BakerStone Original Series User manual

Original Series
Outdoor Multi-function
Cooking Center
Product Guide
Model # BSO4500-EBK-OOO-000
Important, Retain for Future Reference: Read Carefully
WARNING: This product guide contains important information
necessary for the proper assembly and safe use of the appliance.
Read and follow all warnings and instructions before assembling
and using the appliance.
Follow all leak-check procedures in the Product Guide before
using the appliance.
This appliance is for outdoor use only.
If you smell gas:
Extinguish any open flame.
Open lid.
If odor continues, keep away from the appliance and
immediately call your gas supplier or your fire department.
Do not store or use gasoline or other flammable liquids or
vapors in the vicinity of this or any other appliance.
An LP cylinder not connected for use shall not be stored in the
vicinity of this or any other appliance.
Failure to follow these instructions could result in fire or explosion
which could cause property damage, personal injury or death.
DANGER
WARNING
www.bakerstonebox.com - (855) 657 OVEN (6836)

WARNINGS
Failure to follow these instructions could result in fire or explosion which could cause
property damage, personal injury or death.
The installation must conform with local codes or, in the absence of local
codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural
Gas and Propane Installation Code, CSA B149.1, or the Propane Storage and Handling
Code,CSA B149.2, or the Standard for Recreational Vehicles, ANSI A119.2/NFPA 1192, and
CSA Z240 RV Series, Recreational Vehicle Code, as applicable.
This appliance shall be used only outdoors, and shall not be used inside a building,
garage or any other enclosed area.
This appliance is not intended to be used in or on a recreational vehicle or boat.
While using this appliance maintain a minimum clearance from sides and back of at
least 36in (0.9m) between appliance and any combustible material or contruction. Do
not use this appliance under overhead combustible suaces.
Clean and inspect the supply hose and regulator before each use of the appliance.
If there is evidence of abrasion, wear, cuts, or leaks, the hose must be replaced prior
to using the appliance. Only the included hose or a replacement supplied by the
manufacturer shall be used with the appliance.
The appliance is only to be fueled by a LP (liquid propane) gas cylinder measuring 12”
(30.5cm) diameter and 18” (45.7cm) high with a 20lb. (9.1kg) capacity. The gas cylinder
(tank) must incorperate a Type 1 cylinder valve and an over filling protection device
(OPD).
The LP gas cylinder must be constructed and marked in accordance with the
Specifications for LP gas Cylinders of the U.S. Department of Transportation (D.O.T.) or
the Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods
and Commission, CAN/CSA-B339, as applicable.
Do not unhook or replace the LP Gas Cylinder while the appliance is in use.
Before each use and aer replacing the LP gas cylinder peorm a leak check at all
connections and fittings. Do not use an open flame to check for leaks.
Keep the fuel supply hose away from any heated suace(s).
This appliance is not intended for commercial use.
The use of alcohol, prescription or non-prescription drugs may impair the consumer’s
ability to properly assemble or safely operate the appliance.
In the event of an oil or grease fire do not attempt to extinguish with water. Immediately
call the fire department. A Type BC or ABC fire extinguisher may, in some circumstances
contain and/or extinguish the fire.
Do not leave the appliance unattended. Keep children and pets away from the
appliance at all times.
Do not move the appliance when in use.

WARNINGS - continued
This appliance is not intended for and should never be used as a heater.
This appliance will be hot during and aer use. Use insulated oven mitts or gloves for
protection from hot suaces or splatter from cooking liquids.
Do not touch the appliance until it has completely cooled. The black metal housing
can reach temperatures of 400°F(204°C) during use.
Use only appropriate bake-ware or utensils while baking and cleaning the appliance.
Do not use plastic, silicone or glass.
Do not allow food other than Pizza or Bread Dough to contact the stones. Any foods
that contain fat, oil or butter (meats, items coated with olive oil, cookies, biscuits, etc.)
should not contact the stones directly. These items should be baked in a metal baking
pan, on a metal baking sheet or in a cast-iron skillet as the stones will absorb the fat, oil
and butter which can cause smoking, odors, staining, and can impart rancid flavors to
items that you bake in the future.
Stones are fragile and can break if dropped. The appliance becomes extremely hot, do
not touch the stones or any other part of the appliance while it is in use.
To clean stones, heat the appliance for 15 minutes aer food is cooked and scrape o
any remaining residue. Do not use any cleaning agents or other liquids to clean the
stones.
Do not place gasoline, alcohol, wood products, charcoal or any other combustible
material (unless BakerStone approved) in the baking chamber.
Remove any appliance cover and place at least 10 feet (3 Meters) from appliance
before use.
Do not alter or change the gas valve orifices.
This appliace requires regular cleaning of major components and more detailed
cleaning of burner system aer prolonged period of storage. Insects and/or insect
nests may prevent safe usage and proper peormance of the appliance
Only use the presure regulator and hose included with this appliance.
Do not alter or install as a built in appliance.
The use of alcohol, prescription, or non-prescription drugs may impair the consumer’s
ability to properly assemble or safely operate the appliance.
Chant HK Development Limited
Suite 706, Rightful Centre, 11-12 Tak Hing Street, Jordan, Kowloon, Hong Kong

