Key Function
1.In normal display, The key function is call out adjustment display value (DZERO&DSPAN)page
2.Into parameter setting page, the parameter mark&data is alternate display, If need modify data
can press up key into setting procedure, The display is lock parameter data, this time must let off
key about 0.2 sec, press again, the parameter data will increment. (Key Response about 0.2 sec)
Key Function
Into parameter setting page, the parameter mark&data is alternate display, If need modify data can
press down key into setting procedure, The display is lock parameter data, this time must let off
key about 0.2 sec, press again the parameter data will decrement. (Key Response about 0.2 sec)
& Key Function
In setting group or setting page press &
key return normal display,
but if in setting page the
modify data will be lost
No Key in anything In setting group or setting page no key in anything about 2 minutes, return normal display,
Setting page the modify data will be lost
Step
Parameter Mark Description
Parameter Mark
Operation Manual
1 Normal display
Press /FUNC key into P.COD setting page
2 P.COD(Pass code input page)
1.Key in 5 digit pass code with or or key
2.Press key,
the pass code is right into setting group , otherwise
return normal display
3 SYS(System setting group)
ROP(Alarm setting group)
1.Select setting group with key
2.Press key into setting page of selection setting group
Step
Parameter Mark Description
Parameter Mark
Operation Manual
4 SYS(System setting group)
Press key decide SYS setting group , press
key into
DP setting page
4-1
DP(Decimal Point)
Default=0
1.Decide decimal point position with or key (0 to 4)
2.Press key enter data and into DSPL setting page
4-2
DSPL(Display Low Scale)
Default=0
1.Decide display low scale with & & key (
-19999~19999)
2.Press key enter data and into DSPH setting page
4-3
DSPH(Display High Scale)
Default=19999
1.Decide display high scale with & & key (
-19999~19999)
2.Press key enter data and into AVG setting page
4-4
AVG (Average)
Default=1
1.Decide display Average times with & & key (1~99)
2.Press key enter data and into LCUT setting page
4-5
LCUT (Low Cut)
Default=0
1.Decide display low cut with & & key (0~99)
2.Press key enter data and into CODE setting page
4-6
CODE(Pass Code)
Default=0
1.Decide Pass code with & & key (0~19999)
2.Press key enter data and into LOCK setting page
4-7
LOCK(Panel Lock)
Default=NO
1.Decide panel lock with or key (NO or YES)
2.Press key enter data and return SYS setting group
Step
Parameter Mark Description
Parameter Mark
Operation Manual
5 ROP(Alarm setting group)
Press key decide ROP setting group
, press key into
ACT1 setting page
5-1
ACT1(Alarm Active 1 setting
page )Default=HI
1.Decide active 1 with or
key(HI or LO)
2.Press key enter data and into ACT2 setting page
5-2
ACT2(Alarm Active 2 setting
page )Default=HI
1.Decide active 2 with or
key(HI or LO)
2.Press key enter data and into
HYS1 setting page
5-3
HYS1(Alarm Hysteresis 1
setting page)Default=0
1.Decide Hysteresis 1 with or
or
key(0~999)
2.Press key enter data and into HYS2 setting page
5-4
HYS2(Alarm Hysteresis 2
setting page)Default=0
1.Decide Hysteresis 2 with or
or
key(0~999)
2.Press
key enter data and into DEL1 setting page
5-5
DEL1(Alarm Delay 1 setting
page)Default=0
1.Decide delay 1 with or
or
key(0~99.9 s
ec)
2.Press key enter data and into DEL2 setting page
5-6
DEL2(Alarm Delay 2 setting
page)Default=0
1.Decide delay 2 with or
or
key(0~99.9sec)
2.Press
key enter data and into SB setting page
5-7
SB(Start band)
Default=0
1.Decide start band with or
or
key(
-999~999)
2.Press key enter data and into SDT setting page
