BARDI DH189 User manual

Baridi Smart Thermo Cooker, 18 Preset Functions, 7” Touch
Screen, App Guided Recipes, White
Model No. DH189
Thank you for purchasing a Dellonda product. Manufactured to a high standard, this product will, if used according to these instructions, and properly
maintained, give you years of trouble free performance.
www.dellonda.co.uk DH189 Issue:1 11/01/23

2
Important Information
Please read these instructions carefully and note any safe operational requirements, warnings & cautions. Use the product correctly and with
care for the purpose for which it is intended. Failure to do so may cause damage and/or personal injury and will invalidate the warranty. Keep
these instructions safe for future use.
Refer to
instruction
manual
Warning:
Hot
Surface
SAFETY INSTRUCTIONS
• ELECTRICAL SAFETY
• WARNING! It is the user’s responsibility to check the following:
• Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all electrical
connections for wear and damage. Baridi recommend that an RCD (Residual Current Device) is used with all electrical products. You may obtain
an RCD by contacting your local domestic stockist. If the product is used in the course of business duties, it must be maintained in a safe
condition and routinely PAT (Portable Appliance Test) tested.
• Electrical safety information: It is important that the following information is read and understood.
• Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
• Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
• Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is tted with the correct fuse - see
fuse rating in these instructions.
• DO NOT pull or carry the appliance by the power cable.
• DO NOT pull the plug from the socket by the cable.
• DO NOT use worn or damaged cables, plugs or connectors.
• Ensure that any faulty item is repaired or replaced immediately by a qualied electrician.
• This product is tted with a BS1363/A 3 pin plug. If the cable or plug is damaged
during use, switch off the electricity supply and remove from use. Ensure that repairs are
carried out by a qualied electrician.
• Replace a damaged plug with a BS1363/A 3 pin plug. If in doubt contact a qualied electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
B) Connect the BROWN live wire to the live terminal ‘L’.
C) Connect the BLUE neutral wire to the neutral terminal ‘N’.
• Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
• Dellonda recommend that installation and repairs are carried out by a qualied electrician.
• GENERAL SAFETY INSTRUCTIONS
• Read and Save These Instructions
• When using electrical appliances, in order to reduce the risk of re, electric shock and/or injury, these basic safety precautions should always
be followed:
• When using electrical appliances, basic safety precautions should always be followed, including the following:
• Before using this Thermo Cooker, read and follow all warnings and instructions in this manual, even if you are familiar with this product.
• Keep appliance out of reach of young children.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Ensure children and babies do not play with plastic bags or any packaging materials.
• This Thermo Cooker is heavy. Care should be taken when moving it. Turn off and unplug before moving.
• Do not attempt to modify this product in any way.
• This Thermo Cooker must be Earthed.
• Do not plug into the power socket before set up is completed.
• Keep Power Cord away from trafc areas and wet areas.
• VERY IMPORTANT:
• Ensure the outside of the appliance does not get wet (water splashes etc.).
• Do not use appliance with wet hands.
• Do not immerse appliance in water or other liquids or use near sinks, baths or showers.
• Always operate the appliance from a power source of the same voltage, frequency and rating as indicated on the product identication plate.
• Position the power supply lead properly so that it will not be walked on, pinched by items placed on or against it or have the appliance resting on
it.
• This Thermo Cooker is intended to be used in household and similar applications such as:
• – staff kitchen areas in shops, ofces and other working environments
• – farmhouses and by clients in hotels, motels and other residential type environments
• – bed and breakfast type environments
• – catering and similar non-retail applications
• WARNING: Keep ventilation openings clear of obstruction.
• Avoid contacting moving parts. Keep hands, hair, clothing as well as spatulas and other
• utensils away during operation to prevent injury and/or damage to the appliance.
• Switch off the appliance and disconnect from supply before changing accessories or
• approaching parts that move in use.
• Always unplug the appliance from the power supply if it is left unattended, and before assembling, disassembling or cleaning.
Replacement fuse rating:
13A

