Banks Outdoors FEEDBANK 40 User manual

INSTRUCTION MANUAL

WARRANTY
LIMITED LIFETIME WARRANTY
The Banks Outdoors product(s) purchased from our authorized dealers is
warranted to be free from defects in material and workmanship for as long as
the registered original owner owns the product. Banks Outdoors will repair
or replace your product, with the same or comparable model free of charge
(shipping charges not included) for life, once the product has been registered
with Banks Outdoors, in the event of a defect in materials or workmanship
occurring during normal use. The warranty only extends to the original retail
purchaser named on the product registration. The product must be
registered on www.banksoutdoors.com or by mail with the card
included in the product box before warranty performance.
WHAT IS NOT COVERED?
Not covered under this warranty are failures due to misuse, abuse or normal
wear and tear and improper installation. Additionally, failures due to acts
of God & nature, such as storms, strong winds, and animal damage are not
covered by this warranty.
NO ADDITIONAL WARRANTY APPLIES
The Limited Lifetime Warranty is the exclusive warranty for Banks Outdoors
products. Dealers, Retailers, or Representatives are not authorized to alter this
warranty or create additional warranties on behalf of Banks Outdoors.
HOW TO SUBMIT A WARRANTY REQUEST
Please call 1-800-262-4129.
To become a registered owner of your Banks Outdoors Wild Water or
Feedbank, please complete the online Product Registration form at
www.banksoutdoors.com, or submit your registration by mailing the card
included with your product. Your product needs to be registered in order to
take advantage of the Limited Lifetime Warranty.
2 BANKS OUTDOORS

WWW.BANKSOUTDOORS.COM 3
FEEDBANK & WILD WATER® OVERVIEW
CONGRATULATIONS ON PURCHASING YOUR NEW BANKS PRODUCT!
Implementing a solid feeding program has never been easier
with Banks Outdoors’ gravity-fed Feedbank deer feeders.
The single post design of this feeder allows big bucks to feed
unhampered and unharmed by legs getting in the way. These
feeders also permit you to set up multiple deer feeding sites
by installing different posts around your property for easy
location changes.
Wild Water® is the watering system for all the wildlife on
your property. Reduce the effect disease and dehydration
have on your deer herd. Fill the Wild Water® concealed tank
and let it flow into the trough. Once it is filled to capacity,
the system will shut itself off until water is needed again.
Water multiple animals at one time.
If during the assembly you have any questions, please call:
800-262-4129 from 8am-5pm M-F central standard time.

FEEDBANK 40
4 BANKS OUTDOORS
1. Unpack the Feedbank from the box.
2. Place the cover on the feeder so that the name reads forward.
3. Take your steel strap and bolt it to the back of the feeder with
(2) 1/4-20” bolts and (2) lock washers.
4. To install the feeder port, first take a t-style thumb bolt and slide a
lock washer on and then a fender washer. Take the t-style thumb bolt
with washers and slide the bolt from the inside of the port out. Match
up to the treaded insert at the bottom of the body of the feeder and
screw the bolt to it, attaching the feed port. Do the same thing to the
second bolt for that feed port. Repeat this for all ports.
INCLUDED PARTS:
(1) Feeder
(1) Camo Strap
(2) 1/4-20” Bolts
(4) Fender Washers
(1) Steel Strap
(2) Feed Ports
(6) 1/4” Lock Washers
(4) T-Style Thumb Bolts
(1) Cover

FEEDBANK 40
WWW.BANKSOUTDOORS.COM 5
5. Attach camo strap around the steel strap and attach the Feedbank to
your desired post or tree.
6. Feedbank 40 can attach to a tree, fence post or t-post.
7. Fill with feed. All feed ports slide in and out when t-style thumb bolt
is loosened, to control flow. Set flow according to type of feed you are
using.
8. Your Feedbank is ready to go!

FEEDBANK 150
6 BANKS OUTDOORS
1. Unpack the Feedbank from the box. You should have 6 main parts.
2. To attach cover, place it on top of the feeder so the locking tabs are
above the (2) latches on each side. Latch over the top of the tabs to
secure the cover.
3. To attach the Feed Port, first take (1) of the 1/4-20x1” Bolts and slide
on the Internal Star Lock Washer. From the inside of the feeder, press
through the bolt and washer into the attachment hole. Take a Feed
Port and also connect to this 1” Bolt that is sticking through the bottom
of the feeder. From the inside of the feed port, place the fender washer
on the 1” Bolt. Then, place the 1/4-20” Lock Washer onto the bolt. To
fasten all together, place the 1/4-20” Wing Nut on the bolt and tighten
to a snug fit. Repeat this step for each attachment hole on the feeder.
INCLUDED PARTS:
(1) Feeder
(4) Feed Ports
(1) Cover
(8) 1/4-20” Lock Washers
(8) 1/4-20 x 1” Bolts
(8) 1/4” Fender Washers
(8) 1/4-20” Wing Nuts
(8) 1/4-20” Internal Star
Lock Washers

FEEDBANK 150
WWW.BANKSOUTDOORS.COM 7
4. After the cover and Feed Ports are installed, you need to purchase an
8’ 4x4 green-treated post. Dig into the ground 4’ and backfill the post so
it is level.
5. Slide Feedbank over the post.
6. Another option is to cut off a tree and slide it over a trunk of the
stree - just be sure to cut it off level, leaving 4’ above the ground.
7. Fill with feed. All feed ports slide in and out, when bolts are loosened
to control flow. Set flow according to type of feed you are using.
8. Your Feedbank is ready to go!

