Backyard Discovery 1905016B Use and care manual

Made in China INS-1905016B-SADDLEBROOK-ENG 09/21/20
For the most up to date assembly manual,
to register your set, or to order replacement parts please visit
www.backyarddiscovery.com
SAVE THIS ASSEMBLY MANUAL FOR FUTURE REFERENCE IN THE EVENT THAT
YOU NEED TO ORDER REPLACEMENT PARTS.
Model # 1905016B
SADDLEBROOK
WOODEN SWING SET
Owner's Manual & Assembly Instructions
MANUFACTURED BY:
Backyard Discovery
3305 Airport Drive
Pittsburg, KS 66762
800-856-4445
average 2 person assembly time
assembly time may vary based on skill level
WARNING: FOR DOMESTIC USE ONLY.
WARNING
NOT SUITABLE FOR
CHILDREN UNDER 36
MONTHS. SMALL PARTS.

• 18+ Years of Experience Servicing Big Box Retailers and Direct Consumers
• Highly Skilled, Specialized, Courteous, Professional Service Technicians
• Over 140,000 Installations Annually
• White Glove Service
• Satisfaction Guarantee
• Flexible Appointments, including weekends
• Coverage across the nation
Visit www.gocongure.com for more info!
*Installation services are only available to U.S. customers.
With Go Con! gure, we bring you 18 years of experience right to your doorstep.
We service a wide array of indoor and outdoor recreation products that most consumers
don’t have the time or ability to deliver & install themselves.
We do the heavy lifting, so you don’t have to!
*Installation services are only available
to U.S. customers.
INSTALLATION
SERVICES
AVAILABLE!*
Need a helping hand?
Let our team of professionals handle the installation for you!
2

e store where you made your purchase
does not stock parts for this item.
If you have assembly questions or you are missing or
have damaged parts, please call
1-800-856-4445
or visit www.backyarddiscovery.com
Please have the following information ready when you make your call:
• Model Number of the product located on the front of the assembly manual
• Description of the part from the parts list
• Read entire assembly manual, paying special attention to the important tips and safety information.
• Ensure there are no missing pieces by  rst separating and identifying all parts.
• Make sure to check packing material for small parts that may have fallen out during shipment.
• Structures are not intended for public use. The Company does not warranty any of its residential structures
subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar
Commercial Application.
• This manual contains helpful information concerning assembly preparation, installation procedure and
required maintenance.
• Always keep safety in mind as your structure is being built.
• Keep these instructions for future reference.
MISSING A PART?
CALL US BEFORE GOING
BACK TO THE STORE
Please Read This Before Starting Assembly
Owner’s Manual
3

Tracking Number Reference Label
Tracking ID number on the carton and on the bottom of the vertical ID plate are included for tracking purposes associated with warranty claims.
is Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard
Botanical, Adventure Playsets, and Leisure Time Products.
Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. is one (1) year
warranty covers all parts including wood, hardware, and accessories. All wood carries a ve (5) year pro-rated warranty against rot and decay. Refer to the schedule below for charges
associated with replacement of parts under this Limited Warranty. In addition, Backyard Discovery will replace any parts within the rst 30 days from date of purchase found to be
missing from or damaged in the original packaging.
is warranty applies to the original owner and registrant and is non-transferable. Regular maintenance is required to assure maximum life and performance of this product. Failure
by the owner to maintain the product according to the maintenance requirements may void this warranty. Maintenance guidelines are provided in the Owner’s Manual.
is Limited Warranty does not cover:
• Labor for any inspection
• Labor for replacement of any defective item(s)
• Incidental or consequential damages
• Cosmetic defects which do not aect performance or integrity of a part or the entire product
• Vandalism, improper use, failure due to loading or use beyond the capacities stated in the applicable Assembly Manual.
• Acts of nature including but not limited to wind, storms, hail, oods, excessive water exposure
• Improper installation including but not limited to installation on uneven, unlevel, or so ground
• Minor twisting, warping, checking, or any other natural occurring properties of wood that do not aect performance or integrity
Backyard Discovery products have been designed for safety and quality. Any modications made to the original product could damage the structural integrity of the unit leading to
failure and possible injury. Modication voids any and all warranties and Backyard Discovery assumes no liability for any modied products or consequences resulting from failure
of a modied product.
is product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should a Backyard Discovery product be used in public settings. Such use may lead to product
failure and potential injury. Any and all public use will void this warranty. Backyard Discovery disclaims all other representations and warranties of any kind, express or implied.
Vertical ID Plate
Tracking number →
Please read entire booklet completely before beginning the assembly process
Please retain these instructions and your receipt for future reference. Keep them in a safe place where you can refer to them as needed.
In order to provide you with the most ecient service, it is required that you provide us with the part numbers when ordering parts.
For Your Records:
Please take time and ll out the information below. is information will be needed for warranty issues.
Where Purchased:
Date of Purchase:
Installation Date:
Installed by:
Tracking Number:
Product Age Customer Pays
$0 and free shipping
$0 + S&H
$0 and free shipping
All Parts
0-30 days from date of purchase
31 days to 1 year
Wood Rot and Decay Only
1 year
2 year
3 year
4 year
5 year
20% + S&H
40% + S&H
60% + S&H
80% + S&H
Over 5 years 100% + S&H
Pro Rated Part Replacement Schedule
Owner’s Manual Limited Warranty
4

NOTE:
Your Children’s Safety Is Our #1 Concern!
Observe the following statements and warnings to reduce the likelihood
of serious or fatal injury. Please review these safety rules regularly with
your children.
WARNING:
BURN HAZARD
• Pay special attention to plastic and metal surfaces as
they may be hot enough to cause burns.
• Always check the temperature of the product before
letting your children play on it.
• Remember that the product may cause burns if left
in direct sunlight.
• Always be aware of the sun and weather conditions,
and do not assume that the equipment is safe
because the air temperature is not very high.
• Children MUST NOT use this playcenter until unit has
been completely assembled and inspected by an adult
to ensure set has been properly installed and anchored.
• Equipment is recommended for use by children 3 to 10
years of age.
• This Playcenter is designed for speci c number of
occupants whose combined weight should not exceed
the designated weight on the elevated  oor or the
swing area. The total unit capacity is outlined in the
Basic Setup Dimensions section of instruction manual.
The maximum fall height and recommended play area is
also available in the Basic Setup Dimensions section of
the manual for the speci c unit.
• On-site, continuous adult supervision is REQUIRED.
MOST SERIOUS INJURIES AND DEATHS ON PLAYGROUND
EQUIPMENT HAVE OCCURRED WHILE CHILDREN WERE
UNSUPERVISED!
• DO NOT allow children to walk close to, in front of,
behind, or between moving swings or other moving
playground equipment.
• DO NOT let children stand on swings.
• Children should NOT twist the chains and ropes and
should not loop them over the top support bar, this
could reduce the strength of the chain or rope.
• DO NOT let children push empty seats. The seat could
hit them and cause serious injury.
• Instruct and teach children to sit in the center of the
swings with their full weight on the seats.
• DO NOT allow children to use the equipment in a
manner other than intended.
• Instruct children to ALWAYS go down slides feet  rst.
Never slide head  rst.
• Instruct children to LOOK before they slide to make sure
no one is at the bottom.
• DO NOT allow children to run up a slide, as this
increases their chances of falling.
• DRESS CHILDREN APPROPRIATELY. (Examples would
include wearing well- tting shoes and the avoidance of
ponchos, scarfs, and other loose- tting clothing that is
potentially hazardous while using equipment).
• DO NOT allow children to climb when the equipment is wet.
• Children should NEVER jump from a fort deck. They
should always use the ladder, ramp or slide.
• Children should NEVER be allowed to crawl or walk
across the top of monkey bars.
• DO NOT allow children to crawl on top of a fort roof.
• Verify that any suspended climbing ropes, chain, or cable
are secured at both ends and that they cannot be looped
back on themselves as to create an entanglement hazard.
•DO NOT let children attach items to the playground
equipment that are not speci cally designed for use
with the equipment. Items such as, but not limited to,
jump ropes, clothesline, pet leashes, cables and chain
can cause a strangulation hazard.
• Children should NEVER wrap their legs around swing chain.
• DO NOT allow children to slide down the swing chain.
• Instruct children to remove their bike or other sports
helmet before playing on playground equipment.
Owner’s Manual Operating Instructions and Safety Warnings
5

Positioning Your Playcenter
• e playcenter is designed to be installed on a level
surface by an adult with an adult helper. Place
in a at area of your yard to minimize ground
preparation.
• Choose a level location for the equipment. is can
reduce the likelihood of the play set tipping over and
loose-ll surfacing material washing away during
heavy rains.
• Place the equipment not less than 6  (1.8 m) from
any structure or obstruction such as a fence,
garage, house, overhanging branches, laundry lines,
or electrical wires.
• Provide enough room so that the children can use the
equipment safely. For example, for structures with
multiple play activities, a slide should not exit in front
of a swing.
• It is a good idea to place your playcenter in an area that
is convenient for adults to watch children at play.
• Create a site free of obstacles that could cause injuries
– such as low overhanging tree branches, overhead
wires, tree stumps and/or roots, large rocks, bricks
and concrete. Additional suggestions in the Suggested
Playground Surfacing Section.
• Do not build your playset on top of surfacing material.
• Locate bare metal platforms and slides out of direct
sunlight to reduce the likelihood of serious burns. A slide
that faces north will receive the least direct sunlight.
• Separate active and quiet activities from each other.
For example, locate sandboxes away from swings or
use a guardrail or barrier to separate the sandbox
from the movement of the swings.
Suggested Playground Surfacing
• Do not install home playground equipment over
concrete, asphalt, packed earth, grass, carpet, or any
other hard surface. A fall onto a hard surface can
result in serious injury to the equipment user.
• Do not install loose ll surfacing over hard surfaces
such as concrete or asphalt.
• Shredded bark mulch, wood chips, ne sand and ne
gravel, are added as shock absorbing materials aer
assembly. If used properly these materials can absorb
some of the impact of a child’s fall.
• All surface material should extend a minimum of 6
(1.8m) feet in all directions around the play area.
• Do not apply playground surfacing until aer the unit
is completely constructed. Playset should not be built
on top of surfacing.
• Use containment, such as digging out around the
perimeter and/or lining the perimeter with landscape
edging.
• Installations of rubber tiles or poured-in-place
surfaces (other than loose-ll materials) generally
require a professional and are not “do-it-yourself ”
projects.
• Shall use Playground Surfacing Materials (other than
loose-ll material) which comply with the safety
standard ASTM F1292 Standard Specication of
Impact Attenuation of Surfacing Materials within the
Use Zone of Playground Equipment.
The following chart explains the fall height in feet from which a life threatening head injury would not be expected
Critical Heights in feet (m) of Tested Materials
Material Compressed Depth
6" (152mm) 9" (228mm) 12" (304mm) to 9" (228mm)
Wood Chips 7' (2.13m) 10-12' (3.0-3.6m) 11' (3.35m) 10' (3.05m)
Double-Shredded Bark Mulch 6' (1.83m) 10-12' (3.0-3.6m) 11' (3.35m) 7' (2.13m)
Engineered Wood Fibers 6' (1.83m) 7' (2.13m) >12' (3.66m) 6' (1.83m)
Fine Sand 5' (1.52m) 5' (1.52m) 9' (2.74m) 5' (1.52m)
Coarse Sand 5' (1.52m) 5' (1.52m) 6' (1.83m) 4' (1.22m)
Fine Gravel 5' (1.52m) 7' (2.13m) 10' (3.05m) 6' (1.83m)
Medium Gravel 5' (1.52m) 5' (1.52m) 6' (1.83m) 5' (1.52m)
Shredded Tires* 10-12' (3.0-3.6m) N/A N/A N/A
Uncompressed Depth
*This data is from tests conducted by independent testing laboratories on a 6-inch depth of uncompressed shredded tire samples produced by four manufacturers. The tests reported
critical heights, which varied from 10 feet to greater than 12 feet. It is recommended that persons seeking to install shredded tires as a protective surface request test
data from the supplier showing the critical height of the material when it was tested in accordance with ASTM F1292.
Please Read This Before Starting Assembly
Owner’s Manual
6

The following information is from the United States
ConsumerProductSafetyCommission’sInformation
Sheet for playground surfacing material; also see
the following website for additional information:
www.cpsc.gov
X3. SECTION 4 OF THE CONSUMER PRODUCT SAFETY
COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY
HANDBOOK9
X3.1 Select Protective Surfacing—One of the most
important things you can do to reduce the likelihood of serious head
injuries is to install shock-absorbing protective surfacing under
and around your play equipment. e protective surfacing should
be applied to a depth that is suitable for the equipment height in
accordance with ASTM Specication F 1292. ere are dierent
types of surfacing to choose from; whichever product you select,
follow these guidelines:
X3.1.1 Loose-Fill Materials:
X3.1.1.1 Maintain a minimum depth of 9 inches of loose-
ll materials such as wood mulch/chips, engineered wood ber
(EWF), or shredded/recycled rubber mulch for equipment up to 8
feet high; and 9 inches of sand or pea gravel for equipment up to 5
feet high. NOTE: An initial ll level of 12 inches will compress to
about a 9-inch depth of surfacing overtime. e surfacing will also
compact, displace, and settle, and should be periodically relled to
maintain at least a 9-inch depth.
X3.1.2 Use a minimum of 6 inches of protective surfacing
for play equipment less than 4 feet in height. If maintained properly,
this should be adequate. (At depths less than 6 inches, the protective
material is too easily displaced or compacted.)
NOTE: Do not install home playground equipment over concrete,
asphalt, or any other hard surface. A fall onto a hard surface can
result in serious injury to the equipment user. Grass and dirt are not
considered protective surfacing because wear and environmental
factors can reduce their shock absorbing eectiveness. Carpeting
and thin mats are generally not adequate protective surfacing.
Ground level equipment such as a sandbox, activity wall, playhouse
or other equipment that has no elevated play surface – does not need
any protective surfacing.
X3.1.3 Use containment, such as digging out around the
perimeter and/or lining the perimeter with landscape edging. Don’t
forget to account for water drainage.
X3.1.3.1 Check and maintain the depth of the loose-
ll surfacing material. To maintain the right amount of loose-ll
materials, mark the correct level on play equipment support posts.
at way you can easily see when to replenish and/or redistribute
the surfacing.
X3.1.3.2 Do not install loose-ll surfacing over hard
surfaces such as concrete or asphalt.
X3.1.4 Poured-In-Place Surfaces or Pre-Manufactured
Rubber Tiles — You may be interested in using surfacing other than
loose-ll materials – like rubber tiles or poured-in-place surfaces.
X3.1.4.1 Installations of these surfaces generally require a
professional and are not “do-it-yourself” projects.
X3.1.4.2 Review surface specication before purchasing this
type of surfacing. Ask the installer/manufacturer for a report showing
that the product has been tested to the following safety standard:
ASTM F 1292 Standard Specication for Impact Attenuation of
Surfacing Materials within the Use Zone of Playground Equipment.
is report should show the specic height for which the surface is
intended to protect against serious head injury. is height should
be equal to or greater than the fall height – vertical distance between
a designated play surface (elevated surface for standing, sitting,
or climbing) and the protective surfacing below – of your play
equipment
X3.1.4.3 Check the protective surfacing frequently for wear.
X3.1.5 Placement — Proper placement and maintenance of
protective surfacing is essential. Be sure to:
X3.1.5.1 Extend surfacing at least 6 feet from the equipment
in all directions.
X3.1.5.2 For to-fro swings, extend protective surfacing in
front of and behind the swing to a distance equal to twice the height
of the top bar from which the swing is suspended.
9is information has been extracted from the CPSC publications
“Playground Surfacing — Technical Information Guide” and “Handbook
for Public Playground Safety.” Copies of these reports can be obtained by
sending a postcard to the: Oce of Public Aairs, U.S. Consumer Product
Safety Commission, Washington, D.C., 20207 or call the toll-free hotline:
1-800-638-2772.
e American Society for Testing and Materials takes no position respecting
the validity of any parent right asserted in connection with any item
mentioned in this standard. Users of this standard are expressly advised
that determination of the validity of any such parent rights, and the risk of
infringement of such rights, are entirely their own responsibility.
e standard is subject to revision at any time by the responsible technical
committee and must be reviewed every ve years and if not revised, either
approved or withdrawn. Your comments are invited either for revision
of this standard or for additional standards and should be addressed to
ASTM Headquarters. Your comments will receive careful consideration at
a meeting of the responsible technical committee, which you may attend.
If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards. 100 Barr
Harbor Drive, West Conshohocken, PA 19428.
APPENDIX A
Please Read This Before Starting Assembly
Owner’s Manual
7

