kollectaball Hopper User manual

Kollectaball Hopper Assembly InstructionsKollectaball Hopper Assembly Instructions
Thank-you for purchasing a Kollectaball Hopper.Thank-you for purchasing a Kollectaball Hopper.
Kollectaball Hopper is the clever way to collect and feed tennis and pickleballs,Kollectaball Hopper is the clever way to collect and feed tennis and pickleballs,
allowing more time for playing and less time and eort collecting!allowing more time for playing and less time and eort collecting!
Kollectaball comes unassembled to allow for more cost-eective and safer shipping.
Assembly will require roughly 40 minutes for a rst-time assembler.
IF YOU REQUIRE ASSEMBLY ASSISTANCE, WE ARE HERE TO HELP
CALL TOLL FREE 1-888-985-1009 OR EMAIL [e-mail]

Before assembly, the following
tools are required:
1. Protective Eye Wear
2. Flat Head Screwdriver
3. Pliers
1. U-Handle (R244) x 2
2. Wire Opener Inner Shield
(R140) x 2
3. Wire Opener Bracket (R128) x 2
4. Wire Opener (R129) x 2
5. M5 Screw x 8
6. M6 Screw x 4
7. M6 Lock Nut x 2
8. M6 Nut x 4
9. M6 Lock Nut x 8
1
1
2
2 3
3
4
5
9
7
6
8
10
15
11
16 17
12
18
19
13
14
10. Crossbar Bracket (R242) x 2
11.Thumb Screw (R246) &
Washer (R247) x 2
12. Wrench x 1
13. Wire RemovalTool (R062) x 1
14. Crossbar (R241) x 1
15. Upright with Y-Joint (R249) x 2
16. Chrome Upright (R240) x 2
17. Wire (R101) x 62
18. Cone (R127) x 2
19. Wire Mounting Disk (R090) x 2

STEP 1: Assembling the Cage
The numbered white sticker on the mounting disk helps to indicate
the next available slot. Place one Wire Mounting Disk (R090) on
a at surface and insert Wire (R101) into slot #1 as shown.
You will hear it click into place.
DO NOT INSERT THE WIRE UPSIDE DOWN.
X
Insert the 2 Cones (R127)
on the inside of the cage.
Remove the white
stickers from the
mounting disks.
Secure with an M6 Lock Nut by using the wrench provided.
Do not overtighten as it may damage the cone.
For Tennis Balls Collecting Cage
Being careful not to miss any slots,
continue inserting wires in numeric
order until all 60 slots are full.
Store the 2 extra wires in case
damaged wires need to be
replaced in the future.
For Pickleballs Collecting Cage
Continue inserting wires into
EVERY 2ND SLOT. Store the 32
extra wires in case damaged wires
need to be replaced in the future.
STEP 2: Assembling the Frame
Loosen, but do not remove the
M5 screws on theY-Joint of
each R249 Upright.
Insert the two R244 U-Handles into the
Y-Joint of both R249 Uprights so the holes line
up and fasten using M5 screws and lock nuts.
DO NOTTIGHTEN SCREWS and MAKE SURE
THE PLASTIC FEET ON THE U-HANDLES ARE
FACING DOWN.
Place the assembled Base on a
at surface and tighten the six M5
screws to theY-Joint.
Insert wire #1 from the
complete mounting disk
into slot #1 on the 2nd disk.
Continue in numeric order
until the cage is complete.

STEP 3: Wire Opener Assembly
STEP 4: Attaching the Cage
to the Cage Holder
STEP 5: Adjusting the Cage Height
Place R242 Bracket on the outside of
R240 Chrome Upright so the holes line up.
Insert two M5 Screws. Repeat with the
other Bracket and Chrome Upright.
Attach the R241 Crossbar to one of the R240 Chrome
Uprights by lining up the inserted screws with the holes
of the crossbar. Secure with M5 lock nuts. Repeat this
step on the other end of the crossbar.
Insert the H-shaped frame into the base.
Attach a R128Wire Opener Bracket to the
outside top of a R240 Chrome Upright by
lining up the holes and securing with two M6
screws and lock nuts. Repeat this step with
the other bracket and chrome upright.
Insert a R140Wire Opener Inner
Shield into an R128Wire Opener
Bracket. It will snap into place.
Spread the ends of the R129Wire Opener
and insert into the holes of the R128 Wire
Opener Bracket so it points inwards.
The Cage can be set to 5 dierent heights corresponding to the holes on the inside of
the R249 Upright. Using the R241 Crossbar, raise the cage to the desired height and
line the hole on the R240 Chrome Upright to the corresponding hole on the R249
Upright. Secure with an R246Thumb Screw and R247Washer on both uprights.
Align the holes on the ends of the cage with
the cage holder and squeeze into place.
Kollectaball is a trade mark of IntoEuropeSales Ltd. Distributed in North America by RCS Sports
You are now ready to enjoy your Kollectaball!