Axvue A1080PT User manual
FEATURES & COMPONENTS
1. Night-Vision LED
2. Lens
3. Microphone
4. Power On/Off
5. Power Indicator
6. Speaker
7. Temperature Sensor
8. DC Jack
9. Wall Mounng Hole
10. Adapter
THIS PRODUCT CAN NOT SUBSTITUE PARENT’S SUPERVISION ON YOUR CHILD.
WARNING
- Store this product out of the reach of babies (at least 3 feets (0.9 m) away from the crib). A strap
wound around the baby’s neck may result in asphyxiaon. Use a safety clip to clamp the power cord
and keep it out of baby’s reach. Do not use other extension cords. Only use the power adapter
provided.
- Do not touch the exposed part if the adapter is connected with power.
- Test regularly before inial use or when change the posion of camera.
- Avoid placing the product in humid place or contacng with liquid. (such as bathtub, sink, etc.)
- Do not apply heat to the product.(such as stoves, radiators, etc.)
- Using the product in venlated place. Avoid placing it on sofas, cushions, beds or other places which
may block venlaon.
- The product only can be operated by adult. Do not allow baby to play with it. Tiny accessories are
contained, please be careful when unpack and install it.
keep the distance
between sensor and body
at least 0.6 inch for
accurate temperature
result
0.6 in
SETUP & USE
3 feet
Figure 1
3 feet
Figure 2
*Up To 2 Cameras:
One monitor can be extended to
two cameras at most.
WARNING
Asphyxiaon Danger: Store this product out of the reach of babies (at least
3 feet away from the crib). A strap wound around the baby’s neck may result in
asphyxiaon. Use a safety clip to clamp the power cord and keep it out of baby’s
reach. Do not use other extension cords. Only use the power adapter provided.
Step 1: Test recepon first, put the camera in a suitable place that will
provide you the best view of your baby in the crib (Note: Do not hang up
the camera firmly unl the inial installaon test is completed). Plug the
adapter into the wall outlet and turn on the camera.
Step 2: Turn on the monitor by pressing and holding the Power / Video
buon for 5 seconds unl “axvue” shows up, then the video will show up
on the screen immediately. If the video does not show up, please refer to
“TO PAIR MONITOR AND CAMERA (ADD CAMERA)” on the next page. If
the video shows up, the inial installaon test is completed, then you can
set up the camera according to the instrucon below.
Set Up Camera: Place the camera on a flat surface, such as a wardrobe or
shelf (Figure 1). Or hang it on the wall (Figure 2). No maer wherever to
place the camera, please make sure to keep it away from the crib for at
least 3 feet and all power cords should be placed behind the camera
properly. Then adjust the angle of the camera lens unl the enre crib
shows up on the display, or adjust it to the best angle that you think to
watch your baby.
Please charge the battery for at least 8 hours before using the product.
Step 1: Place the monitor display in the living room, bedroom or any place you want to watch your
baby. Use an adapter to connect the camera with an electrical outlet.
Step 2: Turn on the monitor by pressing the Power / Video“ ” buon for 5 seconds unl axvue logo
or video shows up on the screen.
Step 3: Press Power / Video“ ” buon to turn off the video if you only need to hear the voice.
Step 4: Turn off the monitor completely by pressing and holding the Power / Video“ ” buon for
5 seconds.
TO USE PLUGGED-IN MODE
Get to know us at: www.axvue.com
Please read the following instrucons and warnings carefully
Keep this instrucon manual for future.
For adult use only.
INSTRUCTION MANUAL
Model - A1080PT
Revised at 10/2020
AXVUE A1080PT Extra Camera
For A1080P/E1080P
FCC INFORMATION
This device complies with part 15 of FCC Rules. Operaon is subject to the following
two condions: (1) The device may not cause harmful interference, and (2) This
device must accept any interference received, including interference that may
cause undesired operaon.
CAUTION
Changes and modificaons not expressly approved by AXVUE may void the users
authority to operate this equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protecon against harmful interference in a residenal installaon.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instrucons, may cause harmful interference
to radio communicaons. However, there is no guarantee that interference will not
occur in a parcular installaon. If this equipment does cause harmful interference to
radio or television recepon, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separaon between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION
1. To comply with the FCC RF exposure compliance requirement, a separaon
distance of 20 cm must be maintained between the antenna of this device and all
persons.
2. This transmier most not be co-located or operang in conjuncon with any other
antenna or transmier.
DO NOT EXPOSE TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPORTANT SAFETY INSTRUCTIONS
• Make sure you read this instrucon carefully before using the product.
• Store this instrucon safely for your future reference.
• Ensure that you read the “Warning” secon of the product package and this instrucon carefully.
• Use the product properly by following this instrucon.
