Infinity Prelude MTS Center User manual

Installation Guide
• Prelude MTS-WB
Wall Brackets for use with Prelude MTSTower
• Prelude MTS-WBC
Wall Brackets for use with Prelude MTS Center
PRELUDE™MTSWALL BRACKETS
Prelude MTS WB/WBC OM 11/15/99 3:18 PM Page 1

–Tower: Remove (2) existing screws in top and (4)
in bottom of SpeakerTower as shown.Feed your speaker cables
through the slot in the Bottom End Cap as shown and connect to
the terminals.Place the Bottom End Cap on the SpeakerTower
bottom.
Center: Attach speaker wire to terminals as described in the
center-channel Owner’s Guide.
STEP 4
BLACK = –
NO STRIPE = –STRIPE = +
RED = +
2PRELUDE MTSWALL BRACKETS
10-32 SOCKET
HEAD SCREWS
REMOVE SHORT
AND REPLACE
WITH LONG
10-32 SOCKET
HEAD SCREWS
PROVIDED
10-32 SOCKET
HEAD SCREWS BOTTOM
END CAP
SPEAKER
CABLES
SPEAKER
CABLES
SPEAKER
CABLES
WALL
BRACKET
BRACKET
COVER
WALL
BRACKET
FLANGES FLANGE
CUTOUTS
–Align Flange Cutouts in Bracket Cover flange with
Wall Bracket flanges and slide Bracket Cover onto Wall Bracket.
Now slide Bracket Cover so that it centers on theWall Bracket.
This should be a tight fit.
TOGGLE SWITCH
VIEWING CUP IN BOTTOM
OF SPEAKER TOWER
High
Pass
Full
Range
Full
Range High
Pass
–Tower Only: When using the tower as a surround
speaker,setToggle Switch in tower cup to“Full Range.”When
using as a front channel,setToggle Switch in tower cup in
bottom to the“Full Range”position.Please consult the
Prelude MTS Subwoofer manual for exceptions to this setting.
STEP 2
STEP 3
WALL
BRACKET
WALL ANCHORS
AND SCREWS
NOT PROVIDED
TOWER
CENTER
– When mounting each bracket to the wall,try and
position it so that you anchor it to wall studs.Be sure to anchor the
bracket firmly to the wall to sufficiently hold the speaker.Use
screw positions as shown in Step1.
STEP 1
Wall-Mounting the Speaker Using theWall Brackets
The customer is responsible for proper selection and use of
mounting hardware and for correctly and safely wall-mounting
the speakers.
Prelude MTS WB/WBC OM 11/15/99 3:18 PM Page 2

–Tower: To mount Speaker
Tower assembly to Wall Bracket
assembly,lift the SpeakerTower
assembly,with the help of another
person,onto theWall Bracket assembly.
Have one person continue to hold the
SpeakerTower assembly on the Wall
Bracket assembly while the other inserts
and tightens one of the (2) provided
5/16-24 Hex Head Bolts into the top.
Make sure you insert and finger-tighten
the top one first to keep the Speaker
Tower assembly from slipping off theWall
Bracket.After the top bolt is tightened,
insert and tighten the other 5/16-24 Hex
Head Bolt in the bottom.
Center: To mount Speaker toWall Bracket
assembly,lift the Speaker,with the help of
another person,onto theWall Bracket
assembly.Have one person continue to hold the Speaker on theWall
Bracket assembly while the other inserts and tightens one of the
(2) provided 5/16-24 Hex Head Bolts into one side.After the first
bolt is tightened,insert and tighten the other 5/16-24 Hex Head Bolt.
3
PRELUDE MTSWALL BRACKETS
SCREW CAP
ALIGNMENT
SLOTS
SCREW
CAPS
SPEAKER
TOWER
10-32 SOCKET
HEAD SCREWS BOTTOM
END CAP
TOP
SPEAKER
BRACKET
BOTTOM
SPEAKER
BRACKET
SPEAKER
CABLES
SPEAKER
CABLES
SPEAKER
CABLES
–Tower: PlaceTop and Bottom Speaker Brackets in
back slots of SpeakerTower top and bottom.Insert (2) longer
10-32 Socket Head Screws provided in each and tighten.Replace
the (2) screws taken out of the front baffle.Press flush into place
2 screw caps to hide holes in front-baffle base.Make sure that
the alignment slots point toward the center to ensure that the
surface curve matches that of the baffle.
STEP 5
5/16-24 HEX
HEAD BOLT
5/16-24 HEX
HEAD BOLT
Center: Place left and right Speaker Brackets in back slots of
Speaker.Insert (2) longer 10-32 Socket Head Screws provided
in each and tighten.
CENTER
SPEAKER
10-32 SOCKET
HEAD SCREWS
LEFT
SPEAKER
BRACKET
RIGHT
SPEAKER
BRACKET
WALL
BRACKET
CAPS
WALL
BRACKET
CAPS
WALL
BRACKET
TOWER
SPEAKER
– Note: If you
wish to angle the speaker
into a permanent position,you
will need to do so and tighten
the 5/16-24 Hex Head Bolts
before you attach theWall
Bracket Caps.Tighten both
bolts securely and attach the
Wall Bracket Caps to the top
and bottom of theWall
Bracket.These will snap
securely into place.
STEP 6
STEP 7
Prelude MTS WB/WBC OM 11/15/99 3:18 PM Page 3

© 1999 Infinity Systems,Inc.,250 Crossways Park Drive,Woodbury,NY 11797 USA [phone] (USAOnly) www.infinitysystems.com
Infinity is a registered trademark of Infinity Systems,Inc.Printed in USA 11/99 Part No.PREMTSWB
Prelude MTS WB/WBC OM 11/15/99 3:18 PM Page 4