Auton AR 19.5-10 User manual

CEILING
DROP-DOWN
MODELS:
The Authority in Custom Motorized Lifts
INSTALLATION MANUAL
CEILING DROP-DOWN
AR 19.5-10
AR 25.5-15
AR 28.5-20
AR 30.5-20
AR 35.5-30
AR 41-35
CEILING DROP-DOWN
WITH SWIVEL
ARS 21.5-10
ARS 27.5-15
ARS 30.5-20
ARS 32.5-20
ARS 37.5-30
ARS 43-45
WWW.AUTON.COM
29102 Hancock Pkwy | Valencia, California 91355
Phone: [phone] | Fax: [phone]
E-mail: [email protected]

A.
B. Connect the molex cords between the lift and the electronic box.
C. Plug power cord into 115VAC outlet.
D. Make sure all wires are routed away from gears and rack
Installation support: We take great pride in knowing that we manufacture the best lift systems in the world. Our design
and production techniques enable simple installation. However, unexpected issues may arise during installation. In the event that you
require assistance, do not hesitate to contact one of our technicians. We will be happy to answer your questions and resolve any problems
you encounter during the installation process. Phone Support: 661-257-9282, ext. 104 • Email Support: [email protected]m
Use the guide below to assemble your new AUTON lift. If your unit came pre-assembled, go to the next page.
Step 1: Testing
Caution:
Do not operate lift while hands are
in close proximity to moving parts.
Contents:
1 - Lift mechanism
1 - Control box
1 - Remote control
2 - Mounting brackets*
4 - Bolts for brackets*
4 - Nuts*
* Pre-installed on CP units - not included on LCD units
OPTION 1:
A. Attach mounting brackets to lift.
B. Place brackets on pre-installed supports
OPTION 2:
A. Attach mounting brackets to lift.
B. Connect mounting brackets to 1/2” threaded ceiling rods
Each application may require various installation techniques. Please contact Auton for additional assistance.
Step 2: Installation
Keep unit free of debris, keep covered prior to installation

Caution:
Dropping or jarring unit by
hitting walls, ceilings, or
other objects may cause
misalignment of lift.
option 1
Installation Diagrams
Shown with wooden box & optional back board support
option 2
A. STARTING POSITION: Turn the bottom screw clockwise to raise the lift’s starting position.
Turn the screw counterclockwise to lower the lift’s starting position.
B. ENDING POSITION: Turn the top screw clockwise to allow the lift to lower more.
Turn the screw counterclockwise to raise the lifts position.
C. To test positioning run the lift approximately 6” in the opposite direction, stop and then reverse lift motion.
*If positioning requires more than 5 cycles of the lift, the built-in thermal overload protector will disable the
motor to prevent overheating and possible damage. The unit will automatically re-set itself within 10-15minutes.
Step 3: Adjust Limit Switches
The Auton lift utilizes limit switches to
control your preferred positioning of the unit.
The limit switches are located on the motor.
The top switch controls the lift’s ending
position and the bottom switch controls
the lift’s starting position.
Turn the adjusting screw with a hex key or flathead screwdriver. To prevent over-adjustment, turn screw
in very small increments. Each full turn of the screw corresponds to 3/8” in travel.
+ -
- +
STARTING POSITION
ENDING POSITION
Using a power tool to adjust the limits will void the warranty.

Step 4: Operation Instructions
Multi-Function Controller
The multi-function remote operates with RF (Radio Frequency)
and IR (Infrared) simultaneously and has 7 buttons.
1) Up – Press and release for up motion
2) Down – Press and release for down motion
3) Left - Press and release for swivel left motion (on swivel models only)
4) Right - Press and release for swivel right motion (on swivel models only)
5) Stop - Press and release for stop motion
6) Preset 1 - Press and release for Preset 1 position (See below to program position)
7) Preset 2 - Press and release for Preset 2 position (See below to program position)
Additional Button Functions:
A) When in motion, press the opposite direction.
The lift will pause for 1 second and then reverse direction.
B) When in motion, press the same button direction.
The lift will stop.
C) When the swivel is not in center position, press the
“Down” button to return to center and stay without retracting.
D) When the swivel is not in center position, press the
“Up” button to return to center and retract to “home” position.
Programming Preset Positions:
The multi-function remote has two
programmable preset buttons. Use buttons
1-5 to move lift to desired position. Once
there, press and hold a preset button for
5 seconds to “learn” preset position. You
will hear a relay click from the receiver
You can also repeat the procedure above
to “relearn” a different preset position.
Easily override the preset position by
using the swivel buttons to move the
swivel to another desired position.
5) Stop
4) Right
1)
Up
2)
Down
7) Preset 2
3) Left
6) Preset 1
Optional Control Method
Connect optional control accessory
to AUX port
IR Control
Connect the IR eye to the EYE port
Dry Contact Operation:
Short desired operation with COM