• Wipe the product by wet towel aer you take it down from the wall.
• Avoid possible danger by following manufacturer’s instrucon.
• Do not using the product in humid place or contact with liquid, like bathtub, hand washing sink, kitchen sink, laundry tub,
humid basement, swimming pool, etc.
• Ensure the product is installed in a flat place. Otherwise, it will cause serious personal injury and product damage when
dropped.
• Only follow this instrucon and use installaon tools provided by the manufacturer to set up the product.
• The slots and holes on the product are used for venlaon, please ensure that it is not covered or blocked by other objects.
• Do not place the product on bed, sofa, rug or other similar places, it will block or cover the slots and holes on the product.
Do not place the product in a closed bookcase or shelf unless it has parcular part for venlaon.
• This product should be connected with certain power supply unit, if you are not sure about the power supply system in your
home, please contact with your product dealer and local power supply company. Please refer to the operang instrucon if
you want to operate the product in portable/baery mode or by connecng with other power supply sources.
• Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against
them, paying parcular aenon to cords at plugs, convenience receptacles, and the point where they exit from the product.
• An outside antenna system should not be located in the vicinity of overhead power lines or other electrical lines or power
circuits, it will cause interference for the signal transmission. When installing an outside antenna system, extremely aenon
should be paid to avoid touching such power lines or circuits, otherwise, you will have possible danger of electrical shock.
• Do not overload wall outlet, extension cords or convenience receptacles, this can be cause a risk of fire or electrical shock.
• Do not insert any ny objects into the product’s inside, it may touch dangerous voltage point or cause short-circuit, this can
be cause a risk of fire or electrical shock. Any kind of liquid spillage happens on the product should be avoid.
• Do not maintain the product by yourself as opening and removing the covering, this may expose you to dangerous voltage
or other hazards. Please contact with qualified service personnel for maintaining.
• Unplug the product from wall outlet and contact with qualified service personnel if you have problems as below:
- When the power-supply cord or plug has been damaged.
- If liquid has been spilled, or objects have fallen into the product.
- If the product has been exposed to rain or water.
- If the product didn’t operate normally by following the operang instrucons, please only adjust those controls which are
covered by the operang instrucons. An improper adjustment of other controls may result in product damage,
it will also require extensive work from qualified service personnel to restore the product to its normal operaon mode.
- If the products has been dropped or damaged in any way, or when the product shows a disnct change in
performance - this indicated that the product need to be maintained.
• Replacement parts - When replacement parts are required, be sure the service technician has used replacement parts
specified by the manufacturer or its have the same characteriscs as the original part. Unauthorized substuons may
result in fire, electrical shock or other hazards.
• Safety Check - Upon compleon of any service or repairs to this product, ask the service technician to run safety checks on
the product to confirm that it is in a proper operang condion.
• The product only can be mounted on the wall or ceiling as recommended by the manufacturer.
• The product should be kept away from heat sources, such as radiator, heat registers, stoves or other products (including
amplifier) which can produce heat. 732-A1080PT-0700
AXVUE INC.
Revised at 09/2020
*Any updated or revised version please refer to axvue official website.
AXVUE stands behind all of its products.
If you are not completely sasfied or have any quesons,
please contact us at hps://www.axvue.com
Connect with us:
TO DELETE A CAMERA
1
4
6
DELELT CAM?
NO YES
8
2
TO VIEW ONE CAMERA WITH FULL SCREEN ( SELECT CAMERA )
2
1
Note*
: Under this mode, any changes of camera seng (eg. Talk back, Moon detecon, VOX level
seng, etc.) will only be available for Camera 1.
: Under this mode, any changes of camera seng (eg. Talk back, Moon detecon, VOX level
seng, etc.) will only be available for Camera 2.
TO VIEW TWO CAMERAS WITH SPLIT SCREEN
2
1
The monitor and camera are paired before shipment. If it is unpaired for some reason, please refer
to the following steps:
TO PAIR MONITOR AND CAMERA (ADD CAMERA)
Step 1: Make sure the camera and monitor are in the same place.
Step 3:
Turn on the monitor by
pressing and holding Power /
Video buon for 5 seconds.
Step 2:
Make sure the power adapter is plugged into
camera and turn on the camera by pressing Power
On / Off Switch “ ” buon for 3 seconds.
Red LED stop flashing
Red LED flashs
Step 5:
OK
8
The SCAN, SELECT, ADD, DELETE, VIEW CAMERA opons are only available when mulple
cameras connected with the monitor. Order extra cameras by vising us at
www.axvue.com or search “Axvue Baby monitor” on Amazon.
OK
3
OK
9
OK
3
OK
5
OK
7
OK
3
Step 4:
42
1
6
OK
5
OK
3
OK
7
3s
3s
