Barco PGWX-62L(-K) User manual

User manual

Doc. Revision: 00
Barco nv Projection Division
Noordlaan 5, B-8520 Kuurne
Phone: [phone]
Fax: [phone]
Support: www.barco.com/en/support
Visit us at the web: www.barco.com

Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to
the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or
changes to the product(s) and/or the program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the
information in this publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site
www.barco.com or from the secured Barco web site https://my.barco.com.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded,
transmitted or stored in a retrieval system without the prior written consent of Barco.
EN55022/CISPR22 Class A ITE (InformationTechnology Equipment)
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the class B ITE limits. Such
equipment should not be restricted in its sale but the following warning shall be included in the instructions for use:
Warning :This is a class A product. In a domestic environment this product may cause radio interference in which case
the user may be required to take adequate measures.
Federal Communications Commission (FCC Statement)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the
FCC rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment.This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area may cause harmful interference, in which case the user will be
responsible for correcting any interference at his own expense.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On
receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for
material and manufacturing faults Barco must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the
date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco
can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves
to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the
contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage
attributed to the operation of software as well as to other services provided by Barco, being a component of the system
or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of
properties guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are
handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the
goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered
invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic
circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the
guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be
complied with by the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their
respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as
advertising for the products or their manufacturers.

5
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
1. SAFETY..................................................................................................................................................................................6
1.1 General considerations.................................................................................................................................................... 6
1.2 Important safety instructions............................................................................................................................................ 7
2. INTRODUCTION...................................................................................................................................................................11
2.1 Installation requirements................................................................................................................................................ 11
2.2 Projector package overview...........................................................................................................................................12
2.3 Product Overview .......................................................................................................................................................... 13
2.3.1 Main Unit ............................................................................................................................................................. 13
2.3.2 Input/Output (I/O) Panel.......................................................................................................................................14
2.3.3 Remote Control.................................................................................................................................................... 15
3. INSTALLATION.....................................................................................................................................................................16
3.1 RCU Battery Installation ................................................................................................................................................ 16
3.2 Installing the Lens.......................................................................................................................................................... 17
3.2.1 Lens Selection ..................................................................................................................................................... 17
3.2.2 Installing the lens for the first time .......................................................................................................................17
3.3 Connecting the Projector ............................................................................................................................................... 18
3.3.1 Connecting to a Computer or Laptop ..................................................................................................................18
3.3.2 Connecting to Video Sources .............................................................................................................................. 19
3.3.3 Installing the cable cover ..................................................................................................................................... 20
3.4 Powering On/Off the Projector....................................................................................................................................... 21
3.4.1 Powering On the Projector...................................................................................................................................21
3.4.2 Powering Off the Projector .................................................................................................................................. 21
3.5 Adjusting the Projected Image....................................................................................................................................... 22
3.6 Safety Cover Installation ................................................................................................................................................24
3.7 Ceiling Mount Installation...............................................................................................................................................25
4. USER CONTROLS...............................................................................................................................................................26
4.1 On-Screen Display Menus.............................................................................................................................................26
4.1.1 Using the OSD Lite Menus ..................................................................................................................................26
4.1.2 Using the Advanced OSD Menus ........................................................................................................................28
4.1.2.1 Input Menu........................................................................................................................................................ 29
4.1.2.2 Image Menu...................................................................................................................................................... 30
4.1.2.3 Layout Menu ..................................................................................................................................................... 32
4.1.2.4 Light Source Menu ...........................................................................................................................................33
4.1.2.5 Alignment Menu................................................................................................................................................ 34
4.1.2.6 Control Menu .................................................................................................................................................... 36
4.1.2.7 Service Menu.................................................................................................................................................... 37
4.2 Color Coordinate Adjustment......................................................................................................................................... 38
4.3 Constant Light Output.................................................................................................................................................... 40
5. TROUBLESHOOTING ..........................................................................................................................................................41
5.1 Image Problems............................................................................................................................................................. 41
5.2 LED Indication Chart .....................................................................................................................................................42
5.3 Warning Message.......................................................................................................................................................... 43
6. MAINTENANCE & SERVICE ...............................................................................................................................................44
6.1 Replacing the Lens ........................................................................................................................................................ 44
7. SPECIFICATIONS ................................................................................................................................................................45
7.1 PGWU-62L / PGWU-62L-K ...........................................................................................................................................45
7.2 PGWX-62L / PGWX-62L-K............................................................................................................................................47
7.3 Dimensions .................................................................................................................................................................... 49
7.4 Compatibility Modes ...................................................................................................................................................... 50
8. ENVIRONMENTAL INFORMATION.....................................................................................................................................52
8.1 Disposal information ...................................................................................................................................................... 52
8.2 RoHS compliance .......................................................................................................................................................... 52
8.3 Production address........................................................................................................................................................ 54
8.4 Importers contact information........................................................................................................................................ 54
TABLE OF CONTENTS
Table of Contents

6PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
1. Safety
1. SAFETY
1.1 General considerations
About this chapter
Read this chapter attentively. It contains important information to prevent personal injury while installing and using
your PRESENT series projector. Furthermore, it includes several cautions to prevent damage to your PRESENT
series projector. Ensure that you understand and follow all safety guidelines, safety instructions and warnings
mentioned in this chapter before installing and using the PRESENT series projector. After this chapter, additional
“warnings” and “cautions” are given depending on the procedure. Read and follow these “warnings” and “cautions”
as well.
Purpose of this device:
The exclusive purpose of this device is to project images onto a screen in an indoor environment.
Clarification of the term“PRESENT series” used in this document
When referring in this document to the term “PRESENT series” means that the content is applicable for following
Barco products:
PGWX-62Ly
PGWX-62L-Ky
PGWU-62Ly
PGWU-62L-Ky
Note: This manual is applicable for multiple projector models. Consult the Barco website to know which models
are currently for sale.
Overview
General considerationsy
Important safety instructionsy
The projector is a Class 2 laser device that conforms with IEC 60825-1:2007 and CFR 1040.10 and 1040.11y
Class 2 laser product. Do not stare into Beam.
This projector has built-in Class 4 laser module. Disassembly or modification is very dangerous and shouldy
never be attempted.
Any operation or adjustment not specifically instructed by the user’s guide creates the risk of hazardous lasery
radiation exposure.
Do not open or disassemble the projector as this may cause damage by the exposure of laser radiation.y
Do not stare into beam when the projector is on.The bright light may result in permanent eye damage.y
Without following the control, adjustment or operation procedure may cause damage by the exposure of lasery
radiation.
General safety instructions
Before operating this equipment please read this manual thoroughly and retain it for future reference.y
Installation and preliminary adjustments should be performed by qualified Barco personnel or by authorizedy
Barco service dealers.
All warnings on the projector and in the documentation manuals should be adhered to.y
All instructions for operating and use of this equipment must be followed precisely.y
All local installation codes should be adhered to.y

