ATOMI AT1372 User manual

Need assistance?
LED Vanity Mirror + Speaker
Call 1-800-757-1440
Mon-Fri 9:00 a.m. - 5:00 p.m. EST (US)
or email us at [e-mail]
Date Code: 08/19
User Manual
WE
CAN
HELP
DO NOT RETURN THIS
PRODUCT TO THE STORE

IMPORTANT SAFEGUARDS
When used in the directed manner, this unit has been designed
and manufactured to ensure your personal safety. However,
improper use can result in potential electrical shockor fire hazards.
READ ALL INSTRUCTIONS BEFORE USING.
GENERAL
1. Water and Moisture– The unit should not be used near water.
For example: near a bathtub, washbowl, kitchen sink, laundry tub,
swimming pool or in a wet basement.
2. Ventilation – The unit should be situated so that its location or
position does not inteere with its proper ventilation. For
example, it should not be situated on a bed, sofa, rug or similar
suace that may blockventilation openings. Also, it should not
be placed in a built-in installation, such as a bookcase or
cabinet, which may impede the flow of air through the ventilation
openings.
3. Heat– The unit should be situated away from heat sources such
as radiators, heat registers, stoves or other appliances (including
amplifiers) that produce heat. Never place the mirror in or expose
the mirror to direct sunlight. Le unaended, the sun’s rays can
reflect to become focused and cause excessive heat and/or fire.
4. Power Sources– The unit should be connected to a power supply
only of the type described in the operating instructions or as
marked on the appliance.
5. Power-Cable Protection – Power supplycables should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them. It is always best to have a clear
area from where the cable exits the unit to where it is plugged
into an AC socket.
6. Cleaning– The unit should be cleaned only with damp cloth.
7. Objects and Liquid Entry– Care should be taken so that objects
do not fall and liquids are not spilled into any openings or vents
located on the product.
8. Lightning and Power Surge Protection– Unplug the unit from the
wall socket during a lightning storm or when it is le unaended
and unused for long periods of time.This will prevent damage to
the product due to lightning and power-line surges.
9. Overloading– Do not overload wall sockets, extension cords, or
integral convenience receptacles as this can result in a riskof fire
or electric shock.
10.Periods of Non-use– If the unit is to be le unused for an
extended period of time, such as a month or longer, the power
cable should be unplugged from the unit to prevent damage or
corrosion.
SAVE THESE INSTRUCTIONS
Please exercise caution when in use as the mirror
is made of glass.
1 2

3 4
Thankyou for purchasing the
atomi LED Vanity Mirror + Speaker
The atomi LED Vanity Mirror + Speaker doubles as a
vanity mirror and Bluetooth™ speaker. Equipped with
natural daylight LED lighting that flawlessly magnifies
your beauty while it streams your geing ready playlist.
What’s Inside
Meet the atomi LED
Vanity Mirror + Speaker
LED Vanity Mirror
+ Speaker
User
Manual
Power
Supply
Speaker
High-quality
speaker for
wireless streaming
LED Lighting
Bright LED
lighting with
high/low modes
Double-Sided Mirror
1x/7x Magnification
7 inch double-sided mirror
for a flawless reflection
LED Indicator
Indicates power
status and
Bluetooth™ pairing
Bluetooth™ Speaker Specs
Speaker: 5 wa hi-fi driver with passive subwoofer
Bluetooth™: Bluetooth™ 4.1 - 33 . Range
Charge Station Specs
Power Supply
Input:100-240V~50/60Hz 0.65A Max Output: 9V 2.5A
LED Vanity Mirror+Speaker
DC Input: 9V 2.5A USB Output: 5V 1A
Baery: 3.7V 4000mAh
USB
Po
AUX
Power
input

