AV123 Strata mini User manual

Enjoyment Guide

Table of Contents
Safety Precautions 3
Thank You for your Strata Mini purchase 4
Unpacking and Product Registration 5
Inventory 5
Getting Started 5
Limited Warranty Coverage 5
Register your Strata Mini speakers at AV123.com 5
Features and Descriptions 6
The Strata Mini 6
Speaker Placement Considerations 7
Front (Left and Right) Speaker Placement 7
Should I “Toe In” the Strata Mini speakers? 8
Connections 9
Speaker Binding Post Connections 9
Powered Subwoofer Connections 9
Speaker Level Inputs 9
Line Level Inputs 10
Connections for Home Theater Users 10
Wiring for Correct Polarity 10
Setup of the Subwoofer Amplier 11
Setting the Subwoofer Level 11
Conguration and Reference Settings 11
Establishing the Reference Levels of the Full Range Speakers 11
Subwoofer Crossover and Phase Adjustments 12
Setting Subwoofer Crossover 12
Setting Subwoofer Phase 13
Caring for your Strata Mini speakers 13
Technical Specications 14
Limited Warranty and Return Policies 15
Service Assistance for Strata Mini loudspeakers 15

Page 3
Safety Precautions
At AV123, we don’t want to see any of our
customers experience the inconvenience
or unfortunate mishap of a precaution that
was ignored. Please review the following
precautions so you may enjoy your Strata
Mini speakers without unnecessary damage or
misuse.
1) If you suspect you have a component failure in
your speakers at any time, please call AV123 for help. Our experts can assist you in diagnosis and, if
necessary, provide you with eld repair parts where applicable. Our goal is your complete satisfaction.
2) Do not lift these speakers if you feel strain or they are just plain too heavy for you. The weight of each
Strata Mini speaker is listed in the Technical Specications section of this manual for your reference.
3) When lifting these speakers, do so with caution. If you need to use a cart or hand truck to move them
around to their nal destination, please do so with care and caution. Odd shaped boxes may require a 2
person lift even if the weight of the box does not seem prohibitive.
4) Do not install these speakers near water (or expose them to water) or any other liquids. If you have
a place in the basement that oods or a leaky roof in certain spots, do not install your Strata Mini
speakers (or any other home entertainment equipment) in that location. Use good judgement, but if
you are not sure if your chosen location is acceptable, chances are you should call us. It never hurts to
ask.
5) Do not poke, prod, or “heavily pet” these speakers. Do not set drinks on them (or it’s just about
guaranteed the drinks will leave a ring and spill too). Do not use the speakers as tables or chairs.
Whenever possible, ask the kids and pets to play elsewhere than on (or directly in front of) the
speakers. All of these suggestions come from many years of experience by our AV123 experts so you
can trust the origin.
6) Do not install these speakers near a heat source such as a oor heater, space heater, replace, stove,
heat register, active volcano, or any other device (including ampliers) that may radiate heat.
7) Plug the electrical power cord for the integrated amplier into a line conditioner or connect to an
unswitched 110VAC wall outlet directly. Do not connect the subwoofer amplier’s power cord into a
“power strip”. This ensures the best performance and avoids power delivery related problems.
8) Do not plug the Strata Mini speaker binding posts into the wall, EVER. Some people think it’s a great
way to test the excursion limits of a low frequency driver but in truth it’s very dangerous. Just hook
them to the amplier outputs as recommended in this manual please.
9) These speakers in a home entertainment environment can easily produce high sound pressure levels
that can impair hearing if you (or other listeners) undergo extended exposure. Use caution when
listening at high volumes and, by all means, please discontinue use if your ears are ringing. If you must
play these speakers at extremely high volumes, we recommend the use of OSHA approved hearing
protection.
10) Please read and follow the instructions in this manual. Keep this manual for future reference.
IMPORTANT!
PLEASE READ THESE
INSTRUCTIONS
CAREFULLY

