Avsl chord CG Series User manual

CG SERIES
Guitar Amplifiers
Item ref: CG-10 - 173.044UK
CG-15 - 173.045UK
CG-30 - 173.046UK
CG-60 - 173.048UK
User Manual
Version 1.1
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty

173.044UK, 173.045UK, 173.046UK, 173.048UK User Manual
Introduction
Thank you for choosing our CG series guitar amplifier. Please read this manual prior to use to avoid damage to the item.
The CG range is specifically designed to give the guitar player a practical and powerful amplifier with classic tones.
Warning
To prevent the risk of fire or electric shock, do not expose this appliance to rain or moisture. To prevent electric shock do
not remove the cover. No user serviceable parts inside. Refer servicing to qualified service personnel.
Safety
•Prior to connecting mains, ensure that the supply voltage is correct and the mains lead is in good condition.
•Avoid ingress of water or particles into the enclosure.
•If the mains fuse blows, refer the unit to qualified service personnel
•Keep the unit out of direct sunlight and away from heat sources.
•Place the unit in an upright position during use and storage.
•Keep the unit away from moisture or dusty environments.
Cleaning
Use a soft cloth with a neutral detergent to clean the cabinet, panel and controls.
To avoid damage, do not use solvents to clean this equipment.
Control Panel
Rear Panel
1. INPUT –6.3mm jack (unbalanced)
2. VOLUME –Volume for CLEAN channel
3. BASS + TREBLE –Tone controls for clean channel
4. CH/SEL –Channel switch CLEAN - OVERDRIVE
5. GAIN –Input drive level for OVERDRIVE channel or DRIVE effect
6. DRIVE –Switch for engaging the drive effect
7. VOLUME –Master volume control
8. EQ Section –BASS, MIDDLE (CONTOUR for CG-60) and TREBLE tone controls
9. REVERB –Level control for internal spring reverb effect
10. AUX IN –twin RCA line level input for playback devices like mp3 players etc.
11. FOOT SWITCH –6.3mm jack input for channel footswitch
12. HEADPHONES –6.3mm stereo jack headphone output (mutes the speaker for silent practice)
13. POWER –power switch and indicator
14. SEND/RETURN –Loop for external effects (6.3mm jack, unbalanced)

173.044UK, 173.045UK, 173.046UK, 173.048UK User Manual
Operation
•Connect the guitar to the CG-series amplifier input using a good quality 6.3mm mono jack lead. Otherwise, if effect
pedals are to be used, plug into these first (unless they are to be used in the effects loop) and plug the output from
these to the input of the amplifier.
•Connect the amplifier to the mains using the appropriate mains IEC lead supplied.
•If any external effects are to be used in the effects loop, connect the Send/Return jacks to the input/output of the
unit(s) and power up ready for use.
•Set VOLUME, GAIN and REVERB controls to the minimum (fully anticlockwise) position.
•Turn the BASS, MIDDLE, TREBLE and CONTOUR controls to the mid-way position.
•Switch on the POWER and switch the channel to CLEAN (make sure the DRIVE switch is off for CG-10). For CG-60
and CG-30, this can be achieved by plugging a footswitch into the 6.3mm FOOT SWITCH jack and pressing the
switch.
•Increase VOLUME for the clean channel and play a note, ensuring that the guitar’s volume and tone controls are
turned up. Continue increasing VOLUME until the required signal level is achieved.
•For CG-60, adjusting the left-most BASS and TREBLE controls adjusts the tone for the clean channel.
•Switch the CHANNEL or DRIVE switch to the overdrive channel or effect and turn up the GAIN to the desired drive
level whilst adjusting the VOLUME to balance the output level to suit. Note that higher gain and lower volume can
give more distortion.
•Adjust BASS, MIDDLE and TREBLE controls to achieve the desired tone. On the CG-60, the CONTOUR control adjusts
the response curve of the mid frequencies.
•Turn the REVERB control up to the required level to introduce the internal spring reverb effect to the sound.
•Plugging a line level source into the AUX twin RCA input mixes it with the guitar’s signal without adding overdrive or
tone shaping to the AUX signal. This may be a playback device, such as an mp3 player or CD player or even a drum
machine to play along with.
•Plugging in a pair of headphones to the 6.3mm TRS Phones jack will allow silent practice by muting the speaker
output.
•Before switching off or removing power, turn down the VOLUME controls.
•When not in use, switch off and disconnect from the mains.

173.044UK, 173.045UK, 173.046UK, 173.048UK User Manual
Specifications
CG-60
CG-30
CG-15
CG-10
Power supply
220-250Vac, 50/60Hz (IEC)
Output power @ 8Ω
60Wrms
30Wrms
15Wrms
10Wrms
Speaker unit(s)
12" vintage driver
10" vintage driver
8" vintage driver
6" vintage driver
Input
6.3mm jack
Send/Return Loop
Footswitch input
Phones Out (6.3mm TRS jack)
AUX in (2 x RCA)
Preamp Controls
Gain, Shape, Master
Gain, Master
Gain, Master
Gain, Master
Equalisation
Clean Bass & Treble,
Drive Contour, Bass,
Treble
Bass, Middle,
Treble
Bass, Middle,
Treble
Bass, Middle,
Treble
Dimensions
480 x 530 x 280mm
410 x 380 x
200mm
340 x 325 x
180mm
300 x 290 x
120mm
Weight
17.3kg
12.5kg
7.0kg
4.0kg
Troubleshooting
No output and no Power light
Check POWER switch is on and mains lead is connected properly
Check mains fuse hasn’t blown
Power LED lit but no Output
Check that GAIN, EQ, VOLUME and guitar controls are not turned
fully down
Check that headphones are not left plugged in
Change jack lead to check if faulty, also for Send and Return jacks
Check battery is OK in effects units in the Send/Return loop
Output too distorted
Reduce GAIN & EQ controls and increase Master volume to
compensate
Check that overdrive channel is not selected instead of clean
Output very quiet
Check that GAIN, EQ, VOLUME and guitar controls are not turned
down
Unplug effects from Send/Return loop to check if they are cutting
signal level
Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or
Electronic equipment and should not be disposed with other household or commercial waste
at the end of its useful life. The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted. Copyright© 2021.
AVSL Group Ltd. Unit 2-4 Bridgewater Park, Taylor Rd. Manchester. M41 7JQ
AVSL (EUROPE) Ltd, Unit 3D North Point House, North Point Business Park, New Mallow Road, Cork, Ireland