7
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
1. Safety
Notice on safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1,
EN60950-1, UL60950-1 and CAN/CSA C22.2 No.60950-1, which are the safety standards of information technology
equipment including electrical business equipment.
These safety standards impose important requirements on the use of safety critical components, materials and
insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having
access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation
levels, mechanical stability and strength, enclosure construction and protection against the risk of fire. Simulated
single fault condition testing ensures the safety of the equipment to the user even when the equipment’s normal
operation fails.
Users definition
Throughout this manual, the term SERVICE PERSONNEL refers to persons having appropriate technical training
and experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not
limited to HIGH VOLTAGE ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in
performing a task, and of measures to minimize the potential risk to themselves or other persons.The term USER
and OPERATOR refers to any person other than SERVICE PER-SONNEL, AUTHORIZED to operate professional
projection systems.
A PRESENT series projector is intended “FOR PROFESSIONAL USE ONLY” by AUTHORIZED PERSONNEL
familiar with potential hazards associated with high voltage, high intensity light beams, ultraviolet exposure and high
temperatures generated by the laser diode and associated circuits.
Owners record
The part number and serial number are printed on a label which is stuck on the respective part. Record these
numbers in the spaces provided below. Refer to them whenever you call upon your Barco dealer regarding this
product.
Product article number
Product serial number
Dealer
1.2 Important safety instructions
To prevent the risk of electrical shock
This product should be operated from a mono phase AC power source.y
This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of they
supplied power cables are the correct one, consult your dealer. If you are unable to insert the plug into the
outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type
plug.
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord.y
To disconnect the cord, pull it out by the plug. Never pull the cord itself.
Use only the power cord supplied with your device. While appearing to be similar, other power cords have noty
been safety tested at the factory and may not be used to power the device. For a replacement power cord,
contact your dealer.
Do not operate the projector with a damaged cord. Replace the cord. Do not operate the projector if the projec-y
tor has been dropped or damaged until it has been examined and approved for operation by a qualified service
technician.
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.y
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should bey
used. A cord rated for less amperage than the projector may overheat.
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltagey
points or short out parts that could result in a risk of fire or electrical shock.
Do not look or stare into the projector’s lens when the laser projector is on.The bright
light may hurt and damage you eyes.

8PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
1. Safety
Do not expose this projector to rain or moisture.y
Do not immerse or expose this projector in water or other liquids.y
Do not spill liquid of any kind on this projector.y
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified servicey
personnel before resuming operations.
Do not disassemble this projector, always take it to an authorized trained service person when service or repairy
work is required.
Do not use an accessory attachment which is not recommended by the manufacturer.y
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended andy
unused for long periods of time, unplug it from the wall outlet.This will prevent damage to the device due to
lightning and AC power-line surges.
To prevent personal injury
To prevent injury and physical damage, always read this manual and all labels on the system before connectingy
to the wall outlet or adjusting the projector.
To prevent injury, take note of the weight of the projector.y
To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.y
Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to they
eye.
Warning: extremely high brightness laser:This projector uses extremely high brightness laser. Never attempt toy
look directly into the lens or at the laser.
Before attempting to remove any of the projector’s covers, you must turn off the projector and disconnect fromy
the wall outlet.
When required to switch off the projector, to access parts inside, always disconnect the power cord from they
power net.
The power input at the projector side is considered as the disconnect device. When required to switch off they
projector, to access parts inside, always disconnect the power cord at the projector side. In case the power input
at the projector side is not accessible (e.g. ceiling mount), the socket outlet supplying the projector shall be
installed nearby the projector and be easily accessible, or a readily accessible general disconnect device shall
be incorporated in the fixed wiring.
Do not place this equipment on an unstable cart, stand, or table.The product may fall, causing serious damagey
to it and possible injury to the user.
It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if theyy
have become visibly damaged to such an extent that their effectiveness is impaired. For example by cracks or
deep scratches.
Exposure to UV radiation: Some medications are known to make individuals extra sensitive to UV radiation.They
American Conference of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure
for an-8 hour day to be less than 0,1 micro-watts per square centimeters of effective UV radiation. An evaluation
of the workplace is advised to assure employees are not exposed to cumulative radiation levels exceeding these
government guidelines.The exposer of this UV radiation is allowed for only 1 hour per day for maintenance and
service persons.
To prevent fire hazard
Do not place flammable or combustible materials near the projector!y
Barco large screen projection products are designed and manufactured to meet the most stringent safetyy
regulations.This projector radiates heat on its external surfaces and from ventilation ducts during normal
operation, which is both normal and safe. Exposing flammable or combustible materials into close proximity
of this projector could result in the spontaneous ignition of that material, resulting in a fire. For this reason, it
is absolutely necessary to leave an “exclusion zone” around all external surfaces of the projector whereby no
flammable or combustible materials are present.The exclusion zone must be not less than 50 cm (20”) for all
DLP projectors.The exclusion zone on the lens side must be at least 5 m. Do not cover the projector or the lens
with any material while the projector is in operation. Keep flammable and combustible materials away from the
projector at all times. Mount the projector in a well-ventilated area away from sources of ignition and out of direct
sun light. Never expose the projector to rain or moisture. In the event of fire, use sand, CO2 or dry powder
fire extinguishers. Never use water on an electrical fire. Always have service performed on this projector by
authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non-Barco

