Barco BARCOREALITY 8200TCR+ User manual

OWNER'S MANUAL
REALITY
8200 TCR+
R9001430

BARCO PROJECTION SYSTEMS
Date :
010998
OWNER'S MANUAL
REALITY
8200 TCR+
R9001430
Art. No. :
R5975928

Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, September1998.
All rights reserved.
Trademarks are the rights of their respective owners.
BARCO n.v./Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Tel : [phone]
Fax : [phone]
E-mail : [email protected]
Visite Barco at the web : http://www.barco.com
Printed in Belgium
Federal communication commission (FCC statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Instructions to the user :
if this equipment does cause interference to radio or television reception, the user may try to correct the interference by one or more of the
following measures :
- Re-orientation of the receiving antenna for the radio or television.
- Relocate the equipment with respect to the receiver.
- Plug the equipment into a different outlet so that the equipment and receiver are on different branch circuits.
 Fasten cables connectors to the equipment by mounting screws.
Note :
The use of shielded cables is required to comply within the limits of Part15 of FCC rules and EN55022.

i-1
Table of Contents
5975928 BARCOREALITY 8200TCR+ 010998
TABLE OF CONTENTS ........................................................................................................................................................................... i-1
UNPACKING AND DIMENSIONS .......................................................................................................................................................... 1-1
Unpacking ..................................................................................................................................................................................... 1-1
Projector dimensions..................................................................................................................................................................... 1-1
Battery installation in the RCU...................................................................................................................................................... 1-2
INSTALLATION GUIDELINES ................................................................................................................................................................ 2-1
Environment .................................................................................................................................................................................. 2-1
What about ambient light ? ........................................................................................................................................................... 2-1
Which screen type? ......................................................................................................................................................................2-1
What image size? How big should the image be? ...................................................................................................................... 2-1
Where to install the projector? ......................................................................................................................................................2-2
How to install a projection lens? ...................................................................................................................................................2-2
LOCATION AND FUNCTIONS OF CONTROL ...................................................................................................................................... 3-1
Front panel terminology ................................................................................................................................................................ 3-1
Control panel terminology .............................................................................................................................................................3-1
INSTALLATION SET UP......................................................................................................................................................................... 4-1
CONNECTIONS ...................................................................................................................................................................................... 5-1
Power (mains) cord connection ....................................................................................................................................................5-1
Fuses............................................................................................................................................................................................. 5-1
Switching on .................................................................................................................................................................................. 5-1
Switching to stand-by. ................................................................................................................................................................... 5-2
Switching off .................................................................................................................................................................................. 5-2
Input connections. ......................................................................................................................................................................... 5-2
Input module insertion into the projector ...................................................................................................................................... 5-2
Fixed RGB analog input (slot 1)....................................................................................................................................................5-3
Fixed 5-input slot (slot 2)............................................................................................................................................................... 5-4
Video/S-video input module .......................................................................................................................................................... 5-5
RGB analog input module. ............................................................................................................................................................ 5-6
Component input module.............................................................................................................................................................. 5-7
RGB3S/RG3sB input module........................................................................................................................................................ 5-8
Serial Digital Input ......................................................................................................................................................................... 5-9
Connecting a computer, e.g. IBM PC (or compatible), Apple Macintosh to the RS 232 input of the projector. ....................... 5-10
Set up of the baud rate for communication with a computer. ................................................................................................... 5-10
Connecting a RCVDS 05 to the projector...................................................................................................................................5-10
Connecting a VS05 to the projector............................................................................................................................................5-10
Connecting an IR Remote Receiver 800 to the projector. ......................................................................................................... 5-10
CONTROLLING....................................................................................................................................................................................... 6-1
How to use the RCU? ................................................................................................................................................................... 6-1
Projector address .......................................................................................................................................................................... 6-1
How to display a projector address? ............................................................................................................................................ 6-2
How to program an address into the RCU? ................................................................................................................................. 6-2
Picture controls with direct access. ..............................................................................................................................................6-2
START UP OF THE ADJUSTMENT MODE........................................................................................................................................... 7-1
Adjustment Mode .......................................................................................................................................................................... 7-1
RANDOM ACCESS ADJUSTMENT MODE ........................................................................................................................................... 8-1
Starting up the Random Access Adjustment Mode......................................................................................................................8-1
File service .................................................................................................................................................................................... 8-1
Load file ......................................................................................................................................................................................... 8-2
Edit file........................................................................................................................................................................................... 8-2
Rename ......................................................................................................................................................................................... 8-5
Copy .............................................................................................................................................................................................. 8-5
Delete ............................................................................................................................................................................................ 8-6
File Options ................................................................................................................................................................................... 8-6
Picture Tuning ............................................................................................................................................................................... 8-6
CTI ON/OFF .................................................................................................................................................................................. 8-7
Still Video....................................................................................................................................................................................... 8-7
Color Temperature ........................................................................................................................................................................ 8-7
Gamma.......................................................................................................................................................................................... 8-8
Decoding ....................................................................................................................................................................................... 8-8
Dynamic Color Depth .................................................................................................................................................................... 8-8
Noise Reduction ............................................................................................................................................................................ 8-8
Edge Enhancement....................................................................................................................................................................... 8-9
Geometry....................................................................................................................................................................................... 8-9
Shift ............................................................................................................................................................................................... 8-9
Size.............................................................................................................................................................................................. 8-10
Side keystone.............................................................................................................................................................................. 8-10
Blanking ....................................................................................................................................................................................... 8-11