Page 4
Mark L. Schifter
President
Thank You for your Strata Mini purchase
Dear Home Entertainment Enthusiast,
At AV123, our absolute highest priority begins and ends with
you, the customer. As our valued customer, you can rest
assured that if you’re not 100% satised with your purchase
within 30 days from your original receipt date, you may return
your product(s) for a prompt refund in full (excluding shipping
charges) with no explanation necessary. Coupled with the
expert advice on our website and through our trained advisors,
there is simply not a safer way or place to buy today.
We make every effort to make sure your home entertainment needs are met with the
great products and unbeatable service we offer every single day. Not only do we give
you the tools and the resources to fully evaluate your purchase before your order is
placed, we back this up after the fact by allowing you a full month to audition our
products in your own home before your nal decision is made. AV123 simply does not
engage in misleading and high-pressure sales tactics. In the long run, we know it’s not
the way either one of us wants to do business. We want customers for a lifetime.
The Strata Mini is a dream come true. The hybrid design will astound you with its
ability to be utterly delicate yet deliver visceral impact when asked. This is thanks to its
combination of planar magnetic drivers operating in concert with “selected” cone drivers.
The planar magnetic midrange and tweeter are custom built to our specications along
with the French-designed and renowned Atohm 5.25” mid-bass coupler located in it’s
own critically damped chamber. We hand this off to a custom damped and treated paper
cone 8” woofer - powered by an internal class A/B 350 watt amplier.
We want you to know that The Strata Mini is exquisite in every measure and meaning
of the word. The Strata Mini is designed for intimate settings – not cathedrals. What
you can expect is an emotionally engaging and utterly immersive experience on an
intimate level. The elegantly designed cabinet with real Rosewood veneers, narrow width
(minimizes visual impact) and sloped bafe will be sure to carry an elegant feel to your
room and extend itself gracefully to the visual realm even at rest.
We’ve done our best to provide you with products and services meeting or exceeding
your expectations. However as good as our products are, they do not match our
dedication to each and every sale. Should you
need any further assistance in the future with your
A/V system, you can bet that AV123 will be there
supporting and assisting you as you make your way
to your next level of audio/visual enjoyment.
Mark with his pride and
joy, Granddaughter Gracie
after her performance in
The Nutcracker

Page 5
Unpacking and Product Registration
The Strata Mini speakers should reach you in absolutely perfect condition. If you notice
any shipping damage or other issues upon unpacking the unit, please contact AV123
immediately. We have gone out of our way to ensure the speakers are shipped with the
utmost care, but if that is not the case when they arrive at your door, please do not
hesitate to contact us.
Inventory
Your Strata Mini speakers are carefully hand packaged utilizing molded foam inserts to
protect their ne furniture grade nish. When removing the speakers from the box, hold
the wood sides of the cabinet, rather than the front and back. It is important to save all
the packing materials and the box in case your Strata Mini speakers ever
needs to be moved or shipped back to AV123 for service or repairs.
All Strata Mini speakers include rubber mounting feet, oor spikes, and
hardwood oor protectors in the packaging to decouple the speaker from
whatever type of ooring material you have.
Getting Started
Once you have established that all of your speakers and accessories are present and
accounted for, we ask that you PLEASE READ THIS MANUAL FIRST before installing
and positioning the speakers. We have thoughtfully assembled many useful tips to
maximize the performance of your Strata Mini speakers in your home entertainment
environment.
Limited Warranty Coverage
All products sold through AV123 carry a limited manufacturer’s parts and labor warranty.
All Strata Mini loudspeakers are guaranteed to be free from manufacturer’s defects for
a period of one year from the date of purchase. Make sure that you keep your sales
receipt. It is the only way for AV123 to establish the duration of your limited warranty
and it may come in useful for insurance purposes if your Strata Mini speakers are ever
damaged or stolen.
Register your Strata Mini speakers at AV123.com
Please take a moment to visit AV123.com and register your Strata Mini purchase. When
you go online and register your product, AV123 will extend the warranty by an additional
two years. This, in addition to the 1 year limited warranty is a total of 3 years! This
extended warranty is free simply for registering within 60 days of your purchase. We
urge you to take advantage of this offer. Warranties apply only to the original owner and
are non-transferable. See page 15 for limited warranty details.
Rubber Feet

