Vivo STAND-SIT1BW User manual

Sit to Stand Single Monitor Wall Mount Workstation
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-sit1bw
SKU: STAND-SIT1BW
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2 3
ASSEMBLY STEPS
STEP 1
PACKAGE CONTENTS
TOOLS NEEDED
17.6 lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Keyboard Arm
B(x1)
Monitor Arm
C(x2)
Wall Bracket
N(x1)
Wrench
J (x4)
Bolt
K (x4)
M4x10
L (x4)
M4 Nut
M (x1)
6mm Allen
Wrench
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x1)
VESA Plate
E(x2)
Cable Clip
F (x1)
Thumbscrew
G(x1)
Pad
H (x1)
Pole
I (x1)
Keyboard
Tray
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-A (x4)
M4x12
M-D (x4)
M5x16
M-C (x4)
M5x12
M-B (x4)
M4x16
M-E (x4)
D5 Washer
M-F (x4)
Spacer
Mount
2.2lbs
(1kg)
Keyboard
22lbs
(10kg)
CPU
W-A (x4)
Screw
W-C (x4)
Washer
W-B (x4)
Anchor
OPTION B: Concrete/Brick Wall Installation
Using holes in wall bracket (C) as a guide, mark drilling locations on wall.
Drill 2.4” (60mm) deep holes using a 3/8” (10mm) drill bit and press anchors
(W-B) into holes, then secure the wall bracket with pole mount facing up
using wall screws (W-A) with washers (W-C). Install pole (H) to wall bracket
using two bolts (J).
STEP 2
A
E
MB
E
Slide cable management clips (E) and both keyboard arm (A)
and monitor arm (B) over top of pole (H) as shown in diagram.
Secure both arms using 6mm Allen wrench (M).
OPTION A: Wood Wall Installation
Using holes in wall bracket (C) as a guide, mark drilling locations on wall.
Use of a stud finder is highly recommended. Drill 2.2” (55mm) deep holes
using a 3/16” (4.5mm) drill bit, then secure the wall bracket with pole
mount facing up using wall screws (W-A) with washers (W-C). Install pole
(H) to wall bracket using two bolts (J).

4 5
STEP 3 STEP 5
Slide VESA plate (D) onto arm (B). Secure using thumb screw (F) as shown in diagram.
STEP 6
STEP 4
Attach keyboard tray (I) to arm (A) using M4x10
bolts (K) and M4 nuts (L). Tighten using wrench
(N) and Phillips screwdriver. Place pad (G) on le
or right side of keyboard tray.
OPTION A: Wood Wall
Place wall bracket (C)
on top of pole (H) and
making sure pole is
perfectly straight, mark
drilling locations. Remove
wall bracket and use stud
finder to confirm stud
location. Drill 2.2” (55mm)
deep holes using a 3/16”
(4.5mm) drill bit. Reinstall
wall bracket to pole with
two bolts (J), then secure
the wall bracket using wall
screws (W-A) with washers
(W-C).
OPTION A: Flat Back Monitor
Attach VESA plate (D) to back of monitor using bolts
(M-A, M-C) and washers (M-E).
OPTION B: Curved/Recessed Back Monitor
Attach VESA plate (D) to back of monitor using bolts (M-B, M-D), washers (M-E) and spacers
(M-F).
ø 4.5mm
OPTION B: Concrete Wall
Place wall bracket (C) on top of
pole (H) and making sure pole is
perfectly straight, mark drilling
locations. Remove wall bracket.
Drill 2.4” (60mm) deep holes using
a 3/8” (10mm) drill bit and press
anchors (W-B) into holes. Reinstall
wall bracket to pole with two bolts
(J), then secure the wall bracket
using wall screws (W-A) with
washers (W-C).
W-C
W-A
J
XX
XX
√
1
3
2
C
W-C W- A
J
W-B
C
2
1
XX
√
G
I
L
N
K
TV
TV
TV
D
M- E
M- A
M- C
TV
TV
TV
M- E
M- B
M- D
M- F
D
F
1
2

6 7
STEP 7 Adjust as Desired
STEP 8
Adjust tension in both tilt brackets using 6mm Allen wrench (M) to hold monitor and keyboard at
desired angles. Run cables through cable management clips (E) and store Allen wrench in clip.
Adjust the tension of monitor and keyboard arms using 6mm Allen wrench (M). Remove the bottom
covers as shown in diagram and run cables through. Reattach cable cover.
12
M
M

LAST UPDATED: 03/30/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303