3
• Be careful if hot liquid is poured into the food processor or blender as it can be ejected out of the appliance due to a sudden steaming.
• The appliance is only to be used with the stand provided.
• The heating element surface is subject to residual heat after use.
• For cleaning, please refer to “Clean” section.
• For the operating times and speed settings for accessories, please refer to “Suggested Speed and Capacity for each Accessory” section.
• Caution, hot surface. Care must be taken. The surfaces are liable to get hot during use.
• Operate on a at level surface only. Operating on sinks, draining boards or uneven surfaces must be avoided.
• Keep hands and utensils out of the jar while in use. A rubber scraper may be used when the appliance is turned off and unplugged.
• Always operate the appliance with the Lid in place.
• Never bypass the safety interlocking devices.
• Do Not attempt to open the lid or remove the jar when in use.
• Pay attention to the high-temperature food when you open the jar lid.
• Always insert the measuring cup / Lid Plug correctly in the hole in the top of the jar lid when processing food.
• Do not exceed 2 minutes of use when set to the highest speed levels 8, 9 or 10 as the motor can overheat. Switch off and allow the unit to cool
down for at least 1 minute, then continue again.
• CAUTION: When blending / stirring hot liquids, (Never blend hot oil or fat), pour through the special removable cap on the Lid of the jar. Begin
processing at a lower speed. Keep hands and other exposed skin away from the cover to prevent possible burns.
• Injury can result if moving blades accidentally become exposed.
• Do not leave the appliance unattended when running.
• Do not use the jar for storing foods or beverages.
• Do not use appliance for mixing paints or other ammable liquids or in a location contaminated with ammable gases or vapours.
• Avoid spillage of food or liquids onto the power connector in the jar recess. If there is a spill, immediately turn off and unplug, allow the spillage to
cool, then clean.
• Make sure that the blade sealing ring is tted correctly and the blade assembly is assembled securely in the jar base before use.
• The failure of correct assembly will cause the food leakage which will damage the appliance.
• Take care after using the heating function as the surfaces of components will stay hot for some time after use.
• Ensure the jar, jar lid and steamer tray are assembled correctly when using the steamer accessories.
• When in use, do not touch any part of the steamer accessory except its handles.
• Do not use the steamer without the jar lid in place.
• When opening the steamer lid, be careful not to be scalded by escaping hot steam.
• When using any other the heating functions, take care to avoid any injury by escaping hot steam.
• Ensure that the vent hole in the steamer lid is unblocked during use.
• Take care not to knock the steamer tray off the top of the jar either during or after use.
• Do not reach for an appliance that has fallen into water. Switch ‘OFF’ at the power point and unplug immediately.
• Do not let the power cord hang over the edge of a table or counter, or touch hot surfaces.
• Do not use appliance if it has been dropped or any part of appliance (including cord or plug) has been damaged.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in order to avoid a hazard.
• The use of accessories not intended for use with this appliance may cause injuries to the user or damage to the appliance.
• Do not install the unit on other appliances, on uneven surfaces or where it could be subject to: heat sources (e.g., radiators or stoves), direct
sunlight, excessive dust or mechanical vibrations.
• Appliance should not be used outdoors, placed near a hot gas or electrical burner or placed in a heated oven.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.
• Do not operate appliance underneath or near ammable or combustible materials (e.g., curtains).
• Any type of servicing, apart from ordinary cleaning, must be carried out by qualied electrical person only. There are no user serviceable parts in
this appliance.
• If this appliance is used by a third party, please supply the instruction manual with it.
• Do not misuse the power cord. Never carry or pull the appliance by the power cord or pull to disconnect it from the outlet. Instead, grasp the plug
body and pull to disconnect.
• Do not use the unit in very hot or humid places, or under direct sunlight.
• It is not recommended to use this appliance with an extension cord or power board.
• Do not place any other appliances on top of the appliance.
• This appliance is designed for domestic use only.
• This product has not been designed for any uses other than those specied in this instruction manual.
• Contact your local council for proper instructions for disposing of the unused appliance.
• No liability can be accepted for any damage caused by non-compliance with these instructions or any other improper use or mishandling of
appliance.
• CAUTION: To prevent damage to the appliance do not use alkaline cleaning agents when cleaning, use a soft cloth and a mild detergent.
• IMPORTANT: Care is needed when handling the Multifunction Blade, emptying the Jar and especially during cleaning.
• Do not touch the sharp edge of the blades. Only handle the top part when you assemble, remove and clean the blade.
• Misuse of this Thermo Cooker may result in serious injury. Only use your Thermo Cooker for its intended domestic use.
• CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this Thermo Cooker must not be supplied through an
external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.