Page 6
Features and Descriptions
The Strata Mini
• Floor Standing Loudspeaker
• Four Way, Four Driver Direct Radiating System
Cabinet
• South African Rosewood Veneer
• Internal CNC Machined MDF Skeleton
• Folded Vent for Subwoofer Enclosure
Drivers
• Planar Magnetic 1” Tweeter
• Planar Magnetic 8” Midrange
• Atohm 5.25” Midbass Coupler
Amplier
• Built-in 350 Watt Class A/B Subwoofer Amplier
• Adjustable Crossover
• Adjustable Gain
• Variable Phase (0-180 degrees)
• High and Low Level Inputs/Outputs
Passive Crossover Network
• Custom Designed by Danny Richie
• Air Core Inductors
• Polypropylene Capacitors
• Non-Inductive Wirewound Resistors
• Fourth Order Slopes on High Frequencies
• Second Order Slopes on Low Frequencies
Crossover Points
• Subwoofer = 27Hz to User Denable
• 5.25” Mid Bass Coupler = 80Hz to 650Hz
• 8” Planar Magnetic Midrange = 650Hz to 4100Hz
• 1” Planar Magnetic Tweeter = 4100Hz to 35KHz
The cabinet construction
of the Strata Mini
loudspeakers is superbly
executed with the nest
materials and exacting
tolerances
Planar Magnetic Midrange and
Tweeter drivers coupled with
an Atohm 5.25” Midbass driver
create a very intimate, detailed
sound characteristic
The built-in 350 watt
amplier in the base of the
Strata Mini has all of the
features needed to ensure
low, linear sub-bass output
that blends effortlessly
with the other drivers in
the speaker

Page 7
Speaker Placement Considerations
Achieving the best performance from your Strata Mini speakers requires several details
to follow when setting then up in their new environment. Tips and suggestions for the
most desirable placement techniques are listed throughout this section.
Front (Left and Right) Speaker Placement
Regardless of physical placement, always try to place your main speakers (LEFT and
RIGHT) with the tweeter positioned on axis around ear level. This yields excellent sound
quality results. Physical placement of front speakers should be along the same wall of
your listening/viewing room. Although we’ve seen successful installations that didn’t
follow these guidelines, they’re generally more problematic in terms of system response
and accurate theater sound reproduction. Our advice - why re-invent the wheel?
Use the “Rule of Thirds” whenever possible as
a starting guide. This suggests that the best
placement for your LEFT speaker is approximately
1/3 of the way along the wall behind your
speakers. Similarly, the best place for the RIGHT
speaker is usually 2/3 of the way across the same
wall. If at all possible, move the speakers out from
the back wall. Although all rooms are different, we
recommend a minimum wall-to-rear-of-speaker
distance of 3 inches. Whatever distance you nally
select, use a tape measure to make sure that
each speaker is placed at the same distance from the back wall. With that same tape
measure, make sure the speaker-to-listening position is the same for each speaker, too.
If there’s a conict here (as would happen with an irregular wall behind the speakers),
we suggest that you equalize the distance between front of the speakers and your
favorite listening position. If that places one speaker closer to the wall behind it than the
other, don’t be too concerned.
Remember that the “Rule of Thirds” is a basic guideline only. Some acousticians
recommend placing the main (LEFT and RIGHT) speakers so that they form an
equilateral triangle with the prime listening position. This is as close to ideal. Notice
different distances between speakers and left and right sidewalls. It’s worth trying for
this ideal, but don’t get overly concerned if your room doesn’t allow this precision.
Side walls have a major impact on the sound you hear. Ideally, you should not place
your main speakers close to them. Remember that the “Rule of Thirds” gives you a good
starting position, but you should feel free to experiment. Ideally, try not to place
your main speakers so they’re exactly the same distance from the closest side walls. A
bit of asymmetry here is actually preferable. Symmetrical placement generally results in
larger standing waves in the room that reinforce certain frequencies and diminish others.
Back Wall of Room
1/3 2/3
Primary Listening PositionPrimary Listening Position
LEFT RIGHT
Minimum of 3”
from Wall

