AXIOM Technology SBC81610 User manual
!
" !
#
!! !
!"
#$
!"
!"
!"
AXIOM is a trademark of AXIOM Technology Co., Ltd.
IBM is a registered trademark of International Business
Machines Corporation.
MS-DOS, and Windows 95/98/NT/2000 are trademarks of
Microsoft Corporation.
Award is a trademark of Award Software, Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel and Celeron, Pentium III are trademarks of Intel
Corporation.
Other brand names and trademarks are the properties
and registered brands of their respective owners.
Table of Contents
Chapter 1 Introduction
Chapter 1 IntroductionChapter 1 Introduction
Chapter 1 Introduction -----------------------
----------------------------------------------
-----------------------1
11
1
Chapter 2 Jumpers and Connectors
Chapter 2 Jumpers and ConnectorsChapter 2 Jumpers and Connectors
Chapter 2 Jumpers and Connectors-----
----------
----- 5
55
5
2.2.1COM2 RS232/422/485 Settings: JP1,JP2,JP3 ..................7
2.2.2DiskOnChip Memory Segment: JP10 .............................8
2.2.3CMOS Clear Jumper: JP9...............................................8
2.2.4Watchdog Trigger Mode Setting: JP8............................8
! "
Chapter 3 Installation
Chapter 3 InstallationChapter 3 Installation
Chapter 3 Installation----------------------
--------------------------------------------
----------------------11
1111
11
#
#$%&&'(
!(
Chapter 4 Hardware Description
Chapter 4 Hardware DescriptionChapter 4 Hardware Description
Chapter 4 Hardware Description -------
--------------
-------15
1515
15
# )
(* )
(%*+$#
(!
),+-! .
/0(/(! "
1$, &
4.7.1Graphic Capabilities....................................................20
4.7.2VGA Connector: CN15 ................................................20
./0!
",2!
&++(
+(
34+%#!
!
($!
)$!+(!
Chapter 5 Display Drivers
Chapter 5 Display DriversChapter 5 Display Drivers
Chapter 5 Display Drivers-----------------
----------------------------------
-----------------25
2525
25
Table of Contents
)( )
),)
Chapter 6 Ethernet
Chapter 6 EthernetChapter 6 Ethernet
Chapter 6 Ethernet ---------------------------
------------------------------------------------------
---------------------------27
2727
27
(
,5/0/06
'5/0/06
Chapter 7 Award BIOS Utility
Chapter 7 Award BIOS UtilityChapter 7 Award BIOS Utility
Chapter 7 Award BIOS Utility------------
------------------------
------------29
2929
29
(*("
(* "
!#*,
$'(*, )
)$'!0,.
(+0
+7#
7.7.1Reload Global Timer Events.........................................45
.++%+!(!
"+!80 .
&,9%1! "
, )&
*- )
'%+7)
':/; )
)/;<0')
Appendix A Watchdog Timer
Appendix A Watchdog TimerAppendix A Watchdog Timer
Appendix A Watchdog Timer----------------
--------------------------------
----------------55
5555
55
Appendix B Connector Pin Assignme
Appendix B Connector Pin AssignmeAppendix B Connector Pin Assignme
Appendix B Connector Pin Assignments
ntsnts
nts57
5757
57
SBC81610 All-in-One CPU Card Series User’s Manual
Introduction !
! "#
"#$"#$
%&%'()!%'*"('(
&+#*,%+&
#"-
#".
%&
"/0//123"#$
SBC81610 All-in-One CPU Card Series User’s Manual
Introduction
*
!$ #%
#" Chipset: VT8601T
#" Bus Clock: 133 MHz
#" CPU: VIA C3-733MHz EBGA
#" L2 Cache: Integrated in CPU
#" BIOS: Winbond 2Mbit PnP Flash BIOS
#" System Memory:
!"3 x 168-pin DIMM sockets
!"Maximum of 1.5GB unbuffered SDRAM
!"Supports unbuffered, Non-ECC SDRAM only
!"Supports PC133 SDRAM module
#" IDE Interface: 2 bus mastering EIDE up to four
devices, Ultra DMA33/66/100
supported
#" FDD Interface: Supports up to 2 drives
#" Serial Ports: Two 16550 UARTs ports with 16 byte as
one RS-232 and one RS-232/422/485
#" Parallel Ports: One parallel port with ECP/EPP/SPP
supported
#" VGA Controller:
!"AGP interface controller integrated in VIA VT8601T
!"Supports CRT displays
!"Extended Screen Resolutions up to 1600x1200
#" Ethernet 1:
!"Onboard Dual RTL8139C 10/100M Ethernet
!"Onboard Wake On LAN (via ATX power supply)
!"Onboard RJ-45 connector
#" USB Interface: 2 USB ports; USB Spec. Rev. 1.1
compliant
#" IrDA: 1 IrDA pin-header for wireless communication
#" Power Management: ACPI
SBC81610 All-in-One CPU Card Series User’s Manual
Introduction /
#" Watchdog Timer:
!"Generates System Reset or Non-Maskable Interrupt (NMI) via
jumper selection
!"64 programmable time interval levels of 0.5~8/5~80/50~800/
100~1600 seconds
#" SSD: Supports M-Systems DiskOnChip®2000 series
#" Power Consumption:
!"+5V 5A, +12V @ 300mA)
(VIA C3-733MHz, 256MB SDRAM)
#" Operating Temperature: 0
oC~60oC (32oF~140oF)
#" Storage Temperature: 20oC~85oC (-4oF~185oF)
#" Operating Humidity: 20%~95%; non-condensing
#" Storage Humidity: 20%~75%
#" Dimensions: 122(W) x 335(L) mm
NOTE:Specifications are subject to change without
notice.
