BALAY 3VS950IA User manual

Dishwasher Summary instructions
Brief and handy: everything
your dishwasher needs ...
Before using for the first
time, read the operating
instructions!
Switch off the appliance Everythingo.k ...
9000 294 516    
en
Start programme Here we go ...
Adding rinse aid
Adding detergent
Select programme
Filling the salt dispenser
Switching on the appliance
Adjusting the water softening system * Quickly sorted ...
Water
hardness
value _dH
Hardness
range mmol/l Set value
soft
soft
medium
medium
medium
hard
hard
hard
How to adjust the water softening system
–Switch on ON/OFF switch
–Hold down programme button A and press START button until H:0...
is indicated on the digital display.
–Release both buttons.
The LED for button A flashes and the factory set value of H:04 is
indicated on the digital display
–Press programme button C.
Each time the button is pressed the set value increases by one setting;
when the value reaches H:07, the display jumps back to H:00 (off).
–Press START button. The chosen setting has now been stored.
Ask your water supply
company what the
water hardness is and
enter...
*only before the
first wash or if the
water hardness
has been
changed
A B C
Dissolves limescale (not necessary for set value 0!) ...
Unscrew
cover. Fill the salt
dispenser with
water before the
first wash only.
Add salt
(never add
detergent!).
Screw on the
cover. Wash
immediately.
Spick and span ... Refill if rinse-aid refill indicator is lit!
Press mark 1,
lift up cover 2. Adding rinse aid.Screw on the cover.
CLICK!
A lot of dirt, a lot of detergent ...
If required, open
the cover (press
button).
Attention
Combination
products are not
suitable for all
programmes, follow
manufacturer’s
instructions.
Adding
detergent.Slide cover shut, press.
PLOP!
Quick, economical or intensive ...
The max. possible number of programmes is illustrated
in this overview. The corresponding programmes for your
appliance can be found on the fascia.
Overview of programmes
The programme data has been measured in the laboratory
according to European standard EN 50242.
Deviations are possible in practice.
*half normal load
1:40-2:15
1,30-1,60
–
11-15
2:20
1,05
9
–
1:05-1:20
0,70-0,85
–
10-15
0:29*
0,80
10
–
0:15
0,05
4
–
1:25-2:30
1,00-1,60
–
9-19
Quick
45_
Eco
50_
Auto
45_/65_
Duration: hs/mins
Energy Consumption: kWh
Water consumption in litres
With Aquasensor
Auto
65_/75_
Auto
35_/45_
Prerinse
Additional options ** Flexibility...
Express Wash
(VarioSpeed)
... is obtained by
increased energy
consumption at a
constant cleaning and
drying performance.
Half load
... for a few items, saves
water, energy and time
** depending on model
IntensiveZone
... perfect for a mixed
load. Washing pressure
and washing
temperature are
increased slightly.
Hygiene
... The temperature is
increased during
the rinsing process. This
increases the hygiene
status.
Extra drying
... improves the drying
result by increased
temperature in the final
rinse (Please take care
with delicate dishes)

Maintenance and care For perfect rinsing results ... Cleaning waste water pump
Filters ...
check, if
required clean
Rotate filter
cylinder, remove
filter system ...
rinse under
running water ... insert ... Screw on filter system NOTE
MARK!
–Pull out the mains plug
–Remove filters and scoop out water
–Lever off cover (––>A)
–Check area around the fan impeller
for foreign objects
–Click cover shut (––>B)
–Insert filters
Spray arms ...
Remove
blockages/deposits
pull lower arm
upwards ... unscrew upper arm ... clean spray nozzles under running water
(if required use
toothpicks) ...
insert lower arm ...
screw on upper arm
tightly
A B
Rectifying minor faults yourself ... ... as it is worth doing it yourself!
Fault Possible causes
Display “ ” display is lit Supply fitting jammed or calcified Open supply fitting.
Remedial action
Display “E:25”
and “ ” is lit Waste water pump blocked Clean waste-water pump (see above).
Rust on the cutlery Cutlery not rust-resistant. Hard knife blades are more susceptible Never wash rusting parts
in the appliance.
Other fault display “E:XX”
is lit
Display “E:24”
and “ ” is lit
Residual water
in the appliance
Appliance has technical defect
Waste water hose is blocked
or kinked
Unplug appliance.
Install waste water hose without kinks.
The programme has not yet
ended Close and switch on the appliance or terminate the programme
(see Terminating the programme).
Cover not attached to waste
water pump
Install supply hose without kinks.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 10 l/min. when
water supply is open. If the flow rate
is less, replace the supply fitting.
Attach cover (see above).
Call factory customer service
(state fault display).
Extraneous rust
Use dishwasher-proof cutlery.
Fault Possible causes Remedial action
Stains and streaks
Milky deposits on the
utensils (can be removed)
Rinse-aid dosage too high/too low
Glasses not dishwasher-proof.
Streaks: reduce dosage.
Use dishwasher-proof glasses.
Use a detergent suitable for glasses.
More information can be found in the operating instructions
Milky deposits, glasses
cloudy/tarnished
(cannot be removed)
Correctly set water softening system.
Utensils are not clean
Spray arms blocked
Clean the filters (see above).
Plastic/utensils discoloured
Too little detergent. Follow manufacturer’s instructions
(detergent).
Sand or gritty residue on the
utensils
Utensils are situated close together or
one above the other
Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Separate the utensils, prevent contact
points.
Follow manufacturer’s instructions
(detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Water softening system incorrectly set;
No salt
Water or limescale stains: increase
dosage.
Refill with salt.
Discoloration caused by food colourings
(tomato sauce) Discoloration is harmless; subsequent
rinse cycles will cause it to fade.
Terminating the programme ... Loading the dishwasher correctly ...
Whilethe programme is running,
press the START button for
approx. 3 sec. (Reset).
The numerical display
indicates “0:01” Switching off the appliance
approx. 1 minute after
the programme ends,
0:00 is indicated
Dishwasher-proof utensils (not soiled with ash, wax, lubricating grease, ink or adhesive labels; remove
large remnants of jam, milk products and food according to the operating instructions and check that the
spray arms can rotate freely.