9
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
1. Safety
replacement parts as they may degrade the safety of this projector.
Slots and openings in this equipment are provided for ventilation.To ensure reliable operation of the projectory
and to protect it from overheating, these openings must not be blocked or covered.The openings should never
be blocked by placing the projector too close to walls, or other similar surface.This projector should never be
placed near or over a radiator or heat register.This projector should not be placed in a built-in installation or
enclosure unless proper ventilation is provided.
Projection rooms must be well ventilated or cooled in order to avoid build up of heat.y
Let the projector cool down completely before storing. Remove cord from the projector when storing.y
To prevent projector damage
The air filters of the projector must be cleaned or replaced on regular base (a “clean” booth would be monthly-y
minimum). Neglecting this could result in disrupting the air flow inside the projector, causing overheating.
Overheating may lead to the projector shutting down during operation.
The projector must always be installed in a manner which ensures free flow of air into its air inlets andy
unimpeded evacuation of the hot air from its cooling system.
In order to ensure that correct airflow is maintained, and that the projector complies with Electromagneticy
Compatibility (EMC) requirements, it should always be operated with all of its covers in place.
Slots and openings in the cabinet are provided for ventilation.To ensure reliable operation of the product andy
to protect it from overheating, these openings must not be blocked or covered.The openings should never be
blocked by placing the product on a bed, sofa, rug, or other similar surface.This product should never be placed
near or over a radiator or heat register.The device should not be placed in a built-in installation or enclosure
unless proper ventilation is provided.
Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplugy
the mains supply immediately. Do not operate the projector again until it has been checked by qualified service
personnel.
Do not block the projector cooling fans or free air movement around the projector. Loose papers or other objectsy
may not be nearer to the projector than 30 cm (12”) on any side.
Do not use this equipment near water.y
Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room asy
high power laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the
Digital Mirror Devices™ in which case there is a loss of warranty.
Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirrory
Devices™ in which case there is a loss of warranty.
Save the original shipping carton and packing material.They will come in handy if you ever have to ship youry
equipment. For maximum protection, repack your set as it was originally packed at the factory.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Usey
a damp cloth for cleaning. Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since
these will damage the cabinet. Stubborn stains may be removed with a cloth lightly dampened with mild
detergent solution.
To ensure the highest optical performance and resolution, the projection lenses are specially treated with any
anti-reflective coating, therefore, avoid touching the lens.To remove dust on the lens, use a soft dry cloth. Do
not use a damp cloth, detergent solution, or thinner.
Rated maximum ambient temperature, ta= 40 °C (104 °F).y
This projector can be set to any angle within vertical 360° range. It can also rotate 90° into portrait orientation.y
360°

10 PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
1. Safety
Allowing the proper space of the projector cabinet is critical for proper air circulation and cooling of the unit.They
dimensions shown here indicate the minimum space required. If the projector is to be built into a compartment
or similarly enclosed, these minimum distances must be maintained.
20” (50 cm)
4” (10 cm)
20” (50 cm)
On servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerousy
voltage potentials and risk of electric shock.
Refer all servicing to qualified service personnel.y
Attempts to alter the factory-set internal controls or to change other control settings not specially discussed iny
this manual can lead to permanent damage to the projector and cancellation of the warranty.
Unplug this product from the wall outlet and refer servicing to qualified service technicians under the followingy
conditions:
When the power cord or plug is damaged or frayed.-
If liquid has been spilled into the equipment.-
If the product has been exposed to rain or water.-
If the product does not operate normally when the operating instructions are followed. Adjust only those-
controls that are covered by the operating instructions since improper adjustment of the other controls may
result in damage and will often require extensive work by a qualified technician to restore the product to
normal operation.
If the product has been dropped or the cabinet has been damaged.-
If the product exhibits a distinct change in performance, indicating a need for service.-
Replacement parts: When replacement parts are required, be sure the service technician has used originaly
Barco replacement parts or authorized replacement parts which have the same characteristics as the Barco
original part. Unauthorized substitutions may result in degraded performance and reliability, fire, electric shock
or other hazards. Unauthorized substitutions may void warranty.
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to performy
safety checks to determine that the product is in proper operating condition.
To prevent battery explosion
Danger of explosion if battery is incorrectly installed.y
Replace only with the same or equivalent type recommended by the manufacturer. (AAA LR03,1.5V)y
For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rulesy
and regulations to ensure proper disposal.