FEEDBANK 300
8 BANKS OUTDOORS
1. Unpack the Feedbank from the box. You should have 6 main parts.
2. To attach cover, place it on top of the feeder so the locking tabs are
above the (2) latches on each side. Latch over the top of the tabs to
secure the cover.
3. To install the feeder port, first take a t-style thumb bolt and slide a
lock washer on and then a fender washer. Take the t-style thumb bolt
with washers and slide the bolt from the inside of the port out. Match
up to the treaded insert at the bottom of the body of the feeder and
screw the bolt to it, attaching the feed port. Do the same thing to the
second bolt for that feed port. Repeat this for all ports.
INCLUDED PARTS:
(1) Feeder
(4) Feed Ports
(8) T-Style Thumb Bolts
(1) Cover
(8) 1” Fender Washer
(8) 1/4” Lock Washers

FEEDBANK 300
WWW.BANKSOUTDOORS.COM 9
4. After the cover and Feeder Ports are installed, you need to purchase
an 8’ 4x4 green-treated post. Dig into the ground 3’ and backfill the
post so it is level.
5. Slide Feedbank over the post.
6. Another option is to cut off a tree and slide it over a trunk of the
stree - just be sure to cut it off level.
7. Fill with feed. All feed ports slide in and out, when t-style thumb bolt
is loosened to control flow. Set flow according to type of feed you are
using.
8. Your Feedbank is ready to go!

FEEDBANK 600
10 BANKS OUTDOORS
1. Unpack the Feedbank from the box. You should have 6 main parts.
2. To attach cover, place it on top of the feeder so the locking tabs are
above the (2) latches on each side. Latch over the top of the tabs to
secure the cover.
3. To install the feeder port, first take a t-style thumb bolt and slide a
lock washer on and then a fender washer. Take the t-style thumb bolt
with washers and slide the bolt from the inside of the port out. Match
up to the treaded insert at the bottom of the body of the feeder and
screw the bolt to it, attaching the feed port. Do the same thing to the
second bolt for that feed port. Repeat this for all ports.
INCLUDED PARTS:
(1) Feeder
(4) Feed Ports
(8) T-Style Thumb Bolts
(1) Cover
(8) 1” Fender Washers
(8) 1/4” Lock Washers

WWW.BANKSOUTDOORS.COM 11
FEEDBANK 600
4. After the cover and Feeder Ports are installed, you need to purchase
an 8’ 6x6 green-treated post. Dig into the ground 3’ and backfill the
post so it is level.
5. Slide Feedbank over the post.
6. Another option is to cut off a tree and slide it over a trunk of the
stree - just be sure to cut it off level.
7. Fill with feed. All feed ports slide in and out, when t-style thumb bolt
is loosened to control flow. Set flow according to type of feed you are
using.
8. Your Feedbank is ready to go!

12 BANKS OUTDOORS
WILD WATER® 100
1. Set your trough on level ground.
2. Set your tank on level ground over the top of the trough.
3. Install the float valve to the outlet hole on the Wild Water tank.
4. Fill the tank through the 2” hole.
5. After the tank is full, insert the 2” plug into the fill hole.
6. Allow water to fill into the trough until it automatically shuts itself
off. Water should not overflow the trough. If water does proceed over
the top of the trough, verfiy that the trough is level.
7. Install the float valve protection cover with the (4) 1 3/4” bolts.
INCLUDED PARTS:
(1) Trough
(1) 2” Plug
(1) Float Valve Protection Cover
(1) Flot Valve
(1) 100 Gallon Tank
(1) 1 1/4” Plug
(4) 1 3/4” Cover Bolts

WWW.BANKSOUTDOORS.COM 13
WILD WATER® 300
1. Set your troughs on level ground.
2. Set your tank on level ground over the top of the troughs.
3. Install the 2 float valves to the outlet holes on the Wild Water tank.
4. Fill the tank through the 2” hole.
5. After the tank is full, insert the 2” plug into the fill hole.
6. Allow water to fill into the trough until it automatically shuts itself
off. Water should not overflow the troughs. If water does proceed over
the top of the troughs, verfiy that the troughs are level.
7. Install the 2 float valve protection covers with the (8) 1 3/4” bolts.
INCLUDED PARTS:
(2) 3’ Trough (s)
(1) 2” Plug
(2) Float Valve Protection Covers
(1) 300 Gallon Tank
(2) Float Valves
(8) 1 3/4” Cover Bolts

14 BANKS OUTDOORS
WILD WATER® FILL TANK
1. Attach hose and shut-off valve to the outlet hole on your Wild
Water.
2. Make sure valve is in shut-off position and fill your 100 gallon tank.
3. Remove plug on top of the Wild Water and insert hose into the
opening.
4. Open valve and fill Wild Water.
INCLUDED PARTS:
(1) 100 Gallon Tank
(1) Shut-off Valve
(1) 6’ Hose
(1) 2” Plug

WILD WATER® BLADDER
WWW.BANKSOUTDOORS.COM 15
1. Attach hose and shut-off valve to the outlet hole on the Bladder.
2. Make sure valve is in shut-off position and fill Bladder.
3. Remove plug on top of the Wild Water and insert hose into the
opening.
4. Open valve and fill Wild Water.
INCLUDED PARTS:
(1) Bladder
(1) Shut-off Valve
(1) Hose
(1) Screw-on Cover

COMPANY INFORMATION 2020
WWW.BANKSOUTDOORS.COM
31785 64TH AVE CANNON FALLS, MN 55009
1-800-262-4129