Automationdirect.com Productivity 2000 P2-08ADL-2 User manual

1
Sales 800-633-0405 www.productivity2000.com
Terminal Block sold separately, (see wiring options on page 5).
Warranty: Thirty-day money-back guarantee. Two-year limited
replacement. (See www.productivity2000.com for details).

®
WARNING: To minimize the risk of potential safety problems, you should
follow all applicable local and national codes that regulate the installation
and operation of your equipment. These codes vary from area to area and
it is your responsibility to determine which codes should be followed, and to
verify that the equipment, installation, and operation are in compliance with
the latest revision of these codes.
Equipment damage or serious injury to personnel can result from the
failure to follow all applicable codes and standards. We do not guarantee
the products described in this publication are suitable for your particular
application, nor do we assume any responsibility for your product design,
installation, or operation.
If you have any questions concerning the installation or operation of
this equipment, or if you need additional information, please call Technical
Support at 770-844-4200.
This publication is based on information that was available at the time
it was printed. At AutomationDirect.com®we constantly strive to improve
our products and services, so we reserve the right to make changes to
the products and/or publications at any time without notice and without
any obligation. This publication may also discuss features that may not be
available in certain revisions of the product.
Removable Terminal Block Specifications
Part Number P2-RTB P2-RTB-1
Number of
positions 18 Screw Terminals 18 Spring Clamp Terminals
Wire Range
30–16 AWG (0.051–1.31 mm²)
Solid / Stranded Conductor
3/64 in. (1.2 mm) Insulation Maximum
1/4 in (6–7 mm) Strip Length
28–16 AWG (0.081–1.31 mm²)
Solid / Stranded Conductor
3/64 in (1.2 mm) Insulation Maximum
19/64 in (7–8 mm) Strip Length
Conductors “USE COPPER CONDUCTORS, 75ºC” or equivalent.
Screw Driver
Width 0.1 in (2.5 mm) Maximum*
Screw Size M2 N/A
Screw Torque 2.5 lb·in (0.28 N·m) N/A
P2-08ADL-2 Analog Input
The P2-08ADL-2 Low Resolution Voltage Analog
Input Module provides eight channels for receiving
0–10 VDC signals for use with the Productivity2000
System.
Warning .................................. 1
Removable Terminal Block Specifications. . . . . . . . 1
General Specifications ...................... 2
Input Specifications ......................... 2
Wiring Diagram and Schematic................ 3
Module Installation Procedure................. 4
QR Code ................................. 4
Hot Swap Information ....................... 4
Wiring Options............................. 5
Module Configuration ....................... 5
Linear Scaling ............................. 6
Non-Linear Scaling ......................... 6
*Recommended Screwdriver TW-SD-MSL-1

2Tech Support 770-844-4200www.productivity2000.com
General Specifications
Operating Temperature 0º to 60ºC (32º to 140ºF)
Storage Temperature -20º to 70ºC (-4º to 158ºF)
Humidity 5 to 95% (non-condensing)
Environmental Air No corrosive gases permitted
Vibration IEC60068-2-6 (Test Fc)
Shock IEC60068-2-27 (Test Ea)
Field to Logic Side Isolation 1800VAC applied for 1 second
Insulation Resistance > 10MΩ @ 500VDC
Heat Dissipation 1200mW
Enclosure Type Open Equipment
Agency Approvals UL 61010-1 and UL 61010-2-201 File E139594, Canada & USA
CE (EN 61131-2 EMC, EN 61010-1 and EN 61010-2-201 Safety)*
Module Keying to Backplane Electronic
Module Location Any I/O slot in a Productivity2000 System
Field Wiring Use ZIPLink Wiring System or removable terminal block (not
included). See “Wiring Options” on page 5.
EU Directive
See the “EU Directive” topic in the Productivity Suite Help File.
Information can also be obtained at:
www.productivity2000.com
Terminal Type 18-position Removable Terminal Block
Weight 100g (3.5 oz)
Input Specifications
Input Channels 8
Module Signal Input Range 0–10 VDC
Resolution 13-bit
Data Range 0–8191 counts
Input Type Single-ended (1 common)
Resolution Value of LSB 0–10 VDC = 1.22 mV per count (1 LSB = 1 Count)
Maximum Continuous Overload ±100VDC
Input Impedance >150kΩ
Filter Characteristics Low Pass, -3dB @ 500Hz
Sample Duration Time 6.25 ms per channel
(does not include ladder scan time)
All Channel Update Rate 25ms
Open Circuit Detection Time Zero reading within 100ms
Accuracy vs. Temperature ±75PPM / ºC maximum
Conversion Method Successive approximation
Maximum Inaccuracy 0.5% of range
(including temperature drift)
Linearity Error (end to end) ±0.036% of range
Monotonic with no missing codes
Input Stability and Repeatability ±0.024% of range
Full Scale Calibration Error
(including offset) ±0.097% of range
Offset Calibration Error ±0.097% of range
Max Crosstalk 4 counts / 0.048% of range
External 24VDC Power Required 24VDC (-20% / +25%), 30mA
*Meets EMC and Safety requirements. See the D.O.C. for details.