Product Assembly Diagram
Figure 1.2
Figure1.1
Figure 1.3

What’s in the package
Assembly of the Grill
LP Gas Cylinder Requirements
LP Gas Cylinder Placement
LP Gas Cylinder Connection
LP Gas Leak Test
Pre-Use Safety Checks
Lighting Instructions
How to Use The Pizza Oven Box
Routine Care & Cleaning
Periodic Care & Cleaning of Burner System
Customer Service
Customer Service Parts Identifier
Warranty
Frequently Asked Questions
4
6
14
15
16
17
17
18
20
22
24
25
26
28
30
Table of Contents Page
Gridddle Seasonning Instructions 19
Cleaning Your Griddle 23

4
What’s in the package
Before assembly, ensure that all parts below are included. Please note part numbers are not listed
in numerical order. For a complete parts diagram and part list for customer service needs such as
replacement parts please go to page 26.
18 - Cabinet
Base Panel
21 - Cabinet
Middle Panel
25 - Cabinet
Front Panel
Firebox Assembly
47 - Pizza Oven Box
43 - Griddle 46- Griddle Cover Assembly
46.1 - Griddle Cover
46.2 - Griddle Cover Handle
15 - Wheel Axle
16 - Wheel
(x2)
17 - Wheel
Cap (x2)
50 - Match Lighter
20 - Side Frame
Right
19 - Caster
(x2)
13 - Griddle Storage Rack24 - Cabinet Top Panel1 12 - Front Brace
14

5
Tools required for assembly, not included:
Have a question? Please Do Not Return This Product To The Store.
Contact us first! 1-855-657-6836
or email [e-mail]
11 - Drip Tray
Support
(x2)
29 - Rear Beam 23- Firebox Support
(x2)
22 - Gas Cylinder
Hook
10 - Folding Table
(x2)
28 - Table
Support Right
(x2)
32 - Griddle
Grease Cup
30 - Grill
Grease Cup
26- Drip Tray
6 - Control Knob
(x6)
Battery
48 - Warming Rack49 - Cooking Grate
(x3)
2 - Flame
Tamer (x4)
AA - M4x12 Pan
Head Screw
(x5)
CC - M5x12 Pan
Head Screw
(x4)
DD - M6x12 Pan
Head Screw
(x40. )
EE - M6x12 Flat
Head Screw
(x12)
FF - M5 Nut
(x4) GG - M10 Nut (x2) HH - M5 Spring Washer
(x4)
II - Battery
BB - M5x8mm
Shoulder
Screw(x1)
27

6
1418 20
DD
Assembly of the Grill
STEP 1. Attach the CASTERS (19) to the RIGHT SIDE
FRAME (20).
STEP 2. Attach the WHEEL (16), WHEEL AXLE (15) to the LEFT
SIDE FRAME (14) using NUTS (GG). Next place the CAPS (17)
onto the wheels.
STEP 3. Assemble the CABINET BASE PANEL (18) to the SIDE
FRAMES (14 and 20) using SCREWS (DD).
19
DD
20
14
16
GG
15
17

7
STEP 4.Attach the CABINET FRONT PANEL (25) to the BASE
PANEL (18) and SIDE FRAME (20) using 4 SCREWS (DD).
STEP 5.Attach the CABINET MIDDLE PANEL (21) to the BASE
PANEL (18) and CABINET FRONT PANEL (25) using 3 SCREWS
(DD).
STEP 6. Attach the STORAGE RACK (13) to the CABINET TOP
PANEL (24) using 4 SCREWS (CC), 4 SPRING WASHERS (HH)
and 4 NUTS (FF).
DD 21
CC
FF
HH
24
13
25
DD

8
STEP 7. Pre-install 2 CREWS(DD) on the SIDE FRAME(14)
and CABINET MIDDLE PANEL(21) respectively. First
attached the CABINET TOP PANEL(24) into the CABINET
MIDDLE PANEL(21), then attached the CABINET TOP
PANEL(24) into the SIDE FRAME(14). Then fasten the 4
pre-install screws.
STEP 8.Attach the FRONT BRACE (12) to the SIDE FRAMES
(14 and 20), FRONT CABINET PANEL (25) and CABINET
MIDDLE PANEL (21) using 1 SCREW (AA) and 6 SCREWS (DD)
as shown.
STEP 9. Attach the REAR BEAM (29) using 4 SCREWS (DD).
DD
DD
DD
29
AA DD
12
14
21
24