i-2
Table of Contents
5975928 BARCOREALITY 8200TCR+ 010998
Options ........................................................................................................................................................................................8-11
INSTALLATION MODE ........................................................................................................................................................................... 9-1
Starting up the Installation Mode .................................................................................................................................................. 9-1
Input Slots ..................................................................................................................................................................................... 9-1
800 Peripheral ............................................................................................................................................................................... 9-2
Convergence ................................................................................................................................................................................. 9-2
Configuration ................................................................................................................................................................................. 9-5
OSD color ...................................................................................................................................................................................... 9-5
No Signal ....................................................................................................................................................................................... 9-5
Internal Patterns ............................................................................................................................................................................ 9-6
SERVICE MODE ................................................................................................................................................................................... 10-1
Starting up the Service Mode...................................................................................................................................................... 10-1
Identification ................................................................................................................................................................................ 10-2
Change Password ....................................................................................................................................................................... 10-3
How to enable or disable the password function ?.....................................................................................................................10-3
How to change the password ? ..................................................................................................................................................10-3
Change Language....................................................................................................................................................................... 10-4
Change Projector Address .......................................................................................................................................................... 10-4
Change Baudrate PC ..................................................................................................................................................................10-4
Reset Lamp Runtime .................................................................................................................................................................. 10-4
Lamp Run Time History .............................................................................................................................................................. 10-5
Lamp Control ............................................................................................................................................................................... 10-5
BARCO logo ................................................................................................................................................................................ 10-5
Panel Adjustments ...................................................................................................................................................................... 10-6
Preset Input Balance................................................................................................................................................................... 10-6
I2C diagnosis. ............................................................................................................................................................................. 10-6
Appendix A : Standard Source Set Up Files .......................................................................................................................................... A-1
Appendix B : Lenses .............................................................................................................................................................................. B-1
Focusing the lens ......................................................................................................................................................................... B-1
Lens Cleaning Procedure............................................................................................................................................................. B-1
Lenses .......................................................................................................................................................................................... B-2
Appendix C : Source numbers 80 - 89 and 90 - 99 ............................................................................................................................... C-1

1-1
Unpacking and Dimensions
5975928 BARCOREALITY 8200TCR+ 010998
1
1 234 5
379
Pull
To open
4
630 135
702 52,8
978,4
1023,4
27,1
72,1
195
41,5
323
284
569
UNPACKING AND DIMENSIONS
Unpacking
To open the banding, pull on the clip as shown in the first drawing.
Take the projector out of its shipping carton and place it on a table.
For transportation, the projector is mounted on a wooden board with 3 bolts. Use a 13 mm wrench to remove these bolts.
When using the projector as a table mounted configuration, always mount the 3 supporting feet (see drawing below). These feet are mounted
on the same wooden board. Each foot contains one metal part and two plastic parts. To remove the feed, first turn out both plastic parts.
To remove the metal parts from the board, remove the retaining bolts. Save these bolts because these bolts must be used to mount the feet
to the projector. Mount first the metal parts with the removed bolts and turn in then both plastic parts to finish the feet.
Warning : To prevent overheating of the projector as table mounted, always remove the wooden board and turn in the 3 supporting feet
to allow air circulation via the built-in dust filter at the bottom.
Save the original shipping carton and packing material, they will be
necessary if you ever have to ship your projector. For maximum
protection, repack your projector as it was originally packed at the
factory.
Contents of the complete unit (box) :
Projector Dimensions
(units : mm)
25.4 mm = 1"
- 1 BARCOREALITY 8200TCR+ (weight ± 78 kg)
- 1 remote control unit RCU + 9V battery
- 1 power cable with outlet plug type CEE7.
- 1 owners manual
- 1 safety manual
- 3 supporting feet (built up in 3 parts)

1-2
Unpacking and Dimensions
5975928 BARCOREALITY 8200TCR+ 010998
310a.DRW
Battery Installation in the RCU.
A battery (not yet installed to save the battery life time) is delivered inside the plastic bag with the power
cord. To install the battery, remove the battery cover on the backside of the remote control by pushing
the indicated handle a little to the bottom of the RCU. Lift up the top side of the cover at the same time
(fig. 1).
Insert the new 9 V battery (type E-block or equivalent) in the lower compartment and connect the battery
to the contact plate.
Insert the battery into the lower compartment and put the cover back.
Note : projector address has to be programmed on the RCU before using the RCU (see chapter
'Controlling').
fig.1
fig.2
Insert here the 'Insert card
RCU' which you can cut out
onthelast page ofthismanual.
Contact
plate
Battery

