Aydin Displays CAMBRIDGE CFP47W1 User manual

CAMBRIDGE
USERS MANUAL
CFP47W1 Large Screen Series
VESA Wall Mount
LCD Monitor User Guide
Document No. 150-CFP-470

150-CFP-470
Page 2
Contents
Important Safety Instructions ………………………………………………... 3
 Safety Precautions …………………………………………………………………...…… 3
 Installation ………………....………………………………………………………….…… 3
 Technical Help ……………………………….…………………………………………… 3
 Cleaning Your Display ……………….…………………………………….……………… 3
Features………………………………………………………………….……........ 4
Package Contents ……….....…………………….……………………………... 4
 Dimension ……………………………………………………………………………….… 6
 Installation ……………………………………………………………………………….… 7
 Power Input …………….…….………………………………………………………….… 7
 Power Interface ………..…….………………………………………………………….… 7
 Connection …………….…..……….……………………..…………………………….… 8
 Single Source Input ………….……………………………………………….................. 8
Operating The Monitor …….…………….……………………………............... 9
 The Side Controller Of The Monitor ……….....……………………..….…………….… 9
 The Remote Controller (RCU) Instructions ……………..…………………………….… 9
 Change The RCU Battery ………………..….………………………….……………..… 10
 Display Mode ……..…………………..………… ……………….……………..… 11
 OSD Menu Function ……..…………………..………………………….……………..… 12
 OSD Operating ……………..……………..….………………………….……………..… 13
Default Setting …………………………………………………………….……... 16
Supported Timing ………..…………………………….………………….……... 17
Specification …………..……………….………................................................ 18
Troubleshooting …………………………………….……….…………………... 19
Compliance ……………………………..…………………….…………………... 19
Appendix ………………………………..…………………….…………………... 20
Appendix II …..…………………………..…………………….………………….. 21

※Please read this user’s manual completely before operating this monitor.
Safety Precautions
To turn off the power of the monitor, press”O” on the main power switch at back cover.
The power standby/on indicator goes off and the set cannot to be turned on/ off by using the POWER
button on the remote control. (To turn on/off the monitor by the remote control, press the main power
switch again and light the power standby/on indicator.)
 When turning off the monitor by pressing the POWER button on the remote control, the main power of
the monitor is not turned off completely.
 To disconnect the monitor completely from power supply, remove the power plug from the outlet.
Press”O”to turn off monitor completely
If the power cord or plug is damaged or becomes hot, turn off the main power switch of
the monitor, make sure the power plug has cooled down and remove the power plug
from the outlet.
Installation (when install the monitor, please follow the instruction on the manual )
Don't install in temperatures exceeding specifications.
If the monitor used in environments with temperatures exceeding specifications, it may cause the case or
other parts be distorted, damaged, overheating or an electric shock.
Don't install in a high-humidity environment exceeding specifications.
This may cause overheating or an electric shock.
TechnicalHelp
When having technical problems, please contact Aydin Displays customer service.
CleaningYourDisplay
Cleaning the surface of the monitor.
 When the surface of the monitor is polluted, please wipe the surface with the cotton or clean cloth
lightly.
 If pollution is not easy to clean out, can use the cloth with 50% of the alcohol .
 Please notice carefully that not to let alcohol enter the monitor, it may cause electrical failures.
150-CFP-470
Page 3

Features
High-resolution HD panel
This monitor supports 1920 x 1080 HDTV format and can display true 16.7M colors, you can enjoy extreme fine
pictures.
MVA system less-reflection black TFT LCD panel
MVAsystem and Black TFT LCD panel offer bright and wide images with clear contrast. Even placed near the
windows, the monitor shows bright and clear image with little reflection. The viewing angles of the monitor are as
wide as 170° both horizontally and vertically, enough to enjoy clear images at any view angle.
Offer varieties of connection
Video system Input:
There are 3 choices of connection RGB Input: There are 2 choices of connection Signal delivery
VIDEO RCA
S-VIDEO Mini Din 4 pin
COMPONENT Mini Din 8 pin
RGB ANALOG D-Sub 15pin
RGB DIGITAL DVI-ID 24pin
RS-232C in D-sub 9pin (Option)
Other functions
 Building the light sensor inside, the monitor will adjust the brightness according to the surrounding light
intensity.
 There are two brightness levels pre-set. Under the bright condition, it will adjust to the bright mode.
Under the dim condition, the monitor will adjust to dim mode automatically.
 Signal source auto detection.
 PIP/ PAP function. Please see the chapter “Display mode ”
 Zoom in/out function.
Package Contents
Unpacking
CFP47W1 is packed by the carton box. During transportation, in order to protect the monitor, CFP47W1 is
packed by cushions to be safe protect and package.
Before unpacking your monitor, prepare a stable, level, and clean surface near a wall outlet for your monitor
first.
Set the LCD Monitor box in an upright position and open from the top of the box before removing the top
cushions.
 Step 1: Remove the white handle and cut the bundle
150-CFP-470
Page 4