9
STEP 10. Attach the FIREBOX SUPPORTS (23) using 4 SCREWS
(DD) to the SIDE FRAMES (14 and 20).
STEP 11. Attached the DRIP TRAY SUPPORTS (11) using 4
SCREWS (AA).
STEP 12.With 2 or more people lift the FIREBOX
ASSEMBLY and place onto the assembled cart.
DD
23
23
11
11
AA

10
STEP 13. Attach the FIREBOX ASSEMBLY to the assembled
cart using 4 SCREWS (DD) on each side.
STEP 14.Secure the HOSE CLIP (34.3) using 1 SCREW (DD).
DD
34.3
DD
STEP 15.Attached the GAS CYLINDER HOOK (22).
22

11
STEP 16. Attach MATCH LIGHTER chain (50) to CABINET
MIDDLE PANEL (21) using 1 SCREW (BB).
STEP 17. Attach the TABLE SUPPORT LEFT (27) and RIGHT
(28) to each side of the grill using 12 SCREWS (EE). NOTE:
Ensure the arrows on the parts are facing upwards.
STEP 18.Hang the FOLDING TABLES (10) onto the TABLE
SUPPORTS.
EE
27
28
10
10
BB 50

12
STEP 20. Install the BATTERY (II) by unthreading the ignitor
button and inserting the BATTERY (II) with the positive (+)
sign facing out.
STEP 21. Insert the GRIDDLE GREASE CUP (32) into
the front side of the grill assembly.
STEP 19. Attached the CONTROL KNOBS (6) by firmly
pushing them onto the GAS VALVES.
6
32
I I
STEP 22.Loosen the pre-assembled SCREWS from the
HANDLE (46.2) and then attach the HANDLE (46.2) to the
GRIDDLE COVER (46.1) using the SCREWS.
Place the GRIDDLE COVER (46) on top of the firebox when
the GRIDDLE (43) or PIZZA OVEN BOX (47) is not in use.
When using the GRIDDLE (43) or PIZZA OVEN BOX (47) hang
the GRIDDLE COVER (46) on the hook behind the firebox.
46
46.2 46.1

13
STEP 23. Insert the DRIP TRAY (26) and GRILL GREASE CUP
(30) into the back side of the grill as shown.
STEP 24. Put the FLAME TAMER (2), COOKING GRATE (49)
and WARMING RACK (48) into the MAIN FIREBOX in
order.
26
30
49
2
48

14
LP Gas Cylinder (tank) Requirements
The appliance is only to be fueled by an LP (liquid propane) gas cylinder measuring 12” (30.5cm)
diameter and 18” (45.7cm) high with a 20lb. (9.1kg) capacity. The gas cylinder (tank) must
incorperate a Type 1 cylinder valve and an over filling protection device (OPD).
The LP gas cylinder must be constructed and marked in accordance with the Specifications for
LP gas Cylinders of the U.S. Department of Transportation (D.O.T.) or the Standard for Cylinders,
Spheres and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA-B339, as
applicable.
Place dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of
dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps
or plugs may result in leakage of propane.
The gas cylinder must have:
- A shuto valve terminating in a Type 1 gas cylinder valve outlet.
- A Type 1 valve that prevents gas flow until a positive seal is obtained.
- An arrangement for vapor withdrawl. The gas cylinder must be kept in the upright position at all
times.
- A collar to protect the shut-o valve.
- A safety relief device that has direct communication with the vapor space of the gas cylinder.
- A listed over filling prevention device (OPD).
This appliance is not intended to be used with natural gas.
Appliance Installation Requirements
This appliance must be installed in accordance to the following codes:
- National Fuel Gas Code ANSI Z223.1 NFPA 54
- Natural Gas and Propane Installation Code: CAN/CGA B149.1
- Propane Installation Code: CAN/CGA B149.2 (Canada)
LP Gas Cylinder (tank) Filling Requirements:
- LP gas cylinder should only be filled by a qualified licensed LP gas dealer.
- New LP gas cylinders must be purged prior to filling.
- DO NOT allow the cylinder to be filled beyond 80% capacity. Over-filled LP gas cylinders can
create a dangerous condition. Over-filled LP gas cylinders can build-up pressure and cause the
relief valve to expel propane gas vapors. The vapor is combustible and if it comes in contact with
a spark source or flame an explosion causing severe burns, bodily harm, or death could occur.
- Always use a protective cylinder cap when grill is not connected to the gas cylinder.
- Inspect the LP gas cylinder valve rubber seal for cracks, wear or deterioration prior to use. A
damaged rubber seal can cause a gas leak, possibly resulting in an explosion, fire or severe
bodily harm.
Spare LP Gas Cylinder
- Do not store a spare LP gas cylinder under or near the appliance.

