AVS RM43B-DVR User manual

AVS RM SERIES LCD MONITORS – INSTALL GUIDE
AUGUST 2017
Thank you for choosing the AVS range of LCD monitors. Please ensure installation is carried out by a suitably qualified technician using
industry best practice. All connections to 12/24v should be appropriately fused.
IMPORTANT: Where wiring diagram shows an ACC connection the wire MUST be connected to ACC DO NOT connect to ignition or
constant 12v.
AVS RM43
WIRE COLOUR
FUNCTION
CONNECT TO
RED (ACC)
+12v ACC supply
Appropriately fused +12v switched ACC supply
BLACK
Earth
Good earth source e.g. vehicle body/chassis
YELLOW RCA
AV2 camera input
Reverse camera output. Monitor will auto switch to display this input when a signal is
detected e.g. when the car goes into reverse and powers on the camera. The display will
switch back to AV1 or turn off if there is no signal on AV1.
WHITE RCA
AV1 camera input
Camera output. Monitor will display AV1 until a signal is detected on AV2.
REAR BUTTON
FUNCTION
TOP
Adjust display brightness/contrast up
MIDDLE
MENU – push to enter menu and scroll through functions
BOTTOM
Adjust display brightness/contrast display brightness/contrast down
AVS RM50SM
WIRE COLOUR
FUNCTION
CONNECT TO
RED (ACC)
+12v ACC supply
Appropriately fused +12v switched ACC supply
BLACK
Earth
Good earth source e.g. vehicle body/chassis
PURPLE
Switches to IN2 input
when 12v applied.
Switches off or back
to IN1 (if signal
present on IN1) when
12v removed.
Connect to 12v switching output eg reverse light.
IN1
Video input
Displays input when
video signal is
detected
Connect to switched video source eg reverse camera.
IN2
Video input
controlled by purple
wire
Connect to video source. Monitor will display video when a 12v signal is detected on
purple wire.
REAR BUTTON
FUNCTION
TOP
Adjust display brightness/colour up
MIDDLE
MENU – push to enter menu and scroll through functions
BOTTOM
Adjust display brightness/ colour display brightness/contrast down
AVS RM50SM WIRING DIAGRAM

AVS RM43B
WIRE COLOUR
FUNCTION
CONNECT TO
RED (ACC)
+12v ACC supply
Appropriately fused +12v switched ACC supply
BLACK
Earth
Good earth source e.g. vehicle body/chassis
FEMALE RCA
V2 camera input
Reverse camera output. Monitor will auto switch to display this input when a signal is
detected e.g. when the car goes into reverse and powers on the camera. The display will
switch back to V1 or turn off if there is no signal on V1.
MALE RCA
V1 camera input
Camera output. Monitor will display V1 until a signal is detected on V2 or switch off if no
signal on V1.
AVS RM43B WIRING DIAGRAM
When connecting the power cable please ensure the positive and negative poles are correct otherwise the fuse will blow to protect the
unit.
PARKING LINE PATTERNS
BUTTON
FUNCTION
MENU
MENU – push to enter menu and scroll through functions
UP/DOWN ARROWS
Use to adjust each menu feature
BRIGHTNESS
Adjust the screen brightness between 0-40 (default is 20)
CONTRAST
Adjust screen contrast between 0-40 (default is 20)
COLOUR
Adjust screen colour between 0-40 (default is 20)
PARKING LINE TYPE*
Choose between 1 of 10 patterns*
PARKING LINE X*
Adjust the left/right angle (0 = left, 40 = right, 20 = centre, default)*
PARKING LINE Y*
Adjust the up/down angle (0 = bottom, 40 = top, 5 = default)*
*PARKING LINE ON/OFF
* This feature must be turned ON before you can adjust the other parking line features
LOGO SELECT**
Choose a start-up logo (VW, Toyota, Hyundai, Nissan, Mazda, Kia, Honda, Suzuki, Chev, Ford)
** LOGO ON/OFF
** This feature must be turned ON before you can choose a logo
RESET
Push up arrow to confirm, resets to factory default values on all menu items
AVS RM43M
WIRE COLOUR
FUNCTION
CONNECT TO
RED (ACC)
+12v ACC supply
Appropriately fused +12v switched ACC supply
BLACK
Earth
Good earth source e.g. vehicle body/chassis
FEMALE RCA
V2 camera input
Reverse camera output. Monitor will auto switch to display this input when a signal is
detected e.g. when the car goes into reverse and powers on the camera. The display will
switch back to V1 or turn off if there is no signal on V1.
MALE RCA
V1 camera input
Camera output. Monitor will display V1 until a signal is detected on V2 or switch off if no
signal on V1.

AVS RM43B-DVR
WIRE COLOUR
FUNCTION
CONNECT TO
RED (ACC)
+12v ACC supply
+12v switched ACC or ignition on supply
BLACK
Earth
Good earth source e.g. vehicle body/chassis
YELLOW
+12v
Constant 12v supply
FEMALE RCA
V2 camera input
Reverse camera output. Monitor will auto switch to display this input when a signal is
detected e.g. when the car goes into reverse and powers on the camera. The display will
switch back to V1 or turn off if there is no signal on V1.
MALE RCA
V1 camera input
Camera output. Monitor will display V1 until a signal is detected on V2 or switch off if no
signal on V1.
See owners manual for operating instructions
AVS RM43B-DVR WIRING DIAGRAM
AVS RM70M AVS RM70
WIRE COLOUR
FUNCTION
CONNECT TO
RED (ACC)
+12v ACC supply
Appropriately fused +12v switched ACC supply
BLACK
Earth
Good earth source e.g. vehicle body/chassis
GREEN
Switches display to V2
Reverse signal/vehicle reverse light wire (+12v). Use red wire on AVS Camera’s RCA lead
FEMALE RCA
V2 camera input
Reverse camera output. Monitor will auto switch to display this input when a signal is
detected e.g. when car goes into reverse and powers on the camera. The display will
switch back to V1 or turn off if there is no signal on V1.
MALE RCA
V1 camera input
Camera output. Monitor will display V1 until a signal is detected on V2 or switch off if
no signal on V1.
BUTTON
FUNCTION
POWER
Power on/off
+ or Ù
Adjust up
MENU
MENU – push to enter menu and scroll through functions
Includes: brightness, contrast, saturation, language, ,mode (16:9 or 4:3), image rotation, factory reset
- or Ú
Adjust display brightness/contrast down
V1/V2
Manually switch between camera inputs

