AVLink DPS-4 User manual

1x4
DisplayPort
DA
DPS-4
USER MANUAL V1.0
DPS-4
Package ontents-
 1x DPS-4 Unit
 1x User manual
 1x Power adapter DC 12V with lock
 2x screws
 4x foot pads
An thing missed, please contact with our vendor.
Features
 DP 1.2a Compliant.
 Link rate HBR2/HBR/RBR.
 Supports SST or MST.
 Supports 1, 2, or 4 lanes.
 HDCP compliant.
 IN/OUT DP++ interface featuring.
 HDMI 1.4 compliant receiver.
 AC coupled HDMI 1.4 transmitter.
 All 3D formats defined in DP 1.2a and HDMI 1.4
standards.
-1-
Specifications
Function DPS-4
DP Input Connector 1
DP Output Connector 4
LED indicators POWER
Power Adapter (Min.) DC 12V (LOCKING JACK)
DIP SW 3 PIN DIP SWITCH
DSUB-9PIN F/W Upgrade
DP Output Max.
Resolution 4Kx2K@60
DP Cable Distance 5 meters (Max.)
Housing Metal
Weight 460g
Dimensions (LxWxH) 171x120x25mm
FRONT VIEW
1. 3PIN DIP SW
2. F/W Upgrade
3. DP Input Connector
4. Power jack (12V DC In)
REAR VIEW
1. Power LED
2. S stem Reset
3. DP Output Connector1~4
DIP Switch Setting
Select MST or SST mode:
1 2 3 Mode
F/W UPGRADE OFF MST
ON SST
-2-
MST : Multi-Stream Transport, extend mode.
SST : Mirror mode, all the output screen is the same, the
EDID b DP out1 Monitor.
※As the mode select read , please re-open the power.
Technical Specifications Output Signal
DP Out onnector Pin Assignment
Pin #
Signal
Pin #
Signal
1 ML_Lane 0 (p) 11 GND
2 GND 12 ML_Lane 3 (n)
3 ML_Lane 0 (n) 13 CONFIG1
4 ML_Lane 1 (p) 14 CONFIG2
5 GND 15 AUX_CH(p)
6 ML_Lane 1 (n) 16 GND
7 ML_Lane 2 (p) 17 AUX_CH(n)
8 GND 18 Hot Plug Detect
9 ML_Lane 2 (n) 19 Return
10 ML_Lane 3 (p) 20 DP_PWR
DP In onnector Pin Assignment
Pin #
Signal
Pin #
Signal
1 ML_Lane 3 (n) 11 GND
2 GND 12 ML_Lane 0 (p)
3 ML_Lane 3 (p) 13 CONFIG1
4 ML_Lane 2 (n) 14 CONFIG2
5 GND 15 AUX_CH(p)
6 ML_Lane 2 (p) 16 GND
7 ML_Lane 1 (n) 17 AUX_CH(n)
8 GND 18 Hot Plug Detect
9 ML_Lane 1 (p) 19 Return
10 ML_Lane 0 (n) 20 DP_PWR
-3-

Installation
1. Turn off the DP source and DP displa .
2. Connect the DP cable between the DP source and the
“DP IN” port of DPS-4.
3. Connect the DP cable between the DP displa and the
“DP OUT” port of DPS-4.
4. Connect the power cord of DPS-4.
5. Turn on the DP source and displa .
© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or registered
trademarks belonging to their respective companies.
-4-