Page 8
When you take the time to place your speakers properly, you’ll realize better “imaging”
(the apparent lateral placement of individual instruments or voices), and more depth or
“layering”. You’ll hear those advantages because you’ll be avoiding the aural confusion
caused by so-called “rst reections” that complicate our perceptions when speakers are
too close to a wall’s large, at, reecting surface.
Should I “Toe In” the Strata Mini speakers?
That’s a question many enthusiasts ask us at AV123. Some
people like to “toe-in” their main speakers to get better
performance. This simply means aiming both Left and Right
speakers so that they point more towards the prime listening/
viewing position rather than straight ahead. “Toe-in” can improve
imaging and add a sense of spaciousness to the sound. In a 2-
channel system (with no discrete center channel speaker), this is
especially effective in creating a “phantom” center channel effect.
In addition to imaging improvements, toe-in can also change
your speaker’s tonal balance (or timbre).
For that reason, you may want to play with
toe-in to get the most out of your speakers. Some time spent
experimenting here can yield a better match to your room’s acoustic
properties, provide a clearer, more precise phantom center image,
or just better suit your own listening preferences. If you are using
Strata Mini loudspeakers as part of a home theater system and
actually have a center speaker operating in a matrix mode like Dolby
PLIIx, DTS Neo:6, or another “simulated” multi-channel mode, the
toe in positioning can also help blend that center channel.
Back Wall of Room
1/3
Primary Listening PositionPrimary Listening Position
LEFT RIGHT
Minimum of 3”
from Wall
2/3
Maintain the
same distance
to the listener
Back Wall of Room
1/3
Primary Listening PositionPrimary Listening Position
LEFT
RIGHT
2/3
NOT
RECOMMENDED!
Placement in rooms with
odd shaped back walls
should still align the
speaker distances equally
to the listening position.
Don’t rely on electronic
time delay correction to x
these problems whenever
possible as the difference
in room shape cannot
always be accounted for
with a straight time delay.
“Toe In” of Left and Right Speakers
Primary Listening PositionPrimary Listening Position
LEFT
RIGHT

Page 9
Connections
For the best sound quality and signal transfer, AV123 recommends a minimum of 16
gauge high quality, multi stranded, oxygen free copper speaker cables. Speaker wiring
connections are accomplished through the 5-way binding posts.
Speaker Binding Post Connections
Connect the amplier’s LEFT channel outputs to the positive and
negative input terminals of the LEFT Strata Mini speaker, being sure
to observe correct polarity. Connect the amplier’s RIGHT channel
outputs to the positive and negative input terminals of the RIGHT
speaker, again being sure to observe correct polarity. Refer to your
amplier’s connection manual to ensure the component is suitable
for driving 6 Ohm per channel loads.
Powered Subwoofer Connections
Although there is technically no connection necessary to the
driver itself (we’ve already done that part) you do have to choose
connections for the audio input to the Strata Mini’s subwoofer
amplier. There are several ways in which to accomplish this:
Speaker Level Inputs
After careful consideration, we at AV123 have determined that the
very best sounding method for connecting the active subwoofer
with the other speakers in the Strata Mini loudspeaker via high level
inputs is to do the following:
1) Connect the speaker binding posts directly to the outputs of
your main amplier. The left channel from the amplier/receiver
will connect to the LEFT + and - binding post, then the right channel
from the amplier/receiver will connect to the RIGHT + and - binding
post.
2) Next, connect a second pair of speaker wires from each binding
post to the respective RIGHT high level input on the built in
amplier. Using the right channel only is AV123’s recommended
method because leaving the left high level channel open is used
for a noise cancellation trick if the subwoofer amplier experiences
powerline “hum”. See photo at right for an example.
By directly wiring the binding post inputs in parallel to the amplier,
the bottom octaves reproduced by the subwoofer blend smoother
with the output than if an additional passive lter were used.
To
Amplier
Positive
Output
To
Amplier
Negative
Output
Right channel speaker
binding post connectors
(one connection per side)
Not Used
Not Used
Looping the left negative
input to the left negative
output will help in
any situation where
a powerline “hum” is
present

