Ballard Designs Ceylon Bakers Rack MD10 User manual

PRODUCT NAME: Ceylon Bakers Rack
ITEM NUMBER: MD100
DIMENSIONS OF ITEM ASSEMBLED: 70 3/8”H x 36”W X 18”D
UPDATED: 9/16/2013
PRODUCTS ARE NOT INTENDED
FOR COMMERCIAL USE.
Page 1 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
MADE IN VIETNAM

Customer Service: 800-367-2810
Online: www.ballarddesigns.com Page 2 of 6
TOOLS NEEDED:
-Screwdriver needed.
-Assembly requires 2 or more people.
NOTE:
Unpack and assemble the Bakers Rack on a
smooth, clean surface to avoid scratching and
losing parts.
Bottom Middle Shelf (J) and Cabinet Back (N)
have dowels and do not screw in.
Ltr.
A 14 60mm Allen Screws
B 4
70mm Allen Screws
C 4
90mm Allen Screws
D 1 Allen Wrench
Top Bar
Top Shelf
Top
Middle Shelf
Bottom Shelf
Left Door
Right Door
Cabinet Back
Cabinet Bottom
Right Side
Left Side
Legs
E 14 Caps
F 2 Anti Tip Kits
Qty. Hardware Included
Ltr.
G
I
1
1
Bottom
Middle Shelf
J 1
H 1
K 1
L 1
M 1
N 1
O 1
P 1
Q 1
R 4
Qty. Components

Page 3 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 1:Lay the Left Side (Q) on a smooth, clean surface. Then loosely attach the Top Shelf (H) and
Top Bar (G) with the 60 mm Allen Screws (A) using the Allen Wrench (D).
STEP 2:Lay the STEP 1 assembly on its back and attach the Top Middle Shelf (I), and the
Bottom Shelf (K) with 60 mm Allen Screws (A) using the Allen Wrench (D). Attach the
Bottom Middle Shelf (J) and the Cabinet Back (N) by inserting the Dowels into the holes
on in the Left Side (Q).
(Q)
(Q)
(N)
(J)
(K)
(N)
(H)
(L)(J)
(D)
(D)
(G) (H)(E)(C)(A)
(A)
(A)
(O)
(I)
(M)
(G)
(K)(I)(F)(D)(B)

Page 4 of 6
STEP 3:Flip the assembly back on the Left Side (Q) and align the Right Side (P) with all the
Shelves (G-K, N). Screw in the remaining 60mm Allen Screws (A) to the Right Side (P) and
Shelves (G-I, K). Fully tighten all the 60mm Allen Screws securing the Left Side (Q) and
Right Side (P).
STEP 5:Attach the Cabinet Bottom (O) to the assembly made in STEP 3 by laying the Rack on it’s
back and tightening the 90mm Allen Screws (C) using the Allen Wrench (D).
STEP 4:Attach Legs (R) to the Cabinet Bottom (O) with the 70mm Allen Screws (B) using the
Allen Wrench (D).
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
(B)
(R)
(O) (D)
(C)
(O)
(W) (X)(V)(U)(S)(P) (Q)
(P)
(D)
(D)
(A)
(T)(R)

(E)
(E)
(Q)
(P)
Page 5 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
STEP 7: Insert the Caps (E) into the screw holes on both the Right (P) and Left (Q) Sides of the Rack.
Clean & Care:
Please refer to the care instructions on the hang tag.
Levelers: If doors are not even, adjust levelers until doors become even.
STEP 6:Attach the Left (L) and Right (M) Doors to the Rack by sliding the female hinge on each Door
onto the male receiving part of the hinge on the Right (P) and Left (Q) Sides. Be sure the
door catches are aligned when the Doors are closed.
NOTE: If the doors are uneven, adjust the levelers on the bottom of each Leg (R) by twisting
them clockwise or counterclockwise until the doors are even.
(M)
(L)
(Q)
(P)
(R)
Levelers

(T)
(S)
(U)
(S)
(V)
Page 6 of 6
Customer Service: 800-367-2810
Online: www.ballarddesigns.com
ANTI TIP INSTALLATION: PART F
Attach the Wall Brackets (S) to the wall using 1 50mm Screws (T) for
each Bracket and Wall Plug (U). Use the Retention Belts (V) to connect the Wall Brackets (S)
to the Brackets on the back of the Top Shelf (H).
Wall
Wall
Ltr.
S
T
V
2 50mm Screws
U
2 Wall Brackets
2 Retention Belts
2 Wall Plugs
Qty. Hardware Included