B&M Boltzero Bunk Bed User manual

Boltzero Bunk Bed
Assembly Instructions - Please keep for future reference
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
Issue 1 - 31/07/15
Dimensions
Width - 2010mm
Depth - 990mm
Height - 1630mm
428/3256

1
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product, this
could cause damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Unit weight: 41kgs.
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Warnings
• READ CAREFULLY - RETAIN
FOR FUTURE REFERENCE
• WARNING: High beds and
upper bed of bunk beds are not
suitable for children under six
years due to the risk of injury
from falls.
• WARNING: Bunk beds and
high beds can present a serious
risk of injury from strangulation if
not used correctly. Never attach
or hang items to any part of the
bunk bed that are not designed
to be used with the bed, for
example, but not limited to
ropes, strings, cords, hooks,
belts and bags.
• WARNING: Children can
become trapped between the
bed and the wall, a roof pitch,
the ceiling, adjoining pieces of
furniture (e.g. cupboards) and
the like. To avoid risk of serious
injury the distance between the
top safety barrier and the
adjoining structure shall not
exceed 75mm or shall be more
than 230mm.
• WARNING: Do not use the
bunk bed/high bed if any
structural part is broken or
missing.
• Always follow the
manufacturer’s instructions.
• The recommended size of the
mattress is L1900 x W900mm.
• Ventilation of the room is
necessary in order to keep the
humidity low and to prevent
mould in and around the bed.
• Assembly instructions
including a list of the parts
supplied and details of any tools
required to assemble the bed
are included in the pack.
• The maximum thickness of the
mattress is 190mm. Mattress
maximum thickness marking on
the product are found on the
post.
• Check regularly that all
assembly fastenings are
properly tightened.
• THIS BED COMPLIES WITH
EN747-1:2012+EN747-2:2012
Manufacturer: BL Packaging Co.
Ltd.

2
Components - Parts
Please check you have all the parts listed below
Back Left End Post
1Front Left/Back Right End Post2Front Right End Post3
Upper Side Rail x 2
4Lower Side Rail x 25
Lower Front Rail
6
Lower Back Rail
7Ladder8
If you have damaged or missing components, call the
Customer Helpline: Argos = 0345 640 0800
sticker (1) sticker (2) sticker (3)
Arrow up

3
Components - Fittings
Please check you have all the fittings listed below
Tools required
Footing x 4
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
A
Long Cap x 16
B
Short Cap x 11
C
Washer x 4
D
Rubber Mallet (Not Provided)
Components - Parts (cont.)
Please check you have all the parts listed below
Upper Front Safety Rail9
Upper Back Safety Rail
10 Slat x 1211
Short Stiap x 1
E
Metal Slats Pusher x 1
F

4
Assembly Instructions
Step 1
Step 2
Attaching footings
Attach footings to end
posts , and as
shown.
Attaching lower side
rails
With the help of an
assistant holding the end
posts, attach the lower
side rails to the end
posts as shown. Insert
into holes on the end
posts first then push
down the siderails to
lock.
5
1
1 2 3
3
2
9
2
A
A
A
A
A
A
1
5
5
5
5
3
2
2
2
2

5
Assembly Instructions
Step 3
Step 4
Attaching upper side
rails
Attach the upper side
rails (4) to the end posts
as shown. Insert into
holes on the end posts
first then push down the
rails to lock.
Attaching lower rails
Attach the lower front rail
(6) and lower back rail (7)
to the end posts (1) and
(2) as shown. Insert into
holes on the end posts
first then push down the
rails to lock.
1
3
2
2
4
4
4
holes
1
1
6
6
6
7
7
2
2

6
Assembly Instructions
Step 5
Step 6
Attaching right hand
end panel
Attach the lower front rail
(6) and lower back rail (7)
to the other end posts (2)
and (3) as shown. Insert
into holes on the end
posts first then push
down the rails to lock.
Attaching upper back
safety rail
Attach the upper back
safety rail to the end
posts (1) and (2) as
shown. Insert into holes
on the end posts first
then push down the rails
to lock.
3
3
2
2
6
6
7
7
2
2
1
110
10