 Step 2: Remove the top cushion and take the accessories box out.
Top cushion &
Accessories Box
Bottom cushion
The Monitor
Packing list
Q’ty Item Q’ty Item
1 set CFP47W1 1 pcs DVI-D 24 pin cable
1 pcs Power cord 1 pcs D-SUB 15pin cable
1 pcs User's manual 1 pcs S-VIDEO Mini Din 4 pin cable
1 pcs Remote controller 1 pcs Component Mini Din 8 pin cable
1 pcs RCA cable 1 pcs RS232C D-sub 9pin cable (Option)
150-CFP-470
Page 5

Dimension (Front & Back)
150-CFP-470
Page 6

Installation
Environmental state
Operating temperature︰5℃ ~ 40℃ (Fahrenheit : 41℉ ~ 104℉)
Humidity︰max. 85%
Power Input
Power Cord
AC Power cord
This power cord is used to connect the side controls of the LCD monitor and the wall outlet.
Connect the power cord into main power of the monitor, “│” is power on, “○”is power off.
Input: 100-240V~ 3A 50/60Hz
150-CFP-470
Page 7
Sin
g
le In
p
ut Interface
The side of control
○is
p
ower off
│is power on
Main power –Switch &
AC socket
Power Interface
 Main interface- switch & AC socket. Please see the chapter “Power input ”
 The side controller of the monitor
 The remote control (RCU)

Connection
 Video (RCA ) input
 S-Video input
 Component Y Pb/Pr input
 DVI (DVI-D) input
 RGB (VGA) input
 RS-232C input (option)
Single Source Input
Input Interface
NO. Name Remarks
1 Video-IN input connecter RCA
2 S-video input connecter Mini Din 4 pin
3 Y-Pb-Pr (Y-Cb-Cr) inputs Mini Din 8 pin
4 DVI input connecter DVI-D 24 pin
5 RGB input connecter D-Sub 15 pin
6 Power cord input
7 RS232C-IN input (option) D-Sub 9 pin
The Video Signals Input
You can select Video input form 3 connections below:
Video signals Connection type Signal
Video RCA NTSC/PAL
S-Video 4 pins NTSC/PAL
(Y Pb/Cb Pr/Cr) 8 pins NTSC/PAL
150-CFP-470
Page 8
 Suitable signal is automatically selected.

RGB inputting
You can select RGB input for 2 connections as below:
RGB signals Connection type Signal
RGB Analog VGA 15 pins RGB Analog
RGB Digital DVI-D DVI-D 24 pins RGB Digital
Command delivery Connection type Function
RS-232C (Option) 9 pin communication port
Operating The Monitor
TheSideControllerOfTheMonitor
No. Key Description
1 Power Power Switch ; Power ON/OFF
2 ENTER Activate selection
3 〈 / + Menu right / Value increasing
4 〉/ - Menu left / Value decreasing
5 ＾Menu down
6 ﹀Menu up
7 MENU Enter OSD menu / Exit menu or select
The Remote Control (RCU) Instructions
No. Key Description
1 POWER Power ON / OFF
2 YMenu left
3 △Menu up
4 ENTER Enter
5 AUTO
A
djust clock, phase, H & V position
automatically
6 PIP Picture in picture
7 MENU OSD menu
8 ZMenu right
9 ▽Menu down
10 EXIT Exit and one level up
11 SOURCE Input source selection
12 SWITCH PIP picture switch
1
2
3
4
7
8
9
10
5
6
11
12
150-CFP-470
Page 9
λ OSDLock/UnlockControl
Use control push buttons at side
Lock: Press (Z/+) and (▽) at the same time and OSD will be locked.
Unlock: Press (Z/+) and (▽) at the same time again and OSD will be unlocked.

Use remote controller
Lock: Press Enter, Enter, Exit, Exit, Enter and Exit on the controller by sequence and OSD will be locked.
Unlock: Press Enter, Enter, Exit, Exit, Enter and Exit on the controller by sequence again and OSD will be unlocked.
Change The RCU Battery (RCU option)
(1) (2)
(3)
i. Push down as picture (1) and pull the back cover.
ii. Replace with the new batteries as picture (2), 1 piece Lithium battery(CR2032) make sure
the polarity of batteries are correct.
iii. Place back cover and slide it is as picture (3).
iv. Used batteries need to follow the city rule to discard.
v. Avoid keeping used, old batteries inside the remote control, causing leakage of internal liquid
resulting metal rust or fatal damage to the remote control hand unit.
vi. Battery used according to the instruction
.
CAUTION
 Risk of explosion if batty is replaced by an incorrect type.
 Dispose of used batteries according to the instructions.
150-CFP-470
Page 10