Page 10
Line Level Inputs
If your receiver or preamplier has a set of full range RCA line
outputs that are not already being used, you can connect these into
the LEFT Line Input jack on the left speaker and then the RIGHT
Line Input jack on the right speaker.
Connections for Home Theater Users
If you are using Strata Mini loudspeakers with a home theater receiver that contains
discrete processing (such as Dolby Digital and/or DTS) you may have only a “SUB” line
output to use. If this is the case, you have 3 choices:
1) Check to see if the receiver has full range RCA line outputs available. If so, use these
outputs connected to the “Line Inputs” of the built in amplier and set the front
speaker setting on in the receiver’s setup menu to “LARGE”.
2) Use the full range high level input as described in the previous section, also setting
the front speakers to “LARGE”.
3) Use the SUB output, split with a “Y” adapter to each “Line Input” and take note of the
crossover setting directions when using a SUB output covered in the next section.
When using this connection option, you will have upstream ltering by the crossover
in the preamplier/processor section.
Wiring for Correct Polarity
When connecting the speakers to the amplier you need to observe the proper polarity.
This simply means that you should connect the positive terminal on your receiver or
amplier (may be marked “+” or be colored red) to the positive terminal (red) on your
Strata Mini speaker. Connect the negative terminal on the amplier (“-” or black) to your
speaker’s negative (black) terminal. Don’t worry about damaging anything if you make
a mistake here. Sound quality will suffer but you won’t ruin anything. You can denitely
hear a difference if it gets connected backwards though. It really affects the imaging and
low frequency response in a negative way, so double check your work!!
When connecting the speaker wiring you’ll see that it has two different conductors
- silver and copper colored are the most common. If you can’t see the conductors
themselves, look closely at the insulation. You’ll notice that the insulation over one
conductor is different than that over the other conductor - one will have slight molded
ridges in it, the other will be smooth, for example. It really makes no difference which
one you pick for positive or negative, just be consistent! Other speaker cable may be
marked with designated positive and negative conductors.
Not Used

Page 11
Setup of the Subwoofer Amplier
Proper setup of the subwoofer amplier in Strata Mini loudspeakers ensures that the
blend of low to high frequency will be optimized when you nally sit down to enjoy them.
Setting the Subwoofer Level
Although you can setup levels by ear, accurate calibration of subwoofer
levels relative to the other speakers in the Strata Mini require an SPL
meter. Radio Shack sells a digital meter that works very well for this
purpose (P/N 33-2055) and it’s about $50. Set the meter on ‘slow’ and
“C” weighting. The dial should be set at either 70 or 80 depending on
your preamplier/processor or receiver’s test tone reference output level.
Consult your owner’s manual to determine what reference point your unit
uses (most use 75, so the 70 setting on the meter would be appropriate
in that example). If you do not have a built in test tone generator, you
can use a test CD that contains Pink Noise.
Each range setting on the Radio Shack 33-2055 meter will cover 20dB (10 above and
10 below). So a setting of 70dB would cover between 60-80dB range. If you are using
another meter, consult the owner’s manual for proper operation.
Conguration and Reference Settings
1) Begin by reviewing the calibration menu settings of your receiver or preamplier/
processor. If there is a speaker conguration menu, be sure the outputs for Strata Mini
speakers are set to “LARGE”.
2) Unplug the subwoofer input on each Strata Mini speaker. Exactly how this is done
depends on whether you are using line level or speaker level inputs.
Establishing the Reference Levels of the Full Range Speakers
3) Set the volume control on your preamplier/processor to the “00 dB” level. If your
unit uses a positive number scale for volume instead of a minus-to-plus scale,
just watch the meter until it reaches 75 or 85dB (depending on the recommended
reference level of 70 or 80dB in the receiver or preamplier/processor’s owner’s
manual). Note this volume position because you will need to get back to it shortly.
4) Turn the volume way down and unplug the binding posts inputs that feed the high
frequency speakers on both of the Strata Minis.
Setting Subwoofer Level
5) Reconnect the subwoofer inputs that you disconnected in Step 2 to both Strata Mini
loudspeakers.
6) The crossover on the each Rocket Strata Mini subwoofer should be set between 80Hz
to 100 Hz as a starting point unless you have used the LFE Subwoofer Output on your
preamp/processor) - in which case the crossover will be left at the highest setting.
Radio Shack
Digital SPL
Meter