3
Sales 800-633-0405 www.productivity2000.com
Wiring Diagram Schematic
V1+
COM
V2+
V3+
V4+
V5+
V6+
V8+
V7+
COM
COM
COM
COM
COM
COM
COM
0V
24V+
- +
24 VDC User
Supplied Power
CH1 ADC
CH2 ADC
CH3 ADC
CH4 ADC
CH5 ADC
CH6 ADC
CH7 ADC
CH8 ADC
ISOLATED
ANALOG
CIRCUIT POWER
ISOLATED ANALOG
CIRCUIT COMMON
INTERNAL
MODULE CIRCUITRY
12345678910 11 12 1813 14 15 16 17
- +
24 VDC User
Supplied Power
Voltage Input Circuits
+
3-Wire Voltage
Transmitter
V+
COM
3-Wire Transmitter
4-Wire Transmitter
COM
V+
4-Wire Voltage
Transmitter
Transmitter
Power Supply
AC or DC
+
–
V7+
COM
V8+
Notes for maximum accuracy:
1. Jumper unsused inputs to common.

4Tech Support 770-844-4200www.productivity2000.com
QR Code
Use any QR Code reader application to
display the module’s product insert.
Important Hot-Swap Information
The Productivity2000 PAC supports hot-swap!
Individual modules can be taken offline, removed, and
replaced while the rest of the PAC system continues
controlling your process. Before attempting to use the
hot-swap feature, be sure to read the hot-swap topic in
the programming software’s help file or our online docu-
mentation at AutomationDirect.com for details on how to
plan your installation for use of this powerful feature.
1 Align
with slot
2rotate
to seated
position
Module Installation
WARNING: Do not apply field power until
the following steps are completed. See
hot-swapping procedure for
exceptions.
WIRE STRIP
LENGTH
WIRE STRIP
LENGTH
Step One: Align module
catch with base slot and
rotate module into
connector.
Locked Unlocked
Step Two: Pull top locking
tab toward module face. Click
indicates lock is
engaged.
Step Three: Attach field wiring using the removable
terminal block or ZIPLink wiring
system.
Caution: If possible, remove field power prior to
proceeding. If not, then EXTREME care MUST be taken
to prevent damage to the module, or even personal injury
due to a short circuit from the live terminal block.

5
Sales 800-633-0405 www.productivity2000.com
Module Configuration
8CH, 13-BIT, VOLTAGE, ANALOG INPUT
Using the Hardware Configuration tool in the
Productivity Suite programming software, drag
and drop the P2-08ADL-2 module into the
base configuration.
Select Automatic Module Verification or No
Verification and Enable Hot Swap. If desired,
assign a User Tagname to each input point
(channel) selected and to each Status Bit Item.
Wiring Options
1ZIPLink Feed Through Modules and Cables¹
0.5 m (1.6 ft) cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-RTB20
ZL-RTB20-1
ZL-P2-CBL18
ZL-P2-CBL18-1
ZL-P2-CBL18-2
Terminal Block with pigtail cable
1.0 m (3.3 ft) cable
2.0 m (6.6 ft) cable
ZL-P2-CBL18-1P
ZL-P2-CBL18-2P
3Screw Terminal Block only
P2-RTB
(Quantity 1)
4Spring Clamp Terminal Block only
P2-RTB-1
(Quantity 1)
5Accessories²
ZL-RTB-COM
TW-SD-SL-1
TW-SD-MSL-1
ZL-RTB20
ZL-RTB20-1
2
1.Cable + ZIPLink Module = Complete System
2. ZL-RTB-COM provides a common connection point for power or ground

6Tech Support 770-844-4200www.productivity2000.com
Select the Input and Output tags appropriate
for the application. Convert raw input signals
to engineering units for use in the program, or
convert engineering units to output signals for
control purposes
max
min
min max
12500
0
65535
220
Level Transmitte
rT
ank Level
0
.5
1
1.55
2.25
3
4.55
6.75
7
0
0
0
0
0
0
0
0
1
2
3
4
5
6
6.5
7
0
0
0
0
0
0
0
Level Transmitte
rT
ank Level
7
0
0
0
0
0
0
0
Enter values for each breakpoint in the
table. Each breakpoint will define a
segment of the non-linear scaling.
7
6
5
4
3
2
1
01 2 3 4 5 6 7 8 9
The Scale (Linear) function can be used to:
• Convert analog field input signals from the range which is native to the
analog input module to an application specific range.
• Make other linear conversions in ranges appropriate to the application.
The Scale (Non-Linear) function can be used for Non-Linear applications.
Linear Scaling Non-Linear Scaling
8191

7
Sales 800-633-0405 www.productivity2000.com

8Tech Support 770-844-4200www.productivity2000.com
Document Name Edition/Revision Date
P2-08ADL-2-DS 3rd Ed. 8/20/2019
Copyright 2016, AutomationDirect.com Incorporated/All Rights Reserved Worldwide