11
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
2. Introduction
2. INTRODUCTION
2.1 Installation requirements
About this chapter
Read this chapter before installing PRESENT series projector. It contains important information concerning
installation requirements for the PRESENT series projector, such as minimum and maximum allowed ambient
temperature, humidity conditions, required safety area around the installed projector, required power net, etc.
Furthermore, careful consideration of things such as image size, ambient light level, projector placement and type
of screen to use are critical to the optimum use of the projection system.
Overview
Installation requirementsy
Projector package overviewy
Environment conditions
Table below summarizes the physical environment in which the PGWX-62L/PGWU-62L/PGWX-62L-K/
PGWU-62L-K projector may be safely operated or stored.
Environment Operating Non-Operating
Ambient Temperature 5 °C (41 °F) to 40 °C (104 °F) -10°C (14°F) to 60°C (140°F)
Humidity 10% to 85% RH Non-Condensed 5% to 90% RH Non-Condensed
Altitude 0 (0Ft) to 3000m (9843Ft)
Cooling requirements
The projector is fan cooled and must be installed with sufficient space around the projector head, minimum 30 cm
(12 inch) to ensure sufficient air flow. It should be used in an area where the ambient temperature, as measured at
the projector air inlet , does not exceed +40°C (+104°F).
Clean air environment
A projector must always be mounted in a manner which ensures the free flow of clean air into the projectors
ventilation inlets. For installations in environments where the projector is subject to airborne contaminants such
as that produced by smoke machines or similar (these deposit a thin layer of greasy residue upon the projectors
internal optics and imaging electronic surfaces, degrading performance), then it is highly advisable and desirable to
have this contamination removed prior to it reaching the projectors clean air supply. Devices or structures to extract
or shield contaminated air well away from the projector are a prerequisite, if this is not a feasible solution then
measures to relocate the projector to a clean air environment should be considered.
Only ever use the manufacturer’s recommended cleaning kit which has been specifically designed for cleaning
optical parts, never use industrial strength cleaners on the projector’s optics as these will degrade optical coatings
and damage sensitive optoelectronics components. Failure to take suitable precautions to protect the projector
from the effects of persistent and prolonged air contaminants will culminate in extensive and irreversible ingrained
optical damage. At this stage cleaning of the internal optical units will be noneffective and impracticable. Damage of
this nature is under no circumstances covered under the manufacturer’s warranty and may deem the warranty null
and void. In such a case the client shall be held solely responsible for all costs incurred during any repair. It is the
clients responsibility to ensure at all times that the projector is protected from the harmful effects of hostile airborne
particles in the environment of the projector.The manufacturer reserves the right to refuse repair if a projector has
been subject to knowingly neglect, abandon or improper use.
Main Power requirements
The PRESENT series projector operates from a nominal mono phase power net with a separate earth ground PE.
Note: Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms
of guarantee. Observing the specication mentioned in this chapter is critical for projector performance.
Neglecting this can result in loss of warranty.