Page 12
7) Begin by setting the subwoofer level using the dial labeled
“LEVEL” on the built in amplier to 12 o’clock. See diagram at
right.
8) Raise the volume level on the preamplier/processor so the
test tone achieves the reference level you documented in Step
3. An assistant will be very helpful for this process because the
meter location and subwoofer level adjustment location will be
different. Keep in mind, the intended use of the Rocket Strata
Mini loudspeakers are for intimate 2-channel listening so adjust
the subwoofer level accordingly.
9) Once the subwoofer is calibrated to closely match the other
speakers, small adjustments can be made easily using the
subwoofer level control in your processor or receiver. If
you nd the need to go much above +2 or +3 consistently,
we recommend adjusting the level control on each Strata
Mini amplier upward instead and using a lower number for
reference level on the processor.
Subwoofer Crossover and Phase Adjustments
After setting up the system reference levels on each Strata Mini, it’s time to set the
crossover (where applicable) and the phase dial (where necessary). This activity will
round out the effectiveness of the subwoofer a seamlessly blended part of the four way
Strata Mini system!
Setting Subwoofer Crossover
The range of low pass crossover adjustment is 30-150Hz and is labeled “FREQ”. If you
do not have a dedicated output for the subwoofer such as on a home theater receiver,
simply use the respective left and right line outputs into each Strata Mini line input
for the respective channel. For the crossover setting, it is recommended to begin at
the highest setting (150Hz) and slowly dial it down until it seems as if the bass is
anchored in the front drivers rather than just the subwoofer. We strongly recommend
settings around 80Hz-100Hz because this will allow a nice blend with the other Strata
Mini mid and high frequency speakers without making either of them work too hard
with reproducing the bulk of the low frequencies. If you are a traditional 2 channel
enthusiast, this method is the preferred choice. See diagram shown above.
If your preamplier/processor has a dedicated “LFE” or “SUB” output, then you should
leave the crossover set to the maximum setting because the ltering function is handled
upstream in the Dolby Digital/DTS processor. When your processor is not on a Dolby or
DTS source format, it will make the necessary ltering for the LFE output so this input
conguration will yield the best result for that equipment. If you are using Rocket Strata
Mini loudspeakers in a home theater system, this is the method you should use. It is
assumed however that most users of Strata Mini loudspeakers will do so in a strictly 2-
channel environment as described in the previous paragraph.
Crossover, Phase, and Level
adjustments on the built-in
amplier with indications for
“Starting Points” before you
ne tune

Page 13
The easiest way to test different methods and frequencies for crossing over your
subwoofer is by using bass sweeps from the AVIA Guide To Home Theater DVD or
even low frequency sweeps found on many test CDs. Specically, the tones that descend
in frequency from the individual high frequency speakers to the subwoofer are quite
useful and effective. Using your SPL meter, watch for the smallest amount of overall
needle uctuation while you direct and descend the tones from the main speakers to
the subwoofer going around your system. If you are not sure about how to do this or
where to locate the AVIA or other test discs, please call AV123 at [phone] for
assistance or email us at [email protected].
Setting Subwoofer Phase
The knob labeled “PHASE” controls the relative phase of the subwoofer to best reinforce
the other loudspeakers in your system. Always make adjustments with BOTH Strata
Mini subwoofers playing so you adjust in real time. Adjustments to phase will change
the subwoofer interaction with the rest of the Strata Mini speaker system, providing the
least cancellation, and thus the best response in any room. With SPL meter in hand (or,
better yet, on a tripod in the listening position), play an 80Hz tone (for this exercise the
crossover point must be set to 80Hz or above and turn the Phase knob slowly from “0”
to “180.” Watching your SPL meter, select the setting that results in the biggest peaks in
sound pressure levels (i.e. reads highest on the meter). As this subwoofer is contained
in close proximity with the other drivers in the loudspeaker, your main adjustment of
phase will predominately serve to blend the reected energy from the back wall where
the subwoofer faces.
To verify your measurements, go back to the listening position and listen for yourself
using music you know. If the bass from the loudspeaker seems to be coming from the
front speakers rather than noticeably separated from them and reduced in output level,
you have got it right. The optimum setting indicates the least amount of bass wave
cancellation, and should be left alone after setting until the subwoofer or other speakers
in your room are moved, or placement is altered in any way. With front speaker
placement (where the sub faces the wall on the back), the “180” setting is usually best.
Caring for your Strata Mini speakers
Your Strata Mini speakers do not need much exterior maintenance other than an
occasional dusting. Please use care with the black and wood veneer nish and treat
them as you would a piano or ne furniture nish. The black nish on the Strata Mini
speakers can be waxed with automotive carnuba wax if desired. With the satin black
nish, waxing may even increase the gloss of the nish slightly! Wood veneer surfaces
on Strata Minis can be cleaned with a damp cloth (using water) if necessary. We
recommend the 3M Yellow Detail Cloth (part # 39016) for dust on both the black and
wood veneer surfaces as it does not scratch the nish.