2-1
Installation Guidelines
5975928 BARCOREALITY 8200TCR+ 010998
2INSTALLATION GUIDELINES
6FUHHQZLGWK
Installation guidelines
Careful consideration of things as image size, ambient light level,
projector placement and type of screen to use are critical to the
optimum use of the projection system.
* Environment
Do not install the projection system in a site near heat sources such
as radiators or air ducts, or in a place subject to direct sunlight,
excessive dust or humidity. Be aware that room heat rises to the
ceiling; check that temperature near the installation site is not
excessive.
* What about ambient light ?
The ambient light level of any room is made up of direct or indirect
sunlight and the light fixtures in the room. The amount of ambient light
will determine how bright the image will appear. So, avoid direct light
on the screen.
Windows that face the screen should be covered by opaque drapery
while the set is being viewed. It is desirable to install the projecting
system in a room whose walls and floor are of non-reflecting material.
The use of recessed ceiling lights and a method of dimming those
lights to an acceptable level is also important. Too much ambient light
results in a wash out of the projected image. That appears as less
contrast between the darkest and lightest parts of the image. With
bigger screens, the wash out becomes more important. As a general
rule, darken the room to the point where there is just sufficient light
to read or write comfortably. Spot lighting is desirable for illuminating
small areas so that interference with the screen is minimal.
* Which screen type?
There are two major categories of screens used for projection
equipment. Those used for front projected images and those for rear
projection applications.
Screens are rated by how much light they reflect (or transmit in the
case of rear projection systems) given a determined amount of light
projected toward them. The GAIN of a screen is the term used. Front
and rear screens are both rated in terms of gain. The gain of screens
range from a white matte screen with a gain of 1 (x1) to a brushed
aluminized screen with a gain of 10 (x10) or more. The choice
between higher and lower gain screens is largely a matter of
personal preference and another consideration called the Viewing
angle.
In considering the type of screen to choose, determine where the
viewers will be located and go for the highest gain screen possible.
A high gain screen will provide a brighter picture but reduce the
viewing angle.
For more information about screens, contact your local screen
supplier.
* What image size? How big should the image be?
The projector is designed for projecting an image size (video) from
1.00m (3.3ft) to 15.00m (49.2ft) with a aspect ratio of 4 to 3.
Max. ambient temperature : 40 °C.
Min. ambient temperature : 0 °C.
The projector will not operate if ambient air temperature falls outside
this range (0°C- 40°C).

2-2
Installation Guidelines
5975928 BARCOREALITY 8200TCR+ 010998
B = Distance between ceiling and top of the screen or
between floor and bottom of the screen.
A = Correction value, distance between bottom side of
projector (without feed) and middle of the lens. Value to be
subtracted from B to obtain the correct installation position. (A
value is a constant value for all screen widths and type of
lenses, A = 195 mm.)
CD = Total distance between projector and ceiling or projector
and floor.
SW = Screen width.
SH = Screen height (image height).
PD = Projector Distance, distance between screen and
projector.
Lens type selection.
a) determine the required screen width.
b) determine the approximate position of the projector in the projection
room with regard to the screen and measure the
projector-screen distance (PD).
c) use the lens formulas in appendix B to find the best corresponding
PD with regard to the measured projector-screen distance for the
required screen width.
The desired lens is determined (the order number is given in the tabel
in the same appendix B).
Start the installation procedure for the projector as described in
the manual.
Inputs and computer video format input compatibility :
Some examples :
VIDEO and S-VIDEO
COMPONENTVIDEO
RGB ANALOG with STANDARD SYNC (SYNC ON GREEN or
SEPARATE SYNC)
RGB ANALOG with TRI-LEVEL SYNC (SYNC ON GREEN or
SEPARATE SYNC)
VGA : 640 x 480 pixels
MAC : 640 x 480 pixels
Super VGA : 800 x 600 pixels
XGA : 1024 x 768 pixels
SXGA : 1280 x 1024 pixels
Up to 1600 x 1280 pixels
Sources with pixel clock < 200 MHz
* How to install a projection lens?
The projector is supplied without any lens.
The following lenses are available as an option :
QHD(1.2:1)
QHD(2.2:1)
HD(3.3:1)
QHD(4.0:1)
HD(5:1)
HD(7:1)
QHD(1.5-3:1)
WHD(3.5:1)
How to install the lens?
Remove the foam rubber in the opening of the lens holder.
- Take the new lens out of its shipping carton and remove the lens
covers.
- Turn the lens into the lens holder by turning clockwise.
- Focus the lens (see appendix B) and secure the correct position
with the fastener ring by turning this ring clockwise.
Screen
PD
B
Ceiling
Projector
CD
A
CD = B - A
SH
Optical axis projection lens
SH
SW
SIDE VIEW
BACK VIEW
Screen
CEILING VIEW
SW
Ceiling
Screen
PD
B
Floor
Projector
CD
A
CD = B - A
SH
Optical axis projection lens
SH
SW
SIDE VIEW
BACK VIEW
Screen
TOP VIEW
SW
Floor
Definitions of the Abbreviation on drawings
* Where to install the projector?