15
LP Gas Cylinder Placement
Place the LP Gas Cylinder into the Base and secure with the
GAS CYLINDER HOOK (28) by ensuring it inteaces with the top
rim of the LP Gas Cylinder.
WARNING:
The pressure regulator and hose assembly supplied with the appliance must be used.
Replacement pressure regulators and hose assemblies shall be those specified by the
appliance manufacturer.
Storage of this appliance indoors is permissible only if the cylinder is disconnected and
removed from the appliance.
Cylinders must be stored outdoors out of the reach of children and shall not be stored in a
building, garage, or any other enclosed area.
Only use this appliance outdoors in a well ventilated area.
Never operate this appliance within 36in (0.9m) of any structure, combustible material or other
gas cylinder.
Do not use this appliance under overhead combustable construction.
Do not place or use this appliance on a combustable surface.
This appliance becomes hot, do not place on any surface which cannot withstand high
temperatures without deforming or being damaged.
This appliance is not to be installed in or on boats or recreational vehicles.
Failure to follow these instructions could result in fire, explosion or burn hazard which could
cause propey damage, personal injury or death.

16
LP gas cylinder connection:
Step 1. Ensure the LP cylinder used conforms to the
requirements listed on the previous page. Also inspect the
LP gas cylinder valve rubber seal for deterioration such as
cracks, deformation or tears.
Step 2. Inspect the LP gas cylinder valve to ensure the
threads match that of the included hose and regulator.
Step 3. Ensure all the burner control knobs are in the OFF
position [see Figure - 1].
Step 4. Thread the included hose and regulator onto the
LP gas cylinder. Turn the coupling fastener clockwise by
hand until it stops [see Figure - 2]. WARNING: Do not use
tools to tighten the coupling fastener.
LP Gas Cylinder
Hose and Regulator
Coupling fastener
Figure - 2
Hose and regulator
attachment
Figure - 1

17
LP Gas Leak Test
Before first use and aer each time the LP gas cylinder
is reconnected or changed the LP gas Leak Test must be
performed.
Do not use an open flame to check for leaks.
Do not smoke or be in the presence of any ignition
sources while performing a leak test.
Perform leak test outdoors in a well ventilated area.
Step 1 Prepare a soapy water solution of water and
detergent.
Step 2 Aer connecting the appliance to the LP gas
cylinder, slowly open the valve completely.
Step 3 Listen for any hissing sounds. WARNING: If hissing
sounds are present turn o the gas valve and contact a
licensed gas repair specialist.
Step 4 Spray a mild soapy water solution on all gas
connections. Inspect all connections for the growing
presense of bubbles [see Figure - 3]. These bubbles
represent a leak. If a leak is present tighten the fitting
and test again with the soapy water solution. WARNING:
If bubbles remain present turn o the gas valve and
contact a licensed gas repair specialist.
Pre-Use Safety Check
Before first use and aer each time the LP gas cylinder
is reconnected or changed the LP gas Leak Test must be
performed.
Check all components for proper assembly and function.
Place the appliance outdoors on a secure, stable, non-
combustible, and level surface.
Ensure this appliance is at least 36 inches (0.9 m) from any
structure, combustible material or other gas cylinder [see
Figure - 4].
Ensure all surfaces including firebox and grease tray are
clean prior to each use of the Pizza Oven Box.
WARNING: Failure to follow these instructions could
result in fire, explosion or burn hazard which could cause
propey damage, personal injury or death.
Figure - 3
Figure - 4
36"
36"

LIGHTING INSTRUCTIONS
Read all instructions before lighting.
For the grill, open lid during lighting.
STEP 1 Check that the control knobs are in the (OFF)
position.
STEP 2
Turn on the gas tank valve.
STEP 3 Push and turn one of the burners to (HIGH) [see
Figure - 4] while pressing and holding the (IGNITION)
button [See Figure - 5].
STEP 4 Once burner lights release the (IGNITION) button.
STEP 5 Repeat procedure for other burners.
STEP 6 WARNING: If the ignition does not light within 5
seconds, turn the burners to (OFF) and wait 5 minutes
for any gas to dissipate. Repeat prior steps or light using
a match.
STEP 7
between and .
MATCH LIGHTING
If the appliance does not light using the steps above a
match may be used to light the appliance.
STEP 1
before you turn on the gas tank valve.
STEP 2 Attach a match to the lighting rod and light the
match.
STEP 3 Insert the match through the side of the firebox
towards the burner [see Figure - 6] or from the top
through the cooking grates and immediately turn one of
the burners to (HIGH).
STEP 4 Burner should light immediately. If the burner does
and wait 5 minutes before trying again.
HOW TO TURN OFF APPLIANCE:
STEP 1 Rotate all burners to the (OFF) position
[see Figure - 7].
STEP 2
Figure - 5
Figure - 6
Figure - 4
Figure - 7
Turn o LP supply at cylinder when appliance is not
in use.
18