Page 14
Technical Specications
Strata Mini
System Description: 3.5 Way, 4 Driver Full Range Speaker
Enclosure Type: Sealed for Midbass, Midrange, and Tweeter
Vented, Rear Firing for Powered Subwoofer
Frequency Response (+/-3dB): 27Hz- 35KHz
Nominal Impedance: 8 Ohms
Sensitivity: 86dB @ 1w/1m
Crossover Points: Subwoofer = User Denable
5.25” Mid Bass Coupler = 80Hz to 650Hz
8” Planar Magnetic Midrange = 650Hz to 4100Hz
1” Planar Magnetic Tweeter = 4100Hz to 35KHz
Subwoofer Amplier
System Description: Class A/B Plate Subwoofer Amplier, Built In
Rated Power: 350 Watts
Input Type: Speaker Level or Preamp Level Single Ended (RCA)
Crossover Frequency: Adjustable, 30Hz- 150Hz
Electrical Power Requirement: User Switchable 110VAC, 60Hz or 220VAC, 50Hz, 10A Receptacle
Fuse Size/Type: 10 A, T10AL 125V
Weight and Dimensions
Raw Weight: 97 lbs each / 44.09 kg each
Shipping Weight: 280 lbs pair / 127.27 kg pair
Dimensions: 11.5” W x 47” H x 13.5” D / 216mm W x 343mm H x 308mm D
On Axis Frequency Response Impedance Response Spectral Decay

Page 15
Limited Warranty and Return Policies
The Strata Mini speakers have been created to perform awlessly for many years with
regular use. As a result of this quality and craftsmanship, AV123 is proud to offer the
following warranty policies to our customers:
• All products sold through AV123 carry a limited manufacturer’s parts and labor
warranty. This is for the piece of mind that, no matter what your purchase, there is
some type of limited warranty on which you can depend. These will always be clearly
stated with the product.
• All Strata Mini loudspeakers are guaranteed to be free from manufacturer’s defects for
a period of one year from the date of purchase. This warranty applies to the original
purchaser of the Strata Mini product(s) and is non-transferrable.
• The Strata Mini warranty does not cover damage by misuse, abuse, neglect,
unauthorized product modication, failure to follow the instructions outlined in this
owner’s manual, failure to perform routine maintenance, damage resulting from
unauthorized repairs, or claims based upon misrepresentations of the warranty by the
seller.
• If you visit av123.com and register your Strata Mini speaker purchase, AV123 will
extend the warranty by an additional two years. This, in addition to the 1
year limited warranty is a total of 3 years! This extended warranty is free simply for
registering within 60 days of your purchase. We urge you to take advantage of this
offer.
Service Assistance for Strata Mini loudspeakers
AV123 will exchange all defective merchandise, including shipping charges to the original
shipment destination, at no charge for up to 60 days after the date of purchase. After
60 days the product must be returned to AV123 for repair only and return shipping costs
are the responsibility of the customer. Please note that BEFORE sending your Strata
Mini speakers in for repair or replacement, you MUST call AV123 and obtain a return
authorization (R/A) number. Before contacting AV123 to begin the R/A process, please
have as detailed a description of the problem(s) you are experiencing and the conditions
under which the problem(s) occur. Once you have obtained the R/A number, you must
print this clearly on the outside of the box so it will be possible to determine from whom
the Strata Mini speaker(s) came once the parcel arrives. Parcels arriving without an R/A
number will be refused and returned freight collect.
Contact Information
Toll Free - [phone] (menu option 2)
Website - www.av123.com
e-mail - [email protected]

Rev 1.3 10/2006
Distributed Exclusively by:
AV123
2150 W. 6th Ave, Suite L
Broomeld, CO 80020
Toll Free - [phone]
Website - www.av123.com
e-mail - [email protected]