THOR E2 User manual

Thor E2
hardware manual
Thor E2 manual, v1.00

Thor E2 manual, v1.002
Technical data
Power Consumption: Idle: 2,5 W; Max: 4,5 W
Interface: Ethernet, Micro SD, 2 x USB Host, 1 x RS485
(DCP)
Battery: CR2032, Lithium 3V
Display interface: 5 Inch LCD, 24 bit colour, 960 x 480 resolu-
tion, Capacitive Multi- touch glass
Inputs: 24 V: 24 x 24 V inputs (I1, I2, I4). Thereof 2 x
24 V inputs with constant 30 mA current for
contactor/brake monitoring.
230 V AC: 2 x 230 V AC for Car light and
Powersupply
Outputs: 24 V: 16 x high side (O1, O2) 350 mA short
circuit protected general purpose 230 V AC:
5 x 5 A, 230 V, relay output
Speaker output: 2 x 2 W
Safety Circuit Input: 6 x 230 V AC inputs

Thor E2 manual, v1.003
Table of content
Safety information
Liability
Thor Engineering GmbH or any of it’s collaboration partners is not liable with
respect to the buyer of this product or to any third parties for damage, loss,
costs or work incurred as a result of accidents, misuse of the product, incorrect
installation or illegal changes, repairs or additions. Claims under warranty are
likewise excluded in such cases. Thor Engineering GmbH accepts no liability
arising from printing errors, mistakes or changes.
Safety Precautions!
»Only trained professionals, that are authorised to work on the equipment,
should install, congure and use this product.
»This product is intended for the elevator industry. It has been designed and
manufactured to be used for its specied purpose only. It must not be used
for any other purpose without Thor Engineering GmbH’s consent.
»The product cannot be modied or altered in any way and should only be
installed and congured strictly following the procedures described in this
manual.
»All applicable health and safety requirements and equipment standards must
be considered and strictly adhered to, when installing and conguring this
product.
»After installing and conguring this product, the operation of the equipment
should be fully tested to ensure correct operation, before the equipment is
returned to normal use.
Technical data 2
Safety information 3
Overview 4
Connections 5
Connections top board 6
Connections bottom board 7
Connections top board 8
Certicate 11

Thor E2 manual, v1.004
Overview
Micro-SD card
Term. CAN1
X24
X10B
X13
X14
Term. CAN2
X23
X22
X21
X12
X20B
X31
X30
X20
X10
USB
X11
X25 - Speaker
CR2032 battery
AUX contact
X16
X15
Ethernet

Thor E2 manual, v1.005
Connections
SC-IN
O3.3/L13
O3.4/K14
O3.1/K11
O3.2/K12
COM
QS NO
QS C
Neutral
Passive
Emergency stop
Landing doors
Car door - A
Car door - B
Door lock
Neutral - Out
Speaker
Speaker

Thor E2 manual, v1.006
Connections top board
Contractor monitoring
8x In-/Outputs
IO1IO1 IO2IO2
Bridging
Bridging
8x In-/Outputs
Inspection pit on/o
Inspection pit down
Inspection pit up
Break monitoring
Emergency rescue on/o
Emergency rescue up
Emergency rescue down
24V GRP
24V
24V
GND
GND
DCP-G
CAN-G
CAN-G
DCP-B
CAN-L
CAN-L
DCP-A
CAN-H
CAN-H

Thor E2 manual, v1.007
Connections bottom board
Door zone
Door zone
Bridging
Bridging
CAN-L
CAN-L
CAN-H
PTC
PTC
Power supply
NC
Neutral
COM
Neutral
NO
Car light

Thor E2 manual, v1.008
Connections top board
For reference use only

Thor E2 manual, v1.009
For reference use only

Thor E2 manual, v1.0010
For reference use only

Thor E2 manual, v1.0011
Certicate

Thor Engineering GmbH
Koblenzer Straße 96
53177 Bonn
Germany
Telephone: +49 (0)228 - 93 39 43 34
E-mail: [email protected]
www.thor.engineering
Contact us: