Backyard Discovery 9198074 Use and care manual

Made in China | INS-9198074-A-TUBE SLIDE-RH-ENG 3-27-19
For the most up to date assembly manual,
to register your set, or to order replacement parts please visit
www.backyarddiscovery.com
SAVE THIS ASSEMBLY MANUAL FOR FUTURE REFERENCE IN THE EVENT THAT
YOU NEED TO ORDER REPLACEMENT PARTS.
Model # 9198074
TUBE SLIDE
Owner’s Manual & Assembly Instructions
MANUFACTURED BY:
Backyard Discovery
3305 Airport Drive
Pittsburg, KS 66762
800-856-4445
average 2 person assembly time
assembly time may vary based on skill level
Right Exit Slide

Owner's Manual
Tools Required for Installation

Place the set on level ground, not less than 6 ft 7 in [2 m] from any structure or obstruction such as a
fence, garage, house, overhanging branches, laundry lines, or electrical wires.
• While assembling unit, take time before and after each phase to make sure fort is level. If fort is not level, assembly will be difficult and
improper assembly may result. Extra care must be taken to insure the fort is square.
• The safe play area refers to a zone extending 6 ft (2m) beyond the play product on all sides, including the space above the play product.
Owner's Manual
Basic Setup Dimensions & Assembly Notes
3'-6"
[1 m]
7'-1"
[2 m]
4'-8"
[1 m]
4'-4"
[1 m]

UPRIGHT - W4L12970
1 3/8"x3 3/8"x19 7/8" (36x86x505)
E85
(x1)
UPRIGHT - W4L12971
1 3/8"x3 3/8"x24 1/2" (36x86x623)
E86
(x1)
GROUND BOARD - W4L12969
1 3/8"x3 3/8"x14 3/8" (36x86x366)
E87
(x1)
BOLT WH BLK
5/16x2-3/4
(x4)
H100195
BOLT WH BLK
5/16x1 1/2
(x4)
H100407
BOLT WH BLK
1/4x1 1/2
(x2)
H100406
WASHER LOCK EXT BLK
8x19
(x4)
H100198
WASHER FLAT BLK
9x18
(x2)
H100474
T-NUT BLK
5/16
(x9)
H100379
NUT LOCK WZ
1/4
(x115)
H100148
BOLT PTH WZ
1/4x3/4
(x115)
H100769
BOLT PTH WZ
1/4x7/8
(x2)
H100795
NUT BARREL WH BLK
1/4x5/8
(x2)
H100404
WASHER LOCK EXT BLK
8x15
(x2)
H100400
Hardware Components
Owner's Manual
arts Identification
Wood Components (Not to Scale)

TORX WRENCH
T-40
(x2)
A100041
PHILLIPS WRENCH
#2
(x2)
H100776
TORX WRENCH
T-30
(x2)
H100114
TORX BIT
T-30
(x2)
H100147 TORX BIT
T-40
(x2)
A100042
Hardware Components
arts Identification
Owner's Manual

SLIDE ENTRANCE LEFT
(x1)
A6P00302-2 SLIDE ENTRANCE RIGHT
(x1)
A6P00302-1
SLIDE ELBOW
(x9)
A6P00302-4
EXIT TOP
(x1)
A6P00302-5R
EXIT SUPPORT
(x1)
A6P00302-6R
Accessory Components (Not to Scale)
Owner's Manual
arts Identification

METAL GROUND STAKE BROWN
(x2)
A100178
TUBE SLIDE BRACKET
(x36)
A4M00996
Accessory Components (Not to Scale)
Owner's Manual
arts Identification
TUBE SLIDE BRACKET - RH
(x1)
A4M01087

Phase 1
STE 1
SLIDE ENTRANCE LEFT
(x1)
A6P00302-2 SLIDE ENTRANCE RIGHT
(x1)
A6P00302-1
BOLT PTH WZ
1/4x3/4
(x8)
H100769
NUT LOCK WZ
1/4
(x8)
H100148
769 (x8)
BOLT - 3/4"
302-1 (x1)
SLIDE ENTRANCE RIGHT
302-2 (x1)
SLIDE ENTRANCE LEFT
TI :
LAYING THE PARTS ON THEIR FLAT
END MAKES ASSEMBLY EASIER.
148 (x8)
NUT - 1/4"

STE 2
Phase 1
SLIDE ELBOW
(x8)
A6P00302-4
BOLT PTH WZ
1/4x3/4
(x32)
H100769
NUT LOCK WZ
1/4
(x32)
H100148
NOTE:
REPEAT THIS STEP (3) MORE TIMES.
302-4 (x2)
SLIDE ELBOW
148 (x8)
NUT - 1/4"
769 (x8)
BOLT - 3/4"

148 (x8)
NUT - 1/4"
769 (x8)
BOLT - 3/4"
302-4 (x1)
SLIDE ELBOW
302-5L (x1)
EXIT TO
BOLT PTH WZ
1/4x3/4
(x8)
H100769
NUT LOCK WZ
1/4
(x8)
H100148
EXIT TOP
(x1)
A6P00302-5RSLIDE ELBOW
(x1)
A6P00302-4
Phase 1
STE 4

STE 4
Phase 1
BACK VIEW
SLIDE INTO GROOVE
ON EXIT SUPPORT.
TI :
• RECOMMENDED BOLT ASSEMBLY ORDER,
CLOCKWISE FROM TOP RIGHT.
• MAKE SURE THE 'ARROW' ON THE EXIT SUPPORT IS
ALIGNED WITH THE 'R' ON THE SLIDE ELBOW.
• USE A SCREW DRIVER TO ALIGN HOLES.
• WHEN REMOVING SPACER, BEGIN ALIGNMENT OF
TUBE SLIDE OPENING FOR EASIER ASSEMBLY.
EXIT SUPPORT
(x1)
A6P00302-6R
BOLT PTH WZ
1/4x3/4
(x7)
H100769 NUT LOCK WZ
1/4
(x5)
H100148
FRONT VIEW
TUBE SLIDE SPACER
START ALIGNMENT
OF HOLES FROM
THE TOP LEFT.
FACTORY INSTALLED
NUT. (BOTH CORNERS)
148 (x5)
NUT - 1/4"
769 (x7)
BOLT - 3/4"
302-6R (x1)
EXIT SU ORT

Phase 2
REFERENCE
IMPORTANT: BRACKET CONFIGURATION ASSEMBLY & PLACEMENT.
2 HOLES
3 HOLES
1 HOLE
CONFIGURATION 'A' DIAGRAM CONFIGURATION 'B' DIAGRAM
CONFIGURATION 'A'
CONFIGURATION 'B'
NOTE ALIGNMENT MARKINGS
PAY CLOSE ATTENTION TO THE ALIGNMENT MARKINGS ON
EACH SLIDE SECTION. THE MARKINGS WILL AID YOU IN
POSITIONING THE METAL SLIDE BRACKETS CORRECTLY.
NOTE:

Phase 2
STE 1
LEFT SIDE VIEW
BOLT PTH WZ
1/4x3/4
(x12)
H100769
NUT LOCK WZ
1/4
(x12)
H100148
TUBE SLIDE BRACKET
(x6)
A4M00996
(1)-ENTRANCE SUB-ASSEMBLY (1)-STRAIGHT TUBE SUB-ASSEMBLY
TOP VIEW
NOTE:
ENTRANCE SUB-ASSEMBLY
"L" TO LEFT OF SEAM
996 (x6)
TUBE SLIDE BRACKET
ELBOW TUBE
SUB-ASSEMBLY
148 (x12)
NUT - 1/4"
769 (x12)
BOLT - 3/4"
• USE A SCREW DRIVER TO ALIGN HOLES.
TI :
•ALIGN THE 'L' ONE HOLE TO THE LEFT OF SEAM TO ACHIEVE THE
PROPER POSITION WHEN ASSEMBLING THE SLIDE.
• NOTE THIS SECTION ASSEMBLY USES CONFIGURATION 'A' SHOWN
IN THE REFERENCE PAGE.

Phase 2
STE 2
TUBE SLIDE BRACKET
(x6)
A4M00996
BOLT PTH WZ
1/4x3/4
(x12)
H100769
NUT LOCK WZ
1/4
(x12)
H100148
• ALIGN THE 'R' AND THE 'ARROW' TO ACHIEVE THE
PROPER POSITION WHEN ASSEMBLING THE SLIDE.
• NOTE THIS SECTION ASSEMBLY USES CONFIGURATION
'B' SHOWN IN THE REFERENCE PAGE.
NOTE:
148 (x12)
NUT - 1/4"
ELBOW TUBE SUB-ASSEMBLY
(1)-ELBOW TUBE SUB-ASSEMBLY
996 (x6)
TUBE SLIDE BRACKET
NOTE THE "R" AND "ARROW"
MARKINGS TO AID IN
POSITIONING THE METAL
BRACKETS.
769 (x12)
BOLT - 3/4"

Phase 2
STE 3
TUBE SLIDE BRACKET
(x6)
A4M00996
BOLT PTH WZ
1/4x3/4
(x12)
H100769
NUT LOCK WZ
1/4
(x12)
H100148
• ALIGN THE 'R' AND THE 'ARROW' TO ACHIEVE THE
PROPER POSITION WHEN ASSEMBLING THE SLIDE.
• NOTE THIS SECTION ASSEMBLY USES CONFIGURATION
'B' SHOWN IN THE REFERENCE PAGE.
(1)-ELBOW TUBE SUB-ASSEMBLY
NOTE:NOTE:
ELBOW TUBE SUB-ASSEMBLY
NOTE THE "R" AND "ARROW"
MARKINGS TO AID IN
POSITIONING THE METAL
BRACKETS.
769 (x12)
BOLT - 3/4"
148 (x12)
NUT - 1/4"
996 (x6)
TUBE SLIDE BRACKET

Phase 2
STE 4
TUBE SLIDE BRACKET
(x6)
A4M00996
BOLT PTH WZ
1/4x3/4
(x9)
H100769
NUT LOCK WZ
1/4
(x12)
H100148
(1)-ELBOW TUBE SUB-ASSEMBLY
BOLT PTH WZ
1/4x7/8
(x3)
H100795
996 (x6)
TUBE SLIDE BRACKET
NOTE THE "R" AND "ARROW"
MARKINGS TO AID IN
POSITIONING THE METAL
BRACKETS.
ELBOW TUBE SUB-ASSEMBLY
769 (x10)
BOLT - 3/4"
795 (x2)
BOLT - 7/8"
148 (x12)
NUT - 1/4"
• ALIGN THE 'R' AND THE 'ARROW' TO ACHIEVE THE
PROPER POSITION WHEN ASSEMBLING THE SLIDE.
• NOTE THIS SECTION ASSEMBLY USES CONFIGURATION
'B' SHOWN IN THE REFERENCE PAGE.
• NOTE THE (3) BOLTS USED TO ASSEMBLE THE SLIDE
BRACKET ARE 7/8", NOT 3/4".
NOTE:
001 (x1)
TUBE SLIDE BRACKET - RH
TUBE SLIDE BRACKET - RH
(x1)
A4M01087

Phase 2
STE 5
TUBE SLIDE BRACKET
(x6)
A4M00996
BOLT PTH WZ
1/4x3/4
(x12)
H100769
NUT LOCK WZ
1/4
(x12)
H100148
(1)-EXIT SUB-ASSEMBLY
NOTE THE "R" AND "ARROW"
MARKINGS TO AID IN
POSITIONING THE METAL
BRACKETS.
EXIT SUB-ASSEMBLY
• ALIGN THE 'R' AND THE 'ARROW' TO ACHIEVE THE
PROPER POSITION WHEN ASSEMBLING THE SLIDE.
• NOTE THIS SECTION ASSEMBLY USES CONFIGURATION
'B' SHOWN IN THE REFERENCE PAGE.
NOTE:
148 (x12)
NUT - 1/4"
769 (x12)
BOLT - 3/4"
996 (x6)
TUBE SLIDE BRACKET

Phase 3
STE 1
E86 (x1)
U RIGHT
E85 (x1)
U RIGHT
E87 (x1)
GROUND BOARD
195 (x4)
BOLT - 2-3/4
198 (x4)
WASHER - 8x19
379 (x4)
T-NUT - 5/16"
UPRIGHT - W4L12970
1 3/8"x3 3/8"x19 7/8" (36x86x505)
E85
(x1)
GROUND BOARD - W4L12969
1 3/8"x3 3/8"x14 3/8" (36x86x366)
E87
(x1)
UPRIGHT - W4L12971
1 3/8"x3 3/8"x24 1/2" (36x86x623)
E86
(x1)
T-NUT BLK
5/16
(x4)
H100379
BOLT WH BLK
5/16x2-3/4
(x4)
H100195
WASHER LOCK EXT BLK
8x19
(x4)
H100198
NOTE:
HAMMER T-NUTS INTO PROVIDED
HOLES IN 'E87'.

Phase 3
STE 2
379 (x4)
T-NUT - 5/16"
407 (x4)
BOLT - 1 1/2"
BOLT WH BLK
5/16x1 1/2
(x4)
H100407
T-NUT BLK
5/16
(x4)
H100379
(1)-TUBE SLIDE SUB-ASSEMBLY (1)-SLIDE BRACE SUB-ASSEMBLY
HAMMER T-NUTS INTO PROVIDED
HOLES IN 'E85' AND 'E86'.
NOTE:

Phase 3
STE 3
404 (x2)
NUT BARREL - 5/8"
400 (x2)
WASHER - 8x15
406 (x2)
BOLT - 1 1/2"
474 (x2)
WASHER - 9x18
178 (x2)
METAL GROUND STAKE BROWN
WASHER LOCK EXT BLK
8x15
(x2)
H100400
WASHER FLAT BLK
9x18
(x2)
H100474 NUT BARREL WH BLK
1/4x5/8
(x2)
H100404
BOLT WH BLK
1/4x1 1/2
(x2)
H100406
METAL GROUND STAKE BROWN
(x2)
A100178