OWNERS SHALL BE RESPONSIBLE FOR MAINTAINING THE LEGIBILITY OF THE WARNING LABELS
At the beginning of each play season
• Tighten all hardware.
• Lubricate all metallic moving parts per manufacturer’s
instructions.
• Check all protective coverings on bolts, pipes, edges,
and corners. Replace if they are loose, cracked, or
missing.
• Check all moving parts including swing seats,
ropes, cables, and chains for wear, rust, or other
deterioration. Replace as needed.
• Check metal parts for rust. If found, sand and
repaint using a non lead-based paint meeting the
requirements of 16 CFR 1303.
• Check all wood members for deterioration
and splinters. Sand down splinters and replace
deteriorating wood members.
• Reinstall any plastic parts, such as swing seats or any
other items that were removed for the cold season.
• Rake and check depth of loose ll protective surfacing
materials to prevent compaction and to maintain
appropriate depth. Replace as necessary.
Twice a month during play season
• Tighten all hardware.
• Check all protective coverings on bolts, pipes, edges, &
corners. Replace if they are loose, cracked, or missing.
• Rake and check depth of loose ll protective surfacing
materials to prevent compaction and to maintain
appropriate depth. Replace as necessary.
Once a month during play season.
• Lubricate all metallic moving parts per manufacturer’s
instructions.
• Check all moving parts including swing seats,
ropes, cables, and chains for wear, rust, or other
deterioration. Replace as needed.
At the end of each season or when
the temperature drops below 32° F
• Remove plastic swing seats and other items as specied by
the manufacturer and take indoors or do not use.
• Rake and check depth of loose ll protective surfacing
materials to prevent compaction and to maintain
appropriate depth. Replace as necessary.
Additional Maintenance
• Check the swing beam and hardware every two
weeks due to wood expansion and contraction. It is
particularly important that this procedure be followed
at the beginning of each season.
• Inspect wood parts monthly. e grain of the wood
sometimes will li in the dry season causing splinters
to appear. Light sand may be necessary to maintain a
safe playing environment. Treat your playset with stain
regularly, to help prevent severe checking/splitting and
other weather damage.
• A waterborne transparent stain has been applied to
your playset. is is done for color only. Once or twice
a year, depending on your climate conditions, you must
apply some type of protection (sealant) to the wood
of your unit. Prior to the application of sealant, lightly
sand any “rough” spots on your playset. Please note this
is a requirement of your warranty.
• Assembling and maintaining the playset on a level
location is very important. As your children play, your
playset will slowly dig its way into the soil, and it is very
important that it settles evenly. Make sure the playset is
level and true one each year or at the beginning of each
play season.
Disposal Instructions
When the Playcenter use is no longer desired, it should
be disassembled and disposed of in such a way that no
unreasonable hazards will exist at the time the unit is
discarded.
Third Party Assembly
Customer may, in their sole discretion, elect to use a
third party person or service to assemble this product.
Backyard Discovery assumes no responsibility or
liability for any charge incurred by the Customer for
any assembly services’. Please see our warranty for
more information about damaged and missing part
replacement coverage. Backyard Discovery will not
reimburse Customer for the price of parts purchased.
IT IS IMPORTANT TO CHECK AND TIGHTEN ALL HARDWARE AT THE BEGINNING AND DURING
THE SEASON AS THEY MAY LOOSEN DUE TO WOOD EXPANSION AND CONTRACTION.
Owner’s Manual Instructions for Proper Maintenance
8

About Our Wood
Backyard Discovery uses 100% Cedar (C. Lanceolata) wood. Although we take great care in
selecting the best quality lumber available, wood is still a product of nature and susceptible to
weathering which can change the appearance of your set.
Your Backyard Discovery structure is designed and constructed of quality
materials. As with all outdoor products it will weather and wear. To maximize
the enjoyment, safety and life of your structure it is important that you properly
maintain it.
What causes weathering? Does it aect
the strength of my product?
One of the main reasons for weathering is the
eects of water (moisture); the moisture content
of the wood at the surface is dierent than the
interior of the wood. As the climate changes,
moisture moves in or out of the wood, causing
tension which can result in checking and or
warping. You can expect the following due to
weathering. ese changes will not aect the
strength of the product:
1. Checking is surface cracks in the wood along the
grain. A post (4” x 4”) will experience more checking
than a board (1” x 4”) because the surface and
interior moisture content will vary more widely than
in thinner wood.
2. Warping results from any distortion (twisting,
cupping) from the original plane of the board and
oen happens from rapid wetting and drying of the
wood.
3. Fading happens as a natural change in the wood
color as it is exposed to sun-light and will turn grey
over time.
How can I reduce the amount of
weathering to wood product?
1. Your wood product is coated with a water-
based stain. Sunlight will break down the coating,
so we recommend applying a water repellent or
stain on a yearly basis (see your local stain and
paint supplier for a recommended product). You
must apply some type of protection (sealant)
to the wood of your product. Please note this
is a requirement of your warranty.Most
weathering is just the normal result of nature
and will not aect safety. However if you are
concerned that a part has experienced a severe
weathering problem please call our customer
service department for further assistance.
2. Inspect wood parts monthly. e grain of
the wood sometimes will li in the dry season
causing splinters to appear. Light sanding may
be necessary to maintain a safe environment.
Treating your Product with protection (sealant)
aer sanding will help prevent severe checking/
splitting and other weather damage.
Owner’s Manual Instructions for Proper Maintenance
9

Protrusion Hazard
Proper Hardware Assembly
1/8”
CorrectIncorrect
Bolt and Barrel Nut Assembly
Insert barrel nut through the lock washer and press the pair
through the provided hole. Insert your bolt through the second
lock washer and insert the pair into the provided hole opposite
from the barrel nut. Turn clockwise to thread into the barrel nut.
Do not completely tighten until instructed. LOCK WASHER
BARREL NUT
LOCK WASHER
BOLT
Bolt and T-Nut Assembly
Tap T-nut into the provided hole. Insert your bolt through the
lock washer and insert into the provided hole opposite from the
T-Nut. Turn clockwise to thread into T-nut. Do not completely
tighten until instructed.
T-NUT
LOCK WASHER
BOLT
Lag Assembly
Normally there will be a pre-drilled pilot hole on assemblies
that require a Lag Screw. If there is no pilot hole, line up the two
boards as they are to be attached and use the factory drilled hole
as a guide to drill another pilot hole into the adjoining board.
is will keep the wood from splitting. Only a lock washer is
required for steps with Lag Screws. LOCK WASHER
LAG SCREW
Owner’s Manual Assembly Tips
If you see exposed
threads and your bolt
protrudes beyond the
T-Nut you may have over
tightened the bolt or
used incorrect hardware.
If you’ve overtightened,
remove the bolt and add
washers to eliminate the
protrusion.
10