3-1
Location and Functions of Control
5975928 BARCOREALITY 8200TCR+ 020798
3
RS232 IN
REMOTE
PROJECTORMODE:
GREEN- OPERATION
RED - S TANDBY
COMMUNICATION PORT
(800-PERIPHERALS)
RS232 OUT IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOSTICS
CODE IR-RECEIVER
9
$
+]
0
I
This device com plies withPa rt 15 of the FCC rules. O peration
is subject to following two c onditions :
(1) Th isdevice may notcause harmfu linterference
(2) This device mu st accept any interference received
including interference that m ay cause u ndesired operation
  





SDI IN SDI OUT

LOCATION AND FUNCTIONS OF CONTROL
Front Panel Terminology
IR-Received : IR signals are received but not recognized
by the projector.
Diagnostics code : a) source number
b) error code : a two digits error code is displayed when
something goes wrong inside the projector.
IR receiver : receiver for control signals transmitted from
the RCU.
Power switch : '1' = on, '0' = off
Power input : autoranging from 200 to 240 Vac.
Identification plate : name, serial number, art. number.
Voltage identification plate : name, art. number.
1
2
3
RS232 IN : to allow communication with external compu-
ter, e.g. IBM PC or compatible, Macintosh ...
RS232 OUT : used to connect to next projector, RS232IN
plug (communication link for PC or MAC to the next
projector).
Communication port : allows communication with the
800 peripherals.
Remote : remote input for wired remote control.
Projector mode indication : indicates the status of the
projector.
Light off : power switch is not pressed.
Red light : power switch is pressed, projector in
stand by mode.
Green light : projector in operational mode.
IR-Acknowledged : IR signals are recognized.
4
5
Control Panel Terminology
a. Local keypad
Gaining access
6
7
8
9
10
11
12
The keypad is located behind a door, screened with the name
of the projector.
To open the door, push once on the indicated side of the door
and turn it to the front side of the projector.
13 SDI IN - SDI OUT (option): Serial digital input and loop trough
output.
2 x BNC terminals.

3-2
Location and Functions of Control
5975928 BARCOREALITY 8200TCR+ 020798
-+
-+
-+
-+
-+
0
9
78
6
5
43
21
(17(5












32a
3$86(
-+
3+$6(
)5((=


7(;7
(;,7
$'-
67%<
6+$531(66
7,17
&2/25
%5,*+71(66
&2175$67
+(/3
?

COLOR
PHASE
SHARPN TINT BRIGHTN
STANDBY
ENTER
TEXT
EXIT
PAUSE









&2175$67









b. Remote control
This remote control includes a battery powered infrared (IR) trans-
mitter that allows the user to control the projector remotely.
This remote control is used for source selection, control,
adaptation and set up. It includes automatic storing of :
- picture controls (Brightness, Sharpness...)
- settings
Other functions of the remote control are :
- switching between standby and operational mode.
- switching to "pause" (blanked picture, full power for immediate
restarting)
- direct access to all connected sources.
- variable adjustment speed : when pushing continuously on the
control disc or the picture keys, the adjustment will be executed
in an accelerated fashion.
Remote Control (RCU)
Local keypad
Terminology
Back Light Key : has no function for this projector.
ADJ. : ADJUST key, to enter or exit the adjustment mode.
Address key (recessed key), to enter the address of the
projector (between 0 and 9). Press the sunk address key
with a pencil, followed by pressing one digit button between
0 and 9.
STBY : stand-by button, to start projector when the power
switch is switched on and to switch off the projector
without switching off the power switch.
PAUSE : to stop projection for a short time, press 'PAUSE'.
The image disappears but full power is retained for imme-
diate restarting.
Help : on line help information (not yet available)
Digit buttons : direct input selection.
Picture controls : use these buttons to obtain the desired
picture analog level (see also 'Controlling').
PHASE : used to remove the instability of the image.
TEXT : when adjusting one of the image, e.g. controls during
a meeting, the displayed bar scale can be removed by
pressing 'TEXT' key first. To re-display the bar scale on the
screen, press 'TEXT' key again. 'TEXT' key only active in
operational mode.
1
2
3
4
5
6
7
8
9
10
FREEZ : press to freeze the projected image.
ENTER : to start up the adjustment mode or to confirm an
adjustment or selection in the adjustment mode.
EXIT : to leave the adjustment mode or to scroll upwards
when in the adjustment mode.
Control Disc Key (on RCU) or '+' and '-' keys (cursor
keys): to make menu selections when in the adjustment
mode.
The control disc can move forward, backward, to the right
or to the left.
Comparision between control disc movement and the use of
the cursor keys on the local keypad :
RCU = local keypad
control disc forward = '+' key up
control disc backward = '-' key down
control disc to the right = '+' key right
control disc to the left = '-' key left
Use the '+' and '-' keys (cursor keys) : to increase or
decrease the analog level of the image controls when they
are first selected.
RC operating indication : lights up when a button on the
remote control is pressed. (This is a visual indicator to check
the operation of the remote control)
11
12
13
14
15