12 PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
2. Introduction
Projector Power requirements
PGWX-62L/PGWX-62L-K AC INPUT 100-240V, 6.5A, 50/60Hz
PGWU-62L/PGWU-62L-K AC INPUT 100-240V, 6.5A, 50/60Hz
The power cord required to connect the projector with the power net is delivered with the projector.
Projector weight
Do not underestimate the weight of the projector.The projector weights about 17.5 kg without lens. Be sure that the
pedestal or ceiling mount on which the projector has to be installed is capable of handling five (5) times the com-
plete load of the system.
Box content
This projector comes with all the items shown below. Check to make sure your package is complete. Contact your
dealer immediately if anything is missing.
2.2 Projector package overview
Projector Remote Control with two AAA size
batteries
User Guide, Quick Start
Guide, Safety Manual
Lens Cover Cable Cover Power Cord (US)
Power Cord (China) Power Cord (EU) 5V Connection Cable
Note: 5V connection cable is for use with optional modules.

13
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
2. Introduction
2.3 Product Overview
VGA-OUTVGA-IN
LANRS-232 12V
OUT
5V
OUT
CVBS
HDMI
DVI
Enter
Menu
2
1
7
4
5
6
2.3.1 Main Unit
Component Location
Note: The Projection Lens is optional item not a standard accessary in the package.
1Projection Lens Cap
2Ventilation Holes
3Control Panel
4Input/Output (I/O) Panel
5Power Switch
6Power Socket (AC Input: AC100-240V~, 50-60Hz)
7Tilt-Adjustment Feet
3

14 PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
2. Introduction
2.3.2 Input/Output (I/O) Panel
Component Location
VGA-OUT VGA-IN
LAN RS-232 12V
OUT
5V
OUT
CVBS
HDMI
DVI
2
9
1
8 5
1Monitor Connector (Loop from VGA)
2VGA Connector (PC Analog Signal/Component Video Input)
3HDMI Connector
4DVI-D Input Connector
5Video Input Connector
6+5V Relay Connector
7+12V Relay Connector
8RS232 Connector
9Networking Connector RJ45
3 4
67

15
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
2. Introduction
1Monitor Connector (Loop from VGA)
2VGA Connector (PC Analog Signal/Component Video Input)
3HDMI Connector
4DVI-D Input Connector
5Video Input Connector
6+5V Relay Connector
7+12V Relay Connector
8RS232 Connector
9Networking Connector RJ45
2.3.3 Remote Control
Button Location
8
5
3
4
2
9
10
6
7
1
1On/Off
2Home
3OK
4Arrow Right
5Arrow Up
6Arrow Left
7Arrow Down
8LED Indication
9Battery
Compartment
10 IR LED’S
Basic Remote Command (Result) Remote Lite (Action)
Start the projector Press “On/off”
Turn off the projector Press “On/off” 1> 1
Show main menu on screen Press “Home” 2
Move through menu Press “Arrow keys” 6 4
5
7
Select button Press “OK” 3
Select and return to previous menu Press “OK” 3
Return to previous menu without selecting Press “Home” 2
Clear the menu from the screen Press “Home” 2
Activate picture mute function press 2x “Arrow Up” Press any key to deactivate.
Activate picture freeze function press 2x “Arrow Left” Press 2x “Arrow Left” again to
deactivate.
Use the remote control to control these functions.
Note: The picture freeze function is not workable when PIP is activated.