Hardware Identication
Hardware bags are printed with
a seven digit alpha-numeric part
number. During assembly you only
need to reference the last three
digits of the part number as noted
in each step. This will make  nding
the correct hardware easier.
BOLT WH
5/16 x 1-3/4 - H100378
378
(x2)
ASSEMBLY TIP:
Keep an eye out for these boxes which will contain helpful pictures and information making
the assembly process as quick and painless as possible.
Sorting Wood
Sorting Hardware
When removing the wood from the boxes we recommend arranging them by part number before you begin
assembly. This will allow for faster assembly and easily identify any parts that may be missing or damaged.
To help with assembly we recommend sorting your hardware bags with the seven digit alpha-numeric number
printed on the bags or by hardware type (i.e. bolts, nuts, etc.). Organizing your hardware will make assembly easier.
NUT BARREL
H100545
SCREW
H100695
T-NUT
H100699
WASHER FLAT
H100706
BOLT HEX
H100716
BOLT
H100718
SCREW PWH
H100742
G2
G1
F2
F1
E1
E2
192(x2)
199(x2)
198(x2)
378(x2)
Assembly Tips
Owner’s Manual
11

Important Assembly Notes
1) While assembling unit, take time before and after each phase to make sure fort is level. If fort is not level, assembly will be difficult and
improper assembly may result. Extra care must be taken to ensure the fort is square.
2) Tighten bolts securely, tighten nuts on bolts flush to the tube or member.
3) Pay close attention to the ITEMS NEEDED FOR EACH PHASE. They can be a valuable aid when sorting your wood and hardware. Assembly
will be made easier if items are sorted by phase.
4) Pay close attention to make sure you are using the correct hardware in the correct phases. Using incorrect hardware may result in improper
assembly.
5) Whenever a T-nut is used, follow these directions. Place T-nut in pre-drilled hole. Tap in with hammer. Place bolt with washers in the opposite
side. Hand tighten to make sure the bolt is in the T-nut. DO NOT over tighten.
6) Read the steps of each phase thoroughly. The written steps may include important information not shown in the illustrations.
Basic Setup Dimensions
Place the set on level ground, not less than 6' - 7" [2 m] from any structure or obstruction such
as a fence, garage, house, overhanging branches, laundry lines, or electrical wires.
Safe Play Zone
Safe play height: 14.5' [4.4 m]
Maximum fall height: 6.36' [1.9 m]
General Information:
Your set has been designed and
engineered for children only and
for residential use only.
A maximum of 150 lbs. per child
is recommended for play
activities designed for individual
use.
A maximum of 120 lbs. per child
is recommended for play
activities designed for multiple
child use.
A maximum of 6 children is
recommended for this swing set.
«
S
P
A
N
I
S
H
28.01 ft
[8.5 m]
20.52 ft [6.3 m]
6.58 ft [2 m]
7.36 ft [2.2 m]
14.85 ft
[4.5 m]
6.58 ft
[2 m]
2.09 ft
[.6 m]
8.05 ft
[2.5 m]
7.82 ft [2.4 m]
6.36 ft [1.9 m]
12

(Level 24")
(Open End Wrenches 1/2"
& 7/16")
(Square)
(Tape Measure)
(3/8" Drive Ratchet, 1/2" STD
Sockets 1/2" Deep Sockets)
(Claw Hammer)
(Cordless Drill or
Electric Drill)
(Drill Attachments: Phillips
Head & Socket Driver)
(An Adult w/ an
Adult Helper)
(Rubber Mallet - Optional)
(Ladder)
(Phillips Screw Driver)
(1/8", 3/16", 7/16" & 3/8"
Drill Bits)
Tools Required for Installation:
(These are the tools that are generally required for assembly of our outdoor products.
These tools are not included with the outdoor product purchase.)
13