Installation Set Up
4-1
5975928 BARCOREALITY 8200TCR+ 010998
4
)URQW7DEOH
)URQW&HLOLQJ
5HDU7DEOH
5HDU&HLOLQJ
INSTALLATION SET UP
The projector can be installed to project images in four different
configurations : front/table, front/ceiling, rear/table and rear/ceiling.
To change the Configuration, enter the adjustment mode by pushing ADJUST orENTER.
Highlight Installation by pushing the control disc forward or backward and press ENTER
to select. The installation menu will be displayed.
ENTER displays the Installation menu.
EXIT or ADJUST returns to operational mode.
Highlight Configuration by pushing the control disc forward or backward and press
ENTER to select. The configuration menu will be displayed.
ENTER displays the Configuration menu.
EXIT returns to the path selection menu.
ADJUST returns to operational mode.
The actual selected configuration will be highlighted.
Push the control disc forward or backward to select the corresponding configuration
with regard to the projector environment. Press ENTER to confirm your selection.
ENTER to confirm the selection.
EXIT returns to the installation menu.
ADJUST returns to operational mode.
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
CONVERGENCE
CONFIGURATION
OSD COLOR
INTERNAL PATTERNS
Select with or
then <ENTER>
<EXIT> to return.
ADJUSTMENT MODE
Select a path from below :
RANDOM ACCESS
INSTALLATION
SERVICE
Source 01
Select with or
then <ENTER>
<EXIT> to return.
CONFIGURATION
FRONT/TABLE
FRONT/CEILING
REAR/TABLE
REAR/CEILING
Select with or
then <ENTER>
<EXIT> to return.

Installation Set Up
4-2 5975928 BARCOREALITY 8200TCR+ 010998

5-1
Connections
5975928 BARCOREALITY 8200TCR+ 010998
5
RGBV RGB
H/ C V
On
98 27910
RGB
H / C V
H
9, '(2,1387
9,'(269,'(2
RS 232 IN
REMOTE
PROJ ECTOR MODE :
GREE N - OPER ATI ON
RED- S TANDBY
COMMU NICAT I ON P ORT
(800- PERIPHERALS)
RS232 OUT IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOS TICS
CODE IR-RECEIVER
0 I
Thisdevice complieswithP art15 of the FC C rules. O peration
issubjectto followingtwo conditions:
(1)This device maynot cause harmfulinterference
(2)This devicemus t acceptany interferencereceived
including interferencethatm aycause undesiredoperation
COLOR
PHASE
SHARPN TINT BRIGHTN
STANDBY
ENTER
TEXT
EXIT
PAUSE








&2175$67
ADJ
EXIT
STBY
TEXT
BRIGHTNESS
-
+
-
+
-
+
-
+
SHARPNESS
-
+
TINT
COLOR
CONTRAST
)5((=
0
9
7
8
6
5
4
3
2
1
(17(5
3$86(
-
+
3+$6(
+(/ 3
RGBV RGB
H / C V
H
9,'(2,1387
9,'(269,'(2
RS 232 IN
REMOTE
PROJECTORMODE :
GREEN - OPERATION
RED - STANDBY
COMMUNICATIONPORT
(800 -PERIPHERALS)
RS232 OUT IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOS TICS
CODE IR-RECEIVER
  9
$
+]
0 I
Thisdevice complieswith Part15 of the F CC rules. O peration
iss ubjecttofollowingtwoconditions:
(1) Thisdevicema y not cause harmful interference
(2) Thisdevicemu stac ceptany interferencereceived
including interfe rencethat may caus e undesiredoperation
RS232 IN
COMMUNICATIONPORT
(800-PERIPHERALS)
RS232 OUT
0I
Projector mode indication
Stand by button
Switching on
Use the power switch to switch on.
When '0' is visible, the projector is switched off.
When '1' is visible, the projector is switched on.
When switching on with the power switch, the projector starts in the
stand by mode. The projector mode indication lamp is red.
To start image projection :
a. press the 'Stand by' button on the local keypad or on the remote
control. The projector mode indication lamp will be green.
b. press a digit button to select an input source. The projector mode
indication lamp will be green.
CONNECTIONS
AC Power (mains) cord connection
Use the supplied power cord to connect your projector to the wall
outlet. Plug the female power connector into the male connector at
the front of the projector.
The power input is auto-ranging from 90 to 250 VAC.
This projector may be connected to an IT-power system.
Fuses
Warning
For continued protection against fire hazard :
- refer replacement to qualified service personnel
- ask to replace with the same type of fuse.
Fuse type : T16 AH/250V
110 -240V
10A - 4.5
60 - 50 Hz