! ##
#"
VIA Chipset Driver
#"
Ethernet Utility and Drivers
#"
VGA Drivers
SBC81610 All-in-One CPU Card Series User’s Manual
Introduction
-
!& '
SBC81610 All-in-One CPU Card Series User’s Manual
Jumpers and Connectors 4
SBC81610 All-in-One CPU Card Series User’s Manual
Jumpers and Connectors
(
$! '()
SBC81610 All-in-One CPU Card Series User’s Manual
Jumpers and Connectors 0
$!$ *#+
15
5
6
Jumper Default Setting
Jumper Setting
JP1 COM2 RS-232/422/485 Setting: RS232 Short 1-2
JP2 COM2 RS-232/422/485 Setting: RS232 Short 3-5, 4-6
JP3 COM2 RS-232/422/485 Setting: RS232 Short 3-5, 4-6
JP6 AT/ATX Settings: AT Short 2-3
JP7 AT/ATX Settings: AT Short 2-3
JP8 Watchdog Timer Mode Setting: Disabled Reserved Open
JP9 Clear CMOS Settings: Normal Short 1-2
JP10 DOC Address Settings: Disable Open
COM2 JP1 JP2 JP3
RS-232 (default) Short 1-2 Short 3-5, 4-6 Short 3-5, 4-6
RS-422 Short 3-4 Short 1-3, 2-4 Short 1-3, 2-4
RS-485 Short 5-6, 7-8 Short 1-3, 2-4 Short 1-3, 2-4
SBC81610 All-in-One CPU Card Series User’s Manual
Jumpers and Connectors
'
!
Options Settings
D0000 D3FFF Short 1-2
D4000 D7FFF Short 3-4
D8000 DBFFF Short 5-6
DC000 DFFFF Short 7-8
Disabled (default) Open
"#$%
Options Settings
Normal (default) Short 1-2
Clear CMOS Short 2-3
&#'()(
"#$
71"#$
Options Setting
NMI Short 1-2
RESET Short 2-3
Disabled (default) Open
SBC81610 All-in-One CPU Card Series User’s Manual
Jumpers and Connectors 8
$!
"#$
9
:
"-&,
Connectors Label Connectors Label
SRAM Memory Interface 1 DIMM0 IrDA Interface Connector CN9
SRAM Memory Interface 2 DIMM1 COM1 Connector CN10
SRAM Memory Interface 3 DIMM2 COM2 Connector CN11
Primary IDE Connector CN7 Secondary LAN Connector CN12
Secondary IDE Connector CN1 Primary LAN Connector CN14
FDD Connector CN2 VGA Connector CN15
Parallel Port Connector CN3 System Fan Connector CN16
Reserved CN4 Ext. PS/2 Mouse Connector CN17
Reserved CN5 Ext. PS/2 Keyboard
Connector CN18
Flat Panel Bezel Connector CN6 Mini-Din Connector for K/B
and M/S CN19
USB Interface Connector CN8 ACPI Connector CN13
SBC81610 All-in-One CPU Card Series User’s Manual
Jumpers and Connectors
!)
SBC81610 All-in-One CPU Card Series User’s Manual
Installation !!
"#$
;
!"Power supply and passive backplane (optional)
!"IBMPC/AT keyboard
!"Display monitor
!"Floppy or hard disk with MS-DOS or Flash Disk emulator
! ))
"#$!('
11,4!*1,/
9<&13
!(1/*1(-1!*'1*4(14!*19<&1
NOTE: Use SDRAM modules with PC100 or PC133
specification when running 66/100MHz CPU bus
speed. With 133MHz CPU bus speed, SDRAM modules
with PC133 specification can be used. You have to
install the Intel Celeron or Pentium III processor
before installing the memory modules.
SBC81610 All-in-One CPU Card Series User’s Manual
Installation
!*
!$ ,,- ../
$1&((6!))
')=-)>
$1&6((
-$1&6!))
:"=>')
')
!"#
SBC81610 All-in-One CPU Card Series User’s Manual
Installation !/
! #+
1. Make sure the power is OFF.
2. Set the configuration jumpers according to the jumper
settings on Chapter 2.
3. Install the SBC81610 CPU card into one of the slots on
the passive backplane. You may allow the SBC81610
to stand alone as a single board computer.
4. Connect the I/O cables and peripherals, i.e. floppy
disk, hard disk, monitor, keyboard, power supply and
etc. to the CPU board.
NOTE: The color of pin one is usually red or blue,
while others are gray.
5. Turn ON the system power.
SBC81610 All-in-One CPU Card Series User’s Manual
!-