Parts Identification
Wood Components
(NOT TO SCALE)
E2 - FRONT LOWER LEFT FORT LEG - W4L06277
1 3/8"x3 3/8"x42 7/8" (36x86x1090)
(1)
E3 - FRONT UPPER RIGHT FORT LEG - W4L06280
1 3/8"x3 3/8"x46" (36x86x1168)
(1)
E4 - FRONT LOWER RIGHT FORT LEG - W4L06381
1 3/8"x3 3/8"x42 7/8" (36x86x1090)
(1)
E5 - FORT LEG - W4L15011
1 3/8" x 3 3/8" x 46" (36 x 86 x 1168)
(1)
E6 - REAR LOWER LEFT FORT LEG - W4L06382
1 3/8"x3 3/8"x42 7/8" (36x86x1090)
(1)
E7 - FORT LEG - W4L15015
1 3/8" x 3 3/8" x 46" (36 x 86 x 1168)
(1)
E8 - REAR LOWER RIGHT FORT LEG - W4L06380
1 3/8"x3 3/8"x42 7/8" (36x86x1090)
(1)
E9 - UPPER ANGLE BRACE BOARD - W4L06301
1 3/8"x3 3/8"x34 1/8" (36x86x866)
(2)
E10 - LOWER ANGLE BRACE BOARD - W4L06303
1 3/8"x3 3/8"x46" (36x86x1168)
(2)
H1 - UNIVERSAL GROUND BOARD - W4L06276
1"x3 3/8"x42" (24x86x1066)
(4)
H2 - FLOOR RAIL - W4L12103
1"x3 3/8"x46" (24x86x1168)
(1)
H3 - FLOOR RAIL - W4L12104
1"x3 3/8"x46" (24x86x1168)
(1)
G1 - END SUPPORT - W4L07240-A
1"x5 1/4"x42 7/8" (24x134x1090)
(1)
H4 - ANGLE BRACE - W4L06561
1"x3 3/8"x14" (24x86x355)
(4)
F1 - TARP SUPPORT - W4L15014
1 3/8"x2"x13 1/4" (36x50x335)
(1)
14

Parts Identification
Wood Components
(NOT TO SCALE)
J1 - SAFETY BOARD - W4L06295
1"x2 3/8"x31 5/8" (24x60x802)
(2)
K1 - ROCKWALL BOARD - W4L04792
5/8"x5 1/4"x23 1/4" (16x134x590)
(1)
K2 - ROCK BOARD - W4L15016
5/8" x 5 1/4" x 23 1/4" (16 x 134 x 590)
(4)
L1 - TOP RAIL - W4L15012
5/8" x 4 3/8" x 44 7/8" (16 x 112 x 1140)
(2)
M2 - FLOOR BOARD - W4L06287
5/8"x3 3/8"x16 3/8" (16x86x416)
(2)
M4 - TARP BOARD - W4L15013
5/8" x 3 3/8" x 24 1/2" (16 x 86 x 622)
(2)
M3 - GROUND BOARD - W4L04794
5/8"x3 3/8"x23 1/4" (16x86x590)
(2)
M77 - SLIDE BRACE - W4L04711
5/8"x3 3/8"x14 1/4" (16x86x362)
(1)
M78 - CENTER SLIDE BRACE - W4L04712
5/8"x3 3/8"x14 1/4" (16x86x362)
(2)
N1 - WALL RAIL - W4L06288
5/8"x2 3/8"x39 7/8" (16x60x1012)
(1)
N2 - WALL RAIL - W4L06289
5/8"x2 3/8"x29 5/8" (16x60x754)
(1)
N4 - WALL BOARD - W4L06296
5/8"x2 3/8"x14 5/8" (16x60x372)
(4)
N5 - WALL BOARD - W4L06297
5/8"x2 3/8"x14 5/8" (16x60x372)
(2)
M5 - BOARD - W4L11800
5/8"x3 3/8"x24 1/8" (16x86x612)
(1)
H5 - UPRIGHT BRACE - W4L13751
1"x3 3/8"x6 3/4" (24x86x170)
(4)
N3 - TARP SUPPORT - W4L15018
5/8"x2 3/8"x23 1/4" (16x60x590)
(1)
15

Parts Identification
Wood Components
(NOT TO SCALE)
P1 - LADDER RUNG - W4L06283
1 3/8"x1 3/8"x23 1/4" (36x36x590)
(3)
P2 - TARP SUPPORT - W4L15017
1 3/8"x1 3/8"x20 1/4" (36x36x514)
(1)
Q1 - SWING BEAM GROUND BOARD - W4L06304
1"x4 3/8"x45 5/8" (24x112x1160)
(2)
SB1 - SWING BEAM - W4L06298
5 1/4"x2"x46" (134x50x1168)
(1)
W2 - SWING BEAM SUPPORT - W4L06300
2"x3 3/8"x46" (50x86x1168)
(1)
W1 - SWINGBEAM SUPPORT - W4L15010
2"x3 3/8"x42 3/8" (50x86x1075)
(1)
1) E1 - FRONT UPPER LEFT FORT LEG - W2A02876
1 3/8"x3 3/8"x46" (36x86x1168)
2) FP1 - FLOOR PANEL - W2A01901
1 1/4"x19 7/8"x16 7/8" (32x504x430)
SB2 - SWING BEAM - W4L06299
5 1/4"x2"x46" (134x50x1168)
(1)
N6 - FLOOR BOARD - W4L06286
5/8"x2"x16 1/2" (16x50x418)
(1)
16

