BALAY 3VF330NP User manual

Brief Instructions: Dishwasher
Short and handy: everything
your dishwasher needs...
Before using for the first
time, read the Installation
and Operating Instructions!
Switch appliance ON,off we go...
Press main switch, choose programme.
Close door.
Signal sounds, open door. End-of-programme
indicator flashes, press main switch.
Switch appliance OFF,everything OK...
Add rinse-aid.
Add detergent.
Select programme.
Add salt.
9000 196 625   
en Setting the water softening system * Quickly sorted
Find out the water
hardness at your water
utility company and
enter below
* only before using the
dishwasher for the first
time or if the water hard-
ness changes
Read off the setting
Setting°dH °fH °Clarke mmol/l
and then select a setting
– Hold down programme button Band switch on the main
switch, then release the buttons. The . display flashes and
buttons Aand Billuminate (water hardness setting was set
to 2 at the factory).
– Each time button Bis depressed, the setting increases by
one (0-3). If buttons A, Band Cilluminate, the maximum
water hardness setting has been reached. If the water
hardness setting is now increased again, the lights go out
and the water hardness setting is set to 0.
– Switch off the main switch. The selected setting has been
stored in the appliance.
0
1
2
3
Reset
A B C
22–35
0–6
7–16
17–21
0–1,1
1,2–2,9
3,0–3,7
3,8–6,2
9–20
0–11
12–29
30–37
38–60
0–8
21–26
27–44
Dissolves limescale (not required for set value 0!)
Unscrew
the lid. Only before using
the dishwasher
for the first time
pour approx. 1 l /
1 1/4 pt water into
the salt opening.
Pour in max.
1.5 kg / 3 lb 5 oz
salt (never deter-
gent!)
Screw on the
lid. Switch on
dishwasher
immediately.
Everything is sparkling clean ... Refill whenever level indicator is light!
Press mark 1,
lift up lid 2. Pour in rinse aid.Close the lid. CLICK!
Very dirty dishes, a lot of detergent ...
If required, open
the lid (press the
pin).
Warning,
combination
products are not
suitable for all
programmes,
follow manufac-
turer’s instructions.
Pour in
detergent.Push the lid shut, press.
PLOP!
Quick, economical or intensive ...
This overview indicates the max. possible number of
programmes. The programmes which correspond to your
appliance can be found on your appliance fascia.
The programme data are values measured in the
laboratory in compliance with Standard EN 50242.
Deviations is practice are possible.
Overview of programmes
120
2,00
21
140
1,05
17
70
1,00
17
30
0,80
13
15
0,10
5
35_50_70_65_40_
Duration in minutes
Power consumption in kWh
Water consumption in litres
Intensive Normal Eco Gentle Quick Prerinse
110
1,75
21
Additional programmes ** Increasedflexibility ...
** on some models
Extra dry
... improves the drying
result by increased
temperature in the final
rinse (Please take care
with delicate dishes)
Upper basket cleaning
...Only the crockery in the
upper basket is cleaned
Half load
... for a few items, saves
water, energy and time

Maintenance and care For perfect rinsing results Waste water pump *
Filters
Check and,
if required,
clean:
Rotate filter cylinder,
remove filter system
Rinse under
running water
Insert
Screw on filter
system.
NOTE MARK!
*some models
– Set main switch to OFF
– Scoop out any water
– Remove the filters
– Remove the cover (⇒A)
– Check the inner compartment for foreign
objects and, if required, remove foreign
objects
– Re-insert the cover (⇒B)
– Re-insert the filters and screw into position
– Re-insert the cover (⇒B)
– Re-insert the filters and screw into position
Spray arms
Remove blockages/
deposits
Pull up lower arm
Clean under running
water (if required,
use a toothpick)
Insert lower arm
Screw on upper arm
deposits
Unscrew upper arm
A
B
Rectifying minor faults yourself ... ... as it is worth doing it yourself!
Fault Possible causes
Appliance is not running /
stops
Check water supply
Display lights up
Supply fitting not open
Supply hose kinked
Supply fitting jammed or calcified
Open supply fitting.
Install supply hose without kinks.
1. Unscrew water connection.
2. Clean filter in the water connection.
3. Flow rate must be min. 9 l/min.
when water supply is open.
If the flow rate is less, replace
the supply fitting.
Remedial action
Plastic / utensils
discoloured Too little detergent
Discoloration caused by food colourings
(tomato sauce)
Follow manufacturer’s instructions
(detergent).
Discoloration is harmless; subsequent
rinse cycles will cause it to fade.
Residual water in the
appliance Waste water pump blocked
The programme
has not yet ended
Clean waste-water pump (see above).
Close the appliance, switch on and
wait until the programme ends
(“end of programme” display lights up)
or terminate programme
(see Terminating the programme).
Fault Possible causes Remedial action
Stains and streaks
Milky film on the utensils
(removable)
Rust on the cutlery
Rinse-aid dosage too high / too low
Glasses not dishwasher-proof.
Cutlery not rust-resistant
Hard knife blades are more susceptible
Extraneous rust
Streaks: reduce dosage.
Water or limescale stains: increase
dosage.
Use dishwasher-proof glasses.
Use a detergent suitable for glasses.
Use dishwasher-proof cutlery.
Never wash rusting parts
in the appliance.
More information can be found in the operating instructions
Milky film, glasses cloudy /
dull
(not removable)
Water softening system incorrectly set;
No salt Correctly set water softening system. Refill with salt.
Utensils are not clean
Sand or gritty residue
on the utensils
Utensils are situated close together
or one above the other
Too little detergent
Unsuitable programme selected
Spray arm nozzles blocked
Filters dirty, not seated firmly
Spray arms blocked
Separate the utensils, prevent contact
points.
Follow manufacturer’s instructions
(detergent).
Select a more intensive programme.
Clean the spray arms (see above).
Clean the filters (see above).
Arrange the utensils so that the spray
arms can rotate freely.
Interrupting the programme ... Terminating the programme ... Arranging dishes correctly ...
–Open the door.
– Press the two RESET
buttons simultaneously
(approx. 3 seconds)
(RESET).
– Close the door.
– Open the door.
– Press the START/STOP
button.
– To continue, press the
START/STOP button again.
– Close the door.
Switch off the
appliance.
After 1 minute the
programme ends.
The ”signal
sounds and the
standby indicator
illuminates”.
Arrange dishwasher-proof dishes in accordance with the operating manual
(without residual ash, wax, lubricating grease, ink, sticky labels; remove any
large remnants of jam, milk products or food) and check that the spray arms
can rotate freely.