AZEMBLA PERGOLA User manual

106 in (269.3 cm)
89.53 in (227.4 cm)
89.53 in (227.4 cm)
106 in (269.3 cm)
85.5 in (217.3 cm)
93.5 in (237.7 cm)
80.5 in (204.6 cm)
94 in (238.9 cm)
85.5 in (217.3 cm)
93.5 in (237.7 cm)
86.1 in (218.6 cm)
GENERAL INFORMATION
PERGOLA
·Wood Stakes (4)
(temporary support
for string line)
·Level
·Tape Measure
·Cordless dig
·Shovel
1
·Tube of Vinyl Glue
·Step Ladders (2)
·Rubber hammer
·String Line
·Pencil
·Stool or short
ladder
For Assembly Instructions please read QR
code with cell phone or visit:
http://azemblaofamerica.com/pvc-pergola/
Please see back side for contents.
Assembly
Instrucions
Tools needed NOT included
ISCLAIMER: This product is designed to
be used solely and exclusively as a
decorative object. It should not
intended for playing or climbing.

C
E
F
i
B´
A
H
J
D
G
K
art Description
A. 3 x 7/8” profiles (9)
B. 3 x 1½” profiles (4)
B.´ 3 x 1½” profiles (2)
C. 5 ½ x 11½” profiles (2)
D. Snap pin for joining profiles (54)
E. 5x5 post caps (4)
F. 3 x 1½” profile caps (12)
G. 5½ x 11½” profile caps (4)
H. 4x4 post caps (4)
I. 4x4 post (4)
J. 4x4 post bocel (8)
K. Slide buttons (16)
L. Shims (32)
KDJ
FG
BC
E
Hi
Content
2
B
Important: check the inside
of posts for materials.

3
irst step
3 x 1½” profile
5 1
2" x 1½” profile
ELA ASSEBL
K
K
K
CC
KC
K
B´
B´
K
art escription
A. 3 x 7/8” profiles (9)
B. 3 x 1½” profiles (4)
B.´ 3 x 1½” profiles (2)
C. 5 ½ x 11½” profiles (2)
D. Snap pin for joining profiles (54)
E. 5x5 post caps (4)
F. 3 x 1½” profile caps (12)
G. 5½ x 11½” profile caps (4)
H. 4x4 post caps (4)
I. 4x4 post (4)
J. 4x4 post bocel (8)
K. Slide buttons (16)
L. Shims (32)
i
C
B
E
E
E
E
A
HH
H
H
1234
J
8- Locate the K buttons (16), B´ profiles (4) and C profiles (4)
insert the K buttons (8) into the B´ and C profiles.
B´

3
5. Apply a of vinyl glue to the
inside of the end caps and
attach them to the profiles as
shown. Hold the end cap in
place for 30 seconds to allow
the glue to set.
3. Slide the two 3 x 1½”
profiles through the
upper holes
2
2. Slide the two 5½ x 1½”
profiles through the
bottom holes
4
PEGA ASSEB
B´
B´
C
H
C
HC
B
C
C
B´
B´
B´
E
H
F
CG
4- Place the B profiles (4) on the C profiles (2)

5
7- Place the A profiles (9) on the B and B´
profiles (6) until joining them with the D
snaps.
3" x 7
8" profile
6. Organize the distances
between profiles where:
X = 61
4" (15.8 cm)
Y= 163
8" (41.7 cm)
X
X
XX
XX
XX
Y
Y
Y
Y
Y
POA ABY
D
D
A
A
A
CB
B´
B
B
B
B´
C
B´
B´ B
C
A

85
1
2
" (217.3 cm)
85
1
2
" (217.3 cm)
4"
93
9
16
" (237.6 cm)
93
9
16
" (237.6 cm)
2"
4"
2"
89
1
2
"
(227.5 cm)
89
1
2
"
(227.5 cm)
2"
4"
2"
126
3
4
" (321.7 cm) in from corner of post to corner of post.
1- Measure and mark the location of the
post with a string. Diagonal distances
must be the same to ensure a square
installation. Adjust the string lines
accordingly.
AA  A
6
ipos de instalacin
nstalacin bajo
el niel del suelo
nstalacin sobre
el niel del suelo
elleno con tierra para instalacion
temporal y con concreto para
instalacion permanente
nin mecnica

1- Measure and mark the location of the brackets
with string or chalk line. Diagonals distances
must be the same to ensure a square
installation. Adjust the strings lines accordingly.
The inside corner of the chord lines will be the
bottom flange corner of the bracket. Using a
masonry bit, dig holes to allow the installation of
the concrete crews (purchased separately)
2- With the four post brackets plumbed, proceed
to set the 4x4 wood post in place. Secure with the
screws included in the kit. Repeat for all four
posts.
3- To create a perfect fit between the 4”x4”
(8.89cm x 8.89cm) wood post and the interior
cavity of the i vinyl post (4)
4- Install J bocel (4) once the installation of the
i posts (4) is finished 7
1
2
3
4
Calzas
Calzas
Extra material
you will need
(not included)
4x4 steel post base kit (4)
(purchase from local building
center)consult the post base
kit instructions for hardware
requirements, as they pertain
to your application.
HARD FLOOR INSTALLATION
OPTION 1 {
i
J
ISTAATI ISTRUCTIS RA

Concrete
96"
60"
36"
36"
10"
2- Install the 4 wood posts 96" x 3
1
2" x 3 1 2" (not included wood posts).
8
1
2
3
1- dig a hole 10” diameter by 36” deep.
3- Pour the concrete mix into the holes
CONCRETE INSTALLATION
OPTION 2
II ICI P

96"
60"
36"
36"
10"
9
1
2
3
1- dig a hole 10” diameter by 36” deep.
2- Install the 4 wood posts 96" x 3
1
2" x 3 1 2" (not included wood posts).
3- Pour the concrete mix into the holes
GROUND INSTALLATION
OPTION 3
II II P

101
0,3
33,33
3,15
7- se instala el bocel
del tubular de 4x4 una
vez se haya secado el
concreto.
7
pcional
7
8" (2.2cm)
10
5
Post wood
Shims
Post PVC
5. will need to “build” the shims into the post. Near the
bottom and top (purchase at local building center)
6- Insert the wood poles
on the PVC posts, mind
level and plumb before
the concrete sets.
To create a perfect fit
between the 4”x4” (8.89cm
x 8.89cm) wood post and
the interior cavity of the
vinyl post
Secure the PVC
post to the wood
poles with 2 screws
of 2” (50.8 cm) in
7/8” (2.2 cm) from
the base of the
4”X4” PVC post.
6
INSTTIN INSTCTINS P

1 To finish the installation, install the upper part of the pergola that was
previously assembled, on the plumbed and aligned posts. Apply a of
vinyl glue to caps and attach them to the profiles as shown.
11
Contact phone number + 1 305 735 2111 | Email: [email protected]
TAAT TCT EA