5 6
NOTE:
1. Bluetooth™ speaker will automatically power o aer 10 minutes of
inactivity.
2. When the baery’s voltage is less than 3.1V, the Bluetooth™ speaker
will automatically power o.
3. When LED Vanity Mirror + Speaker is plugged into power source, the
speaker will automatically use DC power.
Controls LED Indicator
1. Power: When the baery is low, the LED indicator will
flash red rapidly. When LEDVanity Mirror + Speaker is
plugged in, the LED indicator will slowly flash red.
When the baery is full, the LED indicator will turn
green and will automatically turn o aer 10 minutes.
2. Bluetooth™: LED indicator flashes blue rapidly when
speaker is in pairing mode. When speaker is
successfully paired, LED indicator will turn blue. When
speaker is in use, LED indicator will slowly flash blue.
1 2
Power ON/OFF: Press and hold for 3 seconds to turn
ON/OFF Bluetooth™ speaker. When speaker
is on, press to switch between AUX / Bluetooth™.
Volume Up: Press to increase speaker volume.
Next: Press to switch to next song.
Play/Pause: Press to play/pause song or to
answer or end call when ringtone is played.
Long press (5 seconds) to reject incoming call.
Previous: Press to switch to last song.
Volume Down: Press to decrease speaker volume.
LED Light: Press and hold for 3 seconds to turn ON the
light. Press again to switch light intensity (3 modes).
Press and hold for 3 seconds to turn OFF the light.

7 8
2. Once turned on, LEDVanity Mirror + Speaker should
appear on your device’s Bluetooth™ list. If a message
such as “Not Paired” or “Not Connected” appears,
select "atomi Vanity Mirror Speaker" to connect.
3. Once pairing is successful, you will see a solid
(non-flashing) blue light.
Bluetooth™ Setup
Bluetooth
Seings
Bluetooth
My Car
atomi Vanity Mirror Speaker
MY DEVICES
OTHER DEVICES
2.
3.
1.
Any Bluetooth™-enabled device (4.1) can be paired with
LED Vanity Mirror + Speaker.
1. Press and hold the power buon for 3 seconds to turn
speaker on. When LED Vanity Mirror + Speaker is turned on,
a flashing blue light will pulse above the buons. The
speaker will then enter into auto-pairing mode and aempt
to pair with a nearby Bluetooth™ device.

910
You can connect a smaphone, tablet, computer or other
type of mobile device to the speaker using a 3.5 mm audio
cable (not provided).
Using a 3.5 mm audio cable, connectyour audio device to
the AUX connector on the LED Vanity Mirror + Speaker.
Press the power buon to turn speaker on.
4. You may now play music on LED Vanity Mirror + Speaker
through your device. The next time the speaker is
powered on, it will automatically link with the last paired
Bluetooth™ device. To pair with a new device, follow
steps 1-3.
NOTE: A Bluetooth™ device must be within 33 feet LED Vanity Mirror +
Speaker to be paired with it.
Connect an Audio Cable
4.

11 12
Press and hold for 3 seconds to turn ON the light.
Press again to switch light intensity (3 modes).
Press and hold for 3 seconds to turn OFF the light.
When LED light turns red, the LED Vanity Mirror + Speaker
has 10% baery le and should be connected to the AC adapter.
When charging by USB, the mirror must be connected to the
power cord to enable USB charging.
Light Control Charging your LED
Vanity Mirror + Speaker

13 14
FCC Information
This equipment complies with FCC RF radiation exposure
limits set foh for an uncontrolled environment.
Operation is subject to the following two conditions:
(1) This device may not cause inteerence and (2) This
device must accept any inteerence received, including
inteerence that may cause undesired operation
Warning: Changes or modifications to this unit not expressly approved by
the pay responsible for compliance could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to complywith the limits for a
Class B digital device, pursuant to Pa 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful inteerence in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
inteerence to radio communications.
However, there is no guarantee that inteerence will not
occur in a paicular installation. If this equipment does
cause harmful inteerence to radio or television reception,
which can be determined by turning the equipment o and
on, the user is encouraged to try to correct the inteerence
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
For questions or concerns, email us at [e-mail]
Manufactured and marketed byAtomi Inc.
10 West 33rd St., New York, NY 10001
atomi™ is a trademarkof Atomi Inc.
Designed by atomi in New York. Made in China
One-year limited warranty from the date of purchase
against defects in material and workmanship.