Parts Identification
Hardware
- BOLT WH 5/16x1/2 - H100115
(28)
- BOLT WH 5/16x1 3/4 - H100011
(6)
- BOLT WH 5/16x2 - H100012
(9)
- BOLT WH 5/16x2 1/2 - H100014
(2)
- BOLT WH 5/16x3 - H100016
(11)
- BOLT WH 5/16x4 - H100020
(9)
- BOLT WH 5/16x4-1/4 - H100166
(22)
- BOLT WH 5/16x4 1/2 - H100021
(1)
- NUT BARREL WH 5/16x7/8 - H100005
(52)
- NUT BARREL WH 5/16x1 1/2 - H100006
(4)
- NUT BARREL WH 5/16x1 3/4 - H100007
(2)
- LAG SCREW WH 5/16x2 - H100027
(9)
- BOLT HEX 5/16x2-3/4 - H100047
(4)
- BOLT WH 1/4x1-1/2 - H100143
(4)
- NUT BARREL WH 1/4x7/8 - H100140
(4)
- T-30 TORX WRENCH - H100114
(2)
- T-40 TORX BIT - A100042
(2) - T-30 TORX BIT - H100147
(2)
- T-40 TORX WRENCH - A100041
(2)
- BOLT WH 5/16x1 - H100008
(12)
- LAG SCREW WH 1/4x2 - H100146
(4)
17

Parts Identification
Hardware
- SCREW PFH 8x1-1/8" - H100088
(13)
- SCREW PFH 8x1-1/2" - H100086
(90)
- SCREW PFH 8x2 1/2 - H100090
(48)
- SCREW PWH 8x5/8 - H100128
(12)
- BOLT PTH 1/4x3/4 - H100063
(9)
- NUT LOCK 5/16 - H100110
(11)
- T-NUT 1/4 - H100072
(20)
- T-NUT 5/16 - H100074
(37)
- 9 1/2" SWING HANGER QUICK LINK - H100099
(6)
- WASHER LOCK EXT 8x19 - H100030
(64)
- WASHER LOCK EXT 12x19 - H100031
(40)
- WASHER SAFETY 17x30 - H100103
(4)
- WASHER FLAT 8x27 - H100105
(15)
- WASHER LOCK INT 8x15 - H100108
(9)
- WASHER LOCK EXT 6x15 - H100138
(9)
- BOLT WH 1/4x1-3/4 - H101027
(4)
- WASHER LOCK EXT 8x15 - H100139
(7)
- NUT BARREL WH 1/4x5/8 - H100136
(7)
- BOLT WH 1/4x1/2 - H100141
(4)
- BOLT WH 1/4x1-1/4 - H100142
(2)
- BOLT WH 1/4x5/8 - H100490
(7)
18

Parts Identification
Accessories
(NOT TO SCALE)
-SWINGBEAMJOINTBRACKETBLUE-A4M00696
(1)
-SWINGBEAMEXT.BRACKETBLUE-LEFT-A4M00511
(1)
-SWINGBEAMEXTBRACKETBLUE-RIGHT-A4M00512
(1)
-SWINGBEAMSINGLECLAMPBLUE-A4M01000
(2)
- MOLDED SWING SEAT - BLUE/BLUE
461c-c - A6P00329
(2)
- "A" REVISION TAG - A100314
(1)
- BLUE HC ROCK #1 - A6P00041
(2) - BLUE HC ROCK #2 - A6P00040
(2)
-METALDECKBRACE380C/CBLUE-A4M00999
(4)
- 90° L-BRACKET - BLK - A4M00555
(6)
- PICKET PAL - A6P00410
(1)
19

Parts Identification
Accessories
(NOT TO SCALE)
-SLIDERAILTOPLEFT-A6P00176
(1)
-SLIDERAILBOTTOMLEFT-A6P00177
(1)
-SLIDERAILBOTTOMRIGHT-A6P00179
(1)
-SLIDERAILTOPRIGHT-A6P00178
(1)
- SLIDE BED 8' BLUE - A6P00358
(1)
- METAL TRAPEZE BLUE - A4M00697
(1)
- TARP .4x580x1736 - A6P00328
(1)
- GROUND STAKE REBAR - A4M00527
(6)
- METAL L-BRACKET - BLUE - A4M00938
(2)
EA-HANDGRIPBLUEPLASTIC-A6P00314
(2)
20