7
Assembly Instructions
Step 7
Step 8
6
6
8
8
2
3
3
8
8
9
9
9
D
D
D
D
D
D
Attaching ladder
Attach the ladder (8) into
holes on washers and
the lower front rail (6) as
shown.
Note: Make sure
to position the
ladder with the
arrow sticker on
the ladder
pointing up.
6
8
D
Attaching upper front
safety rail
Position the upper front
safety rail (9) and hold to
align and insert the
ladder (8) and washers
into holes as shown.
Before fully inserting the
ladder, insert the upper
front safety rails into
holes on the end posts
(2) and (3). Then push
down the rails to lock.
2 3
8
9
D
Arrow up

8
Assembly Instructions
Step 9
Step 10
Attaching upper slats
Note: Before
attaching the
slats ,
carefully make
adjustments to
ensure the bed
frame is straight.
Note: Position
the horizontal rail
below when
attaching the
slats onto the
bed.
Starting on one end,
attach the slats one
by one into upper rails
(9) and (10). Push to
insert the button on the
slats into the hole on the
rails as shown. Make
sure it is lock when you
hear the ‘click’ sound.
Insert one end of the
slats first before inserting
and locking the other
end.
Attaching lower slats
Repeat step 9 to attach
the other slats into
holes on lower rails (6)
and (7).
11
11
x6
Insert button
to hole to lock
Cross rail
position bottom
11
11
11
10
10
9
x6
11
11
7
7
6
6

9
Assembly Instructions
Step 11
Attaching caps
Attach long caps and
short caps into holes
on the end posts as
shown. Insert and lock it
carefully into holes by
using a rubber mallet.
C
C
C
B
B
B
9
9
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 640 0800
C
C
C
C
C
C
BB
BB
B B
B
B
B
B
B
BB
B
CCC
C
C
BB
9
10
4
4
5
5
6
7
This unit must be fixed to
a wall.
Move the bunk bed into
position on the wall.
Position the short strap
to the top post of upper
back safety rail to
mark fixing holes on the
wall. Remove the wall
strap then drill holes and
insert appropriate wall
plugs. Reposition short
strap and fix using
appropriate screws.
Warning:
Before drilling,
check wall for
hidden pipes and
cables. Consult a
qualified
specialist if
unsure.
Assembly is complete.
Fixing to wall
E
E
10
Step 12
Wall
Wall
E
E
10
10

A Guide to - Wall Mounting & Fixings
Revision 2 - 7/10/09
Important note:
Types of walls
Care &
Maintenance
No.1 “General Purpose” wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
No.3 “Cavity Fixing” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
Generally aerated blocks should not
be used to support heavy loads, use
a specialist ftting in this case. For light
loads, general purpose wall plugs can
be used.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
For use with plasterboard partitions or
hollow wooden doors.
For use when ftting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with walls stuck with
plasterboard. The hammer fxing allows
it to be fxed to the wall rather than the
plasterboard. Always check the fxing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
Safety: Always check the ftting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the ftting to ensure the wall plugs
or screws do not become loose.
You can use one of the following types of wall plug if your walls are made
of brick, breeze block, concrete, stone or wood.
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well ftted and are a tight ft in the
drilled hole.
If plastic wall plugs
are supplied with your
product:
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualifed
tradesperson if you are unsure.
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fxings is the
responsibility of the installer.

Use the metal slats pusher to remove the slats as shown in the diagram. Insert it into the
front/back/safety rails then pull it until the slats is detached.
11
11
10
9
6
7
F
10
11
F
10
11
Guide to Disassembling the Slats
Metal Slats Pusher (Provided)
Please keep this tool for future use.
Tools required