
Give it a gentle pull to ensure
none of the wires come apa. WG
Z
WARNING
WARNING WARNING
Ground Wire
Ground Wire

16 17
INSTALLING THE CANOPY
72
1
Li the canopy into place so that the screw
holes are aligned with the housing holes.
Inse the screws and loosely secure them.
Fit the canopy in place as shown and
turn it counter-clockwise.
Tighten the screws.
FOR THIS STEP YOU WILL NEED
3
Li the cover plate and turn it clockwise to aach it to the canopy.

18
INSTALLING THE ACRYLIC SHADE
8
12
3
Li the acrylic shade and align the notches in the
acrylic shade with the tabs in the light ring.
Aach the acrylic shade by liing and turning it
clockwise one-third of a full turn until it stops.
NOTE: Check to ensure proper engagement.
Turn on the circuit breakers to the outlet box associated with the wall switch
location, then turn on the wall switch and checkif the Atomi Sma WiFi
Ceiling Fan has100% of white light brightness. You can checkthe brightness
using the Atomi Sma app or with the included remote controller.
If it does not have 100% of white light brightness,
please check all wiring for anywrong connections.
If it has 100% of white light brightness, please proceed to the next step.
PREVENT ACRYLIC FALLING.
Make sure that acrylic
shade is properly secured.
Now that your Sma WiFi Ceiling
Fan is installed, it is time to
connect and sta using it.
Connecting your
Sma WiFi
Ceiling Fan
1 2
19
Having issues aaching the acrylic shade?
Make sure the light ring was installed in the
correct position (See page 7).
Get the app
Download the Atomi Sma app
from the App Store or Google Play.
Register
Follow the on-screen instructions
and register an account.
Make sure to allow access to Location (Android),
Bluetooth®and Local Network (iOS).
Register
Scan the QR code below
or go to hps://atomisma.com/app/
WARNING