16 PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
3. Installation
3.1 RCU Battery Installation
3. INSTALLATION
Overview
RCU Battery Installationy
Installing the Lensy
Connecting the Projectory
Powering On/Off the Projectory
Adjusting the Projected Imagey
Safety Cover Instalationy
Ceiling Mount Installationy
Remove the cover by sliding it in the direction indicated by the arrow.1. 1
Insert two new AAA batteries (observe the polarity).2. 2
Replace the cover.3. 3
Procedure:
Notes for the Remote Control Unit
Be sure to insert the batteries in the corresponding orientations to match the polarities.y
Do not mix new batteries with used batteries as it would shorten the life of new batteries or causey
leakage.
Only used AAA batteries as instructed; do not attempt to insert different types of batteries into they
remote control.
If the remote is going to be unused for long periods of time, be sure to remove the batteries to preventy
leakage, which could damage the remote control.
The liquid contents in the batteries is harmful to the skin; do not touch the leakage with your barey
hands directly. When installing fresh batteries, be sure to clean up the leakage thoroughly.
Under most circumstances, you only need to point the remote control towards the screen and they
IR signal would be reflected off the screen and picked up by the IR sensor on the projector. But
under specific circumstances, the projector may fail to receive signals from the remote control due to
environmental factors. When this happens, orient the remote control at the projector and try again.
If the range of effective remote control signal reception decreases or if the remote control stopsy
working, replace the batteries.
If the infrared receiver is exposed to fluorescent lamp or strong sunlight, the remote control may noty
operate normally.
Refer to the regulations enforced by your local government on the disposal of used batteries; impropery
disposal could damage the environment.
123

17
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
3. Installation
3.2 Installing the Lens
Warning: This procedure may only be performed by qualied technical service personnel.
Lens cap should be removed before installing the lens. If not it will damage the projector.1. 1
Remove the lens cap counterclockwise.2. 2
Rotate the bar upwards to release the lock.3. 3
Be sure the label “4. TOP” of lens is upward and then push the lens into the position. 4
Rotate the lens clockwise to lock the lens and then rotate the bar downwards.5. 5
Put the lens cover on the lens with the sound “click”.6. 6
Procedure:
1
56
2 3
Caution: Do not transport the projector with any lens installed.
4
Determine the required screen width (SW).1.
Determine the approximate position of the projector in the room.2.
Start up the Lens Calculator on the Barco website: http://www.barco.com/en/tools/lenscalculator to determine3.
the possible lenses for your configuration. As a result the Lens Calculator window opens.
3.2.1 Lens Selection
Procedure:
3.2.2 Installing the lens for the first time
Notes:
The Lens Calculator can also be used to determine the position of the projector when the lens type andy
screen width is known.
Due to lens tolerances the results of calculated values may be different from measured values.Thesey
difference may vary +/- 5%.

18 PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
3. Installation
3.3 Connecting the Projector
Projection Lens P/N R9832755 R9832753 R9832754 R9832756 R9832778
Lens Type Wide Zoom
Standard
WXGA/
WUXGA
Standard
WUXGA Long Zoom Ultra Long Zoom
Throw Ratio (WXGA) 1.00-1.28 1.28-1.61 --- 1.60-3.07 3.04-5.78
Throw Ratio (WUXGA) 0.95-1.22 1.22-1.53 1.22-1.53 1.52-2.92 2.90-5.50
Zoom Ratio 1.28X 1.25X 1.25X 1.9X 1.9X
Lens Specification
VGA-OUT VGA-IN
LAN RS-232 12V
OUT
5V
OUT
CVBS
HDMI
DVI
Enter
Menu
1
3
2
4
5
6
+12V Relay Output
Network Port
7
1Network Cable
2Power Cord
312V DC Jack
4RS232 Cable
5HDMI Cable
6VGA in Cable
7VGA out Cable
3.3.1 Connecting to a Computer or Laptop
Wiring Diagram

19
PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
3. Installation
3.3.2 Connecting to Video Sources
Wiring Diagram
VGA-OUT VGA-IN
LAN RS-232 12V
OUT
5V
OUT
CVBS
HDMI
DVI
Enter
Menu
3
Video Output
1
2
DVD Player, Set-top Box,
HDTV Receiver
4
5
+12V Relay Output
112V DC Jack
2Power Cord
3Composite Video Cable
4DVI-D Cable
5HDMI Cable

20 PGWX-62L/PGWU-62L/PGWX-62L-K/PGWU-62L-K - - 2015/03/06
3. Installation
3.3.3 Installing the cable cover
Procedure
Note: To remove the cable cover, reverse the previous step.
Pull the cable cover upwards to engage the cable cover with the projector.1.
Gently flip the projector over so that its top panel is facing up.2.
Rotate the screws securing the cable cover.3.