4
COMPONENTS
INSTALLATION
• Place the Thermo Cooker on a strong, at and level surface.
• Place your Thermo Cooker where there is no heat source nearby or direct sunlight. Splashing water on the appliance may cause a short circuit.
• For good ventilation keep enough space between the side walls and your appliance.
• Leave at least a 100mm gap between the back and sides of the Appliance and any wall.
• Leave ample space above to access the jar lid and steamer.
BEFORE FIRST USE
UNPACKING:
• Remove all packaging materials and dispose of properly and thoughtfully.
• Before using your appliance and accessories, it is strongly advised to clean components thoroughly. Refer to CLEANING section.

5
ASSEMBLY AND USE OF ACCESSORIES
• With the Appliance fully unpacked and placed in a suitable position as described previously, you are now ready to use your appliance.
DRIVE COUPLING
• If not already tted to the bottom of the jar, the drive coupling and rubber sealing gasket must be tted and secured properly.
• To do this, take the drive coupling and ensure the rubber gasket is tted over the bottom of the coupling as shown in g.1.
• Failure to t the rubber sealing gasket will allow liquids to escape out the bottom of the jar.
• From the top of the jar, lower the drive coupling down and through the hexagonal hole in the bottom of the jar g.2.
• NOTE: The drive coupling can only be fully inserted into the hexagonal hole in three positions. Not six positions of the hexagonal hole. So, if the
drive coupling cannot be inserted all the way into the hole, rotate the drive coupling one notch and push in.
• Whilst holding the drive coupling in place, ip the jar upside down.
• Take the locking collet with your other hand and with the arrow on the collet aligned with the Unlocked Padlock symbol on the base of the jar,
push the locking collet down, then with some force, rotate clockwise until the arrow is aligned with the Locked Padlock symbol to seal and lock
the Drive Coupling in place g.2.
MULTIFUNCTION BLADE FIG.3
• The Multifunction Blade is used primarily for chopping food items.
• IMPORTANT: Take extra care when handling this accessory as the blades are very sharp and may cause injury if mishandled.
• To install the Multifunction Blade, follow the steps below:
• 1. Place the jar onto the main body in the correct orientation and seat it properly.
• 2. Grasp the top of the blade post.
• DO NOT grasp or touch the sharp blade edges.
• Lower the Multifunction Blade over the top of the Drive Coupling in the bottom of the jar, ensuring to align the tabs on the drive coupling with the
slots in the bottom of the blade, then push down rmly and rotate anticlockwise until it seats in place g.4.1 & 4.2.
• Pull to ensure blade locked safely g.5.3 & 5.4.
• IMPORTANT: The jar must sit on the main body properly, or you will fail to install blade.
To remove the Multifunction Blade, follow the steps below in g.6:
1. Place the jar onto the main body in the correct orientation and seat it properly.
2. Grasp the top of the blade post, push down rmly and rotate clockwise, then pull it straight up and out.
• IMPORTANT: The jar must sit on the main body properly, or you will fail to remove blade.
fig.1
fig.2
fig.3 fig.4
fig.5