5-2
Connections
5975928 BARCOREALITY 8200TCR+ 010998
RGB V RGB
H/C V
On
9827910
RGB
H/C V
H
9,'(2, 1 387
9,'(269,'(2
RS232 IN REMOTE
PROJECTORMODE:
GREEN- OPERATION
RED- STANDBY
COMMUNICAT I ONPORT
(800-PERIPHERALS)
RS232OUT IR-ACKNOWLEDG ED
IR-RECEIVED
DIAGNOSTICS
CODE IR-RECEIVER
9
$
+]
0 I
This device complie sw ithP art15 oftheFC C rules. Operation
issubjecttofollowingtwoconditions:
(1)Thisdevicemaynot causeharmfulinterference
(2)Thisdevicemustacceptany interferencereceived
includinginterferencethatm aycause undesiredoperation
SDI IN SDI O U T
- Reconnect the power cord to the wall outlet and switch on the
projector.
The new installed module can be selected with the digit buttons on
the RCU or the local keypad.
Input Connections.
The projector has three fixed and two modular input
facilities. The modular input slots (slot 3 and 4) can be filled
up with the following modules :
Video, S-video input order no. : R9827900
RGBS/RGsB analog input order no. : R9827910
RGB3S/RG3sB input order no. : R9827920
Component Video order no. : R9827930
The sequence of insertion has no importance. Duplicated
inputs can be used.
Note : When using a RCVDS05 or VS05, the input configu-
ration of the projector must be as follows:
Slot 1 : not used
Slot 2 : RGB and Component video input
Slot 3 : Video input module
Slot 4 : not used
When using a RCVDS05, it is recommended to use a 5-cable
output module in the RCVDS. The outputs of this module has
to be connected to slot 2 of the projector.
To switch the projector in the 5-cable mode see chapter
'Installation mode'.
Input module insertion into the projector :
- Power down the projector and disconnect the power cord
from the wall outlet.
- Remove the dummy plate covering the chosen input slot
by turning out both screws.
- Slide the input module in the free slot. Insure the module
is seated correctly in the guide grooves.
- Press on both handles of the input module until the module
plug seats in the connector of the projector.
- Secure the input module by tightening both retaining
screws.
Switching to Stand-by.
When the projector is running and you want to go to stand-by, press
the stand-by key.
Switching Off
To switch off:
- First press STANDBY key and let the projector cool down or until
the fans stop blowing or at least 15 min.
- Switch off the projector with the power switch.
WARNING : When switching to standby, never restart the
projector (hot restrike) within the first 3 minutes to avoid
damage to the lamp.
Lamp Run Time
When the total run time of the lamp is 970 hours or more, the following warning message
will be displayed for 1 minute. This warning message will be repeated every 30 minutes.
Press EXIT to remove the message before the minute is over.
When the total run time of the lamp is 1000 hours or more, the following warning message,
with the exact run time is displayed on the screen.
Lamp run time is 1000 hours. Operating the lamp longer than 1000 hours may damage
the projector. Please replace the lamp.
When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min.
The total lifetime of the lamp for a safe operation is 1000 hours max. (normal power mode,
or 500 hours in boost mode). Do not use it longer. Always replace with a same type of
lamp. Call a BARCO authorized service technician for lamp replacement.
Warning : Using a lamp for more than 1000 hours is dangerous as the
lamp could explode.
Lamp run time
980 h
<ENTER> to continue
WARNING
Lamp run time is 1000 hours
Operating the lamp longer
than 1000 hours may damage
the projector.
Please replace the lamp