AVS RM70C
WIRE COLOUR
FUNCTION
CONNECT TO
RED
+12/24v ACC supply
Appropriately fused +12/24v switched ignition on supply
BLACK
Earth
Good earth source e.g. vehicle body/chassis
GREEN
Switches display to C2
Reverse signal/vehicle reverse light wire (+12/24v)
C2 4 pin connector
C2 camera input & power
4 pin camera cable. Monitor will switch to display this input when a signal is
detected on green wire e.g. when the car goes into reverse. Display will switch back
to C2 or turn off if there is no signal on C1.
C1 4 pin connector
C1 camera input & power
4 pin camera cable. Monitor will display C1 until a signal is detected on green wire.
BUTTON
FUNCTION
POWER
Power on/off
+
Adjust display brightness/contrast up
MENU
MENU – push to enter menu and scroll through functions
-
Adjust display brightness/contrast down
V1/V2
Manually switch between camera inputs
AVS RM90C
The AVS RM90C can display up to 4 cameras in a split screen, either any channel full screen, 2 way or 4 way split.
The channels can be switched manually using the buttons on the front panel or remote or can be controlled by each channels input wire
e.g. connect the blue wire to the left turn indicator and mount camera 3 on the left side of the vehicle. When the left indicator turns on
the monitor will display the left side camera. Do not connect any input control wire to permanent power as this will lock the display to
that channel and may damage the monitor.
WIRE COLOUR
FUNCTION
CONNECT TO
RED
+12/24v ACC supply
Appropriately fused +12/24v switched ignition on supply
BLACK
Earth
Good earth source e.g. vehicle body/chassis
GREEN
Switches display to CH2 REVERSE
Reverse signal/vehicle reverse light wire (+12/24v)
BROWN
Switches display to CH1 FORWARD
Forward camera switch (+12/24v)
BLUE
Switches display to CH3 LEFT
Left turn indicator or switch (+12/24v)
GREY
Switches display to CH4 RIGHT
Right turn indicator or switch (+12/24v)
CH2 (REV) 4 pin
connector
CH2 camera input & power
4 pin camera cable. Monitor will switch to display this input when a
signal is detected on GREEN wire. Holds for 3 sec (adjustable in SYSTEM
menu) after signal removed.
CH1 (FWD) 4 pin
connector
CH1 camera input & power
4 pin camera cable. Monitor will switch to display this input when a
signal is detected on BROWN wire. Holds for 3 sec (adjustable in SYSTEM
menu) after signal removed.
CH3 (L) 4 pin
connector
CH3 camera input & power
4 pin camera cable. Monitor will switch to display this input when a
signal is detected on BLUE wire. Holds for 3 sec (adjustable in SYSTEM
menu) after signal removed.
CH4 (R) 4 pin
connector
CH4 camera input & power
4 pin camera cable. Monitor will switch to display this input when a
signal is detected on GREY wire. Holds for 3 sec (adjustable in SYSTEM
menu) after signal removed
BUTTON
FUNCTION
POWER
Power on/off
MODE
Switch between 1/2/3/4 camera display. See options below
MENU
MENU –push to enter menu and scroll through functions. See options below
CH1/<
Manually switch to CH1 camera or adjust left
CH2/>
Manually switch to CH2 camera or adjust right
CH3/Ú
Manually switch to CH3 camera or adjust down
CH4/Ù
Manually switch to CH4 camera or adjust up

MODE OPTIONS
DISPLAYS
FULL SCREEN
CH1, 2, 3 or 4 - full screen
DUAL SPLIT
CH1 & CH2 or CH3 & CH4
3 WAY SPLIT EVEN
CH1 & CH2 & CH3
3 WAY SPLIT LEFT
CH 3 half screen + CH1 & CH2
3 WAY SPLIT RIGHT
CH1 & CH2 + CH4 half screen
4 WAY SPLIT LEFT & RIGHT
CH3 + CH1 & CH2 + CH4
4 WAY SPLIT ¼SCREEN
CH1 + CH2 + CH3 + CH4
MENU OPTIONS
FUNCTION
PICTURE
Adjust brightness/contrast/tint etc
VOLUME
Adjust volume
OPTION
Cam 1-4 on/off
Cam 1-4 mirror. I = mirrored 0=normal e.g. I0I0 CH1 mirror, CH2 normal, CH3 mirror, CH4 normal
SYSTEM
RU (rotation) rotates monitor display for upside down or rear mounting viewed in mirror
Cam 1-4 delay (default 3 sec, adjustable 0-10 sec). Adjusts time display holds on channel after signal
removed from green, brown, blue or black wire.
PRESET
Set system time
Set auto on/off time (requires RED wire to permanent power)
Set sleep time