Audio Technica GENUINE ACCESSORIES AT8662 User manual

AT8662
MICROPHONE SHOCK MOUNT (for Unipoint Series Gooseneck Microphones)
INSTALLATION
1. Locate the center of the mounting location and mark it. Allow
enough clearance to accommodate the shock mount’s ange
on the desired surface and make certain there are no physical
obstructions below the desired location.
2. Using a 51.0mm hole saw, drill the large through-hole for the
shock mount.
3. Set the shock mount into the hole and mark the location of the
three mounting screw holes. Make certain to “center” the mount
in the large hole before marking the three small mounting
screw locations.
4. Using a 1.5mm drill bit, drill three pilot holes for the mounting
screws.
5. After installing the microphone, assure maximum shock mount
effectiveness by providing some slack in the connecting cable.
FORM No. ATGC-L0314-13-E
Machida • Tokyo • Japan
COMPATIBLE MICROPHONES
UniPoint® Series AT859QMLa
U857Q U857QU
U857QM U857QMU
U857QL U857QLU
U857QSU
U859QL
- Intended for use with gooseneck microphones mounted on lecterns,
pulpits, conference tables and similar surfaces.
- Effectively isolates microphone from noise, shock and vibration
transmitted through the mounting surface.
- Eliminates pickup of low-frequency resonances caused by
mechanical coupling.
DESCRIPTION
The Audio-Technica Shock Mount for Unipoint Series Gooseneck
Microphones is designed to secure the Audio-Technica Unipoint
series gooseneck microphones onto podiums, desktops, etc. The
AT8662 effectively isolates the microphone from noise, shock and
vibration transmitted through the mounting surface and eliminates
pickup of low-frequency resonances caused by mechanical coupling.
Ideal for use with 19mm diameter gooseneck and quick-mount type
microphone using industrial standard XLRM 3-pin type connectors.
B
C
3
x
1
2
0
˚
A
MOUNTING DIMENSIONS
A1.5 mm pilot holes 3 places on 58.2mm circle.
B51 mm thru-hole for mount clearance.
C Outsideedgeofange,71.0mmdiameter.
FRONT

FORM No. ATGC-L0314-13-C
Machida • Tokyo • Japan
桌面式防震话筒座 (适用于 Unipoint 系列鹅颈话筒)
AT8662
- 适合于讲台、论坛、会议桌面或其他同类的平面上，配置
鹅颈式话筒安装使用。
- 有效隔话筒安装面上，因受撞击和震动出现的噪音。
- 消除所接收到因机械性耦合而引起的低频共振。
说明
此鐵三角桌面防震话筒座，主要为Unipoint系列的鹅颈话筒
而设计。AT8662设有防震绝缘胶，能有效减低安装面上的
撞击和震动，并消除所收到因机械性耦合而引起的低频共
振噪声。此话筒座配合19mm直径鹅颈式3针卡农公头的会
议话筒后，非常适合使用在演讲、教学、会议、论坛的场
合使用。
安装
1. 定下和標记出话筒座的安装位置中心点。
需预留足够空间给话筒座
的凸缘外边，并确定在该位置上没有实质的阻碍。
2. 使用一个直径 51.0mm 的开孔器，开出一个足够把话筒座套下的
通孔。
3. 把话筒座套下於通孔中，并标记出3个螺丝孔的位置。
在标记
3
个
螺丝孔前，请确定话筒座是放置于“中心”点中。
4. 使用直径 1.5mm 的小钻咀，在3个螺丝孔位置上钻下3个导孔，再
装上3枚螺丝把话筒座固定。
5. 话筒座安装好後，把话筒套在防震圈的中央，并预留足够的连接线
松弛度，以提供有效的防震效能。
兼容话筒型号
UniPoint® 系列 AT859QMLa
U857Q U857QU
U857QM U857QMU
U857QL U857QLU
U857QSU
U859QL
B
C
3
x
1
2
0
˚
A
底座架尺寸
A置于直径 58.2 mm 圆形上的 3 个直径 1.5 mm 导孔。
B直径 51 mm 的通孔，可把话筒座套下。
C直径 71.0 mm 的凸缘外边。
前方