5-3
Connections
5975928 BARCOREALITY 8200TCR+ 010998
Select with or
then <ENTER>
<EXIT> to return.
21
2))
%+
*
5
9
,13 ,13
,1387
$1$/2*,17(5)$&(0+]
RGB V RGB
H / C V
On
9827910
RGB
H / C V
H
9,'(2,1387
9,'(269, '(2
RS 232 IN
REMOTE
PROJECTOR MODE :
GREEN - OPE RATI ON
RED- STA NDBY
COMMUNI CAT ION P ORT
(800-PERIPHERALS)
RS232 OUT IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOSTICS
COD E IR-RECEIVER
SDI IN SDI OUT
Fixed RGB analog input (slot 1)
Slot 1 has RGB analog input terminals (BNC) with separate Horizontal
and Vertical sync (RGBHV) or with composite sync input (RGBS).
Always use an interface when a computer and local monitor have
to be connected to the projector. BARCO makes a range of
intertfaces :
Universal analog interface.
Order number : R9826100.
RGB 120 MHz analog interface.
Order number : R9826570.
VGA interface
Order number 120V : R9828079.
Order number 230V : R9828070
MAC interface
Order number 120V : R9828059
Order number 230V : R9828050
MAGIK interface
Order number 120V : R9828129
Order number 230V : R9828120
RGB analog input : 5 x BNC
Red : 0.7 Vpp ± 3 dB
Blue : 0.7 Vpp ± 3 dB
Green : 0.7 Vpp ± 3 dB
Vert. sync : 1 Vpp to 4 Vpp ± 3 dB
Hor. sync / Composite sync :
1 Vpp to 4 Vpp ± 3 dB
All input signals are always 75 ohm terminated, even in the "not
selected" mode.
Slot 1 selection :
Key in 1on the RCU or the local keypad.
Sync selection on the 'Input slots' menu.
The horizontal sync input can be set as separate sync, as separate
sync + video or as separate sync tri-level sync. To change this
setting, press ADJUST or ENTER key to start up the Adjustment mode.
Push the control disk up or down to select Installation and press
ENTER.ADJUSTMENT MODE
Select a path from below :
RANDOM ACCESS
INSTALLATION
SERVICE
INSTALLATION
INPUT SLOTS
800 PERIPHIRAL
CONVERGENCE
CONFIGURATION
INPUT SLOTS
Slot Module type [Config]
1. RGB-SS [CV]
2. RGB-SOG
3. Video [Video]
4. Component Video
Use the control disk to select 'Input Slots' by pushing up or down and
press ENTER. The internal system will scan the inputs and displays
the result in the 'Input Slots' menu.
Push the control disk up or down to select the first slot. To change
the sync priority for Sync separate, press ENTER key to toggle
between CS or HS&VS and 3LSS or CV.
Possible indication :
RGB-SS [CS or HS&VS] = separate sync is composite
sync or horizontal and vertical sync.
RGB-SS [3LSS or CV] = separate sync is composite
tri-level sync or composite video.
Select with or
<ENTER> to toggle
<EXIT> to return.

5-4
Connections
5975928 BARCOREALITY 8200TCR+ 010998
RGB V RGB
H/ C V
H
RS232IN
REMOTE
PROJECTOR MODE :
GREEN - OPERATI ON
RED- STANDBY
COMMUNICATIONPORT
(800-PERIPHERALS)
RS232 OUT IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOSTICS
CODE
Fixed 5-Input Slot (slot 2)
Slot 2 has 5 BNC input terminals.
The following signals can be connected to these BNC connectors :
Connector name R G B H V
Input signal
RGBHV R G B H V
RGBS R G B S -
RGsB R Gs B - -
Composite Video - Video - - -
Super Video - Y - - C
Component Video - SS R-Y Y B-Y S -
Component Video - SOY R-Y Ys B-Y - -
Slot 2 selection :
Key in 2 on the RCU or the local keypad.
Selection of the signal format on the 'Input slot' menu.
To change the signal format, press ADJUST or ENTER key to
start up the Adjustment mode.
Push the control disk up or down to select Installation and press
ENTER.
Use the control disk to select 'Input Slots' by pushing up or down
and press ENTER. The internal system will scan the inputs and
displays the result in the 'Input Slots' menu.
Push the control disk up or down to select the second slot. To
change the input signal priority, press ENTER key to toggle.
Possible indication :
RGB-SS [CS or HS&VS] = RGB analog signals, separate sync
is composite sync or horizontal and vertical sync.
RGB-SS [3LSS or CV] = RGB analog signals, separate sync
is composite tri-level sync or composite video.
RGB-SOG [SOG or 3LSOG] = RGB analog signals, sync on
green is composite sync or composite tri-level sync.
COMPONENT VIDEO - SS [SS or 3LSS] = separate sync is
composite sync or composite tri-level sync.
COMPONENT VIDEO - SOY [SOY or 3LSOY] = component
video with composite sync on Y or composite tri-level sync
on Y.
VIDEO
S-VIDEO
Select with or
then <ENTER>
<EXIT> to return.
Select with or
then <ENTER>
<EXIT> to return.
ADJUSTMENT MODE
Select a path from below :
RANDOM ACCESS
INSTALLATION
SERVICE
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
CONVERGENCE
CONFIGURATION
INPUT SLOTS
Slot Module type [Config]
1. RGB-SS [CV]
2. RGB-SOG
3. Video [Video]
4. Component Video
Select with or
<ENTER> to toggle
<EXIT> to return.
When using an RCVDS 05 with a 5 cable output module, connect
these 5 cables to this fixed 5-input slot (slot2) of the projector.
All sources of the RCVDS can now be accepted by the projector.

5-5
Connections
5975928 BARCOREALITY 8200TCR+ 010998
S-VIDEO
9827900
VIDEO
LR
AUDIO
9,'(269,'(2,1387
On On
TV tuner, e.g.
TVDM 40 stereo
VCR
Audio amplifier
Composite
Video
VCR S-VHS
Luma/Chroma
RGB V RGB
H / C V
On
98 27910
RGB
H / C V
H
9,'(2 ,1387
9,'(2
69,'(2
RS232IN
REMOTE
PROJECTORMODE:
GREEN - OPERATI ON
RED - STANDBY
COMMUNICATI ON PORT
(800-PERIPHERALS)
RS232 OUT IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOSTICS
CODE IR-RECEIVER
SDI IN SDI OU T
Select with or
then <ENTER>
<EXIT> to return.
Select with or
then <ENTER>
<EXIT> to return.
)ORDWLQJ

RU

QRQ

IORDWLQJ

LQSXW
Floating
Non-Floating
-
-
-
Video/S-video Input Module
To the Video input :
Composite video signals from a VCR, OFF air signal decoder, etc...
1 x BNC 1.0Vpp ± 3 dB
To the S-Video input :
Separate Y-luma/C-chroma signals for higher quality playback of
Super VHS-signals.
1 x 4 pins plug (mini DIN)
pin configuration :
1 ground luminance
2 ground chrominance
3 luminance 1.0 Vpp ± 3 dB
4 chrominance 282 mVpp ± 3 dB
Input selection :
Key in the corresponding slot number on the RCU or the local
keypad. Depending on the priority setting in the Input slots
menu, Video or S-Video will be displayed. If the wrong source
type is displayed, start up the adjustment mode by pressing
ADJUST or ENTER.
Push the control disk up or down to highlight Installation and press
ENTER to display the 'Installation menu'.
EXIT returns to operational mode.
Use the control disk to select 'Input Slots' by pushing it up or down
and press ENTER. The internal system will scan the inputs and
displays the result in the 'Input Slots menu'.
Push the control disk up or down to select the corresponding (video
or S-video) input slot number.
To change the priority between Video and S-Video, press ENTER key
to toggle.
Straps on module level.
Floating or non-floating input.
Video input :
J11 : strap "yes" : non floating strap "no" : floating
S-Video input :
J12 : strap "yes" : non floating strap "no" : floating
J13 : strap "yes" : non floating strap "no" : floating
Factory preset : strap on, input non floating.
Video input
Audio input not
available
S-Video input
INPUT SLOTS
INSTALLATION
INPUT SLOTS
800 PERIPHERAL
CONVERGENCE
CONFIGURATION
ADJUSTMENT MODE
Select a path from below :
RANDOM ACCESS
INSTALLATION
SERVICE
Select with or
<ENTER> to toggle
<EXIT> to return.
Slot Module type [Config]
1. RGB-SS [CV]
2. RGB-SOG
3. Video [Video]
4. Component Video

5-6
Connections
5975928 BARCOREALITY 8200TCR+ 010998
RGBH / C V
On
5*%$1$/2*,1387
98 27910
)ORDWLQJRUQRQIORDWLQJLQSXW
Floating
Non-Floating
-6\QFVHOHFWLRQ
6HSDUDWHV\QF 6\QFRQJUHHQ
-
-
-
-
-
21
2))
%+
*
5
9
,13 ,13
,1387
$1$/2*,17(5)$&(0+]
RGBV RGB
H/ C V
On
98 27 910
RGBH / C V
H
9,'(2,1387
9,'(2
69,'(2
RS 232 IN
REMOTE
PROJECTOR MODE :
GREEN - OP ERATI ON
RED- STA NDBY
COMMUNICATIONPORT
(800-PERIPHERALS)
RS232 OUT IR-ACKNOWLEDGED
IR-RECEIVED
DIAGNOSTICS
CODE IR-RECEIVER
SDI IN SDI OUT
Vert. sync
Hor. sync or Composite
sync
Blue
Green
Red
RGB Analog Input Module.
RGB analog input terminals with separate Horizontal and Vertical
sync inputs(RGB-HV), with Composite sync input(RGB-S) or with
Sync signals on green(RGsB).
Always use an interface when a computer and local monitor have
to be connected to the projector. See 'slot 1' for interfaces to be
applied.
RGBS/RGsB analog : 5 x BNC
Red : 0.7 Vpp ± 3 dB
Blue : 0.7 Vpp ± 3 dB
Green : 0.7 Vpp ± 3 dB
1 Vpp ± 3 dB if sync on green
Vert. sync : 1 Vpp to 4 Vpp ± 3 dB
Hor. sync / Composite sync :
1 Vpp to 4 Vpp ± 3 dB
All input signals are always 75 ohm terminated, even in the "not
selected" mode.
RGB input selection :
Key in the corresponding slot number on the RCU or the local keypad.
Straps on module level :
Floating or non-floating input.
Red : J3 : strap "yes" : non floating strap "no" : floating
Green : J4 : strap "yes" : non floating strap "no" : floating
Blue : J5 : strap "yes" : non floating strap "no" : floating
H/C : J6 : strap "yes" : non floating strap "no" : floating
V : J7 : strap "yes" : non floating strap "no" : floating
Factory preset : strap "yes", non floating input
Sync selection : strap on module level.
J8 : see drawing
Factory preset : separate sync.
Sync selection on the Input Slots menu.
The horizontal sync input can be set as separate sync input or as
separate sync + video input. To change this setting, press ADJUST
or ENTER key to start up the Adjustment mode..