6
KNEADING BLADE FIG.7 & 8
• The Kneading Blade is used primarily for kneading dough. IMPORTANT: Do not use the Kneading Blade above speed setting 3.
• To install the Kneading Blade, follow the steps below:
• 1. Place the jar onto the main body in the correct orientation and seat it properly.
• 2. Grasp the top of the blade post.
• 3. Lower the Kneading Blade over the top of the Drive Coupling in the bottom of the jar, ensuring to align the tabs on the drive coupling with the
slots in the bottom of the blade, then push down rmly and rotate anticlockwise until it seats in place.
• 4. Pull to ensure blade locked safely.
• IMPORTANT: The jar must sit on the main body properly, or you will fail to install blade.
fig.6
fig.7
fig.8

7
• To remove the Kneading Blade, follow the steps below in g.9:
• 1. Place the jar onto the main body in the correct orientation and seat it properly.
• 2. Grasp the top of the blade post, push down rmly and rotate clockwise, then pull it straight up and out.
• IMPORTANT: The jar must sit on the main body properly, or you will fail to remove blade.
SAUTE BLADE FIG.10
• The Saute Blade is used primarily for sauteing and mixing.
• IMPORTANT: Do not use the Saute Blade above speed setting 2.
• To install the Saute Blade, follow the steps below in g.11:
• 1. Place the jar onto the main body in the correct orientation and seat it properly.
• 2. Grasp the top of the blade post.
• 3. Lower the Saute Blade over the top of the Drive Coupling in the bottom of the jar, ensuring to align the tabs on the drive coupling with the slots
in the bottom of the blade, then push down rmly and rotate anticlockwise until it seats in place.
• 4. Pull to ensure blade locked safely.
• IMPORTANT: The jar must sit on the main body properly, or you will fail to install blade.
fig.9
fig.10
fig.11

8
• To remove the Saute Blade, follow the steps below:
• 1. Place the jar onto the main body in the correct orientation and seat it properly.
• 2. Grasp the top of the blade post, push down rmly and rotate clockwise, then pull it straight up and out.
• IMPORTANT: The jar must sit on the main body properly, or you will fail to remove blade.
BUTTERFLY WHISK FIG.13
• The Buttery Whisk is used primarily for stirring and whisking food items.
• IMPORTANT: Do not use the Buttery Whisk above speed setting 4.
• Do Not add ingredients into the jar when the appliance is working with the buttery whisk,
• as the buttery whisk may get jammed and damaged.
• To install the Buttery Whisk, grasp the top of the buttery whisk g.13.A.
• Align the base of the Buttery Whisk with the top of the Multifunction Blade, push the
• Buttery Whisk down rmly until it sits in place g.13.B.
• To remove the Buttery Whisk, pull it straight up and out g.13.C.
JAR AND LID ASSEMBLY
• There are jar capacity marks on one side, inside the jar.
• The Max capacity for blending and heating is 3L.
• To attach the lid, position the lid on the top of the jar, press the lid down rmly so that it
sits at on the jar edge, then rotate the lid clockwise to lock the lid onto the jar g.14.A.
• NOTE: Unless the lid is tted and locked correctly, the Thermo Cooker cannot be started.
• To remove the lid, press the lock release button and rotate the lid anticlockwise, then lift the lid straight up and off.
• Place the jar onto the main body in the correct orientation and seat it properly.
fig.12
fig.13A
fig.14A
fig.14B
fig.14C
fig.13B
fig.13C

9
• NOTE: Unless the jar is tted and seated correctly, the Thermo Cooker can not be started.
MEASURING CUP g.15
• Measuring cup not only prevents food from being ejected from the hole in the lid, it is also a convenient measuring cup.
• To assemble the Measuring Cup to the lid, place the measuring cup into the hole, rotate clockwise to lock in place.
• To remove, rotate anticlockwise and lift straight up and out.
• IMPORTANT: The measuring cup is the only component / item which must be used to cover / block off the round hole in the Jar lid
• Do Not cover / block the hole in the Jar lid by any other items such as a towel, paper cups, dishes etc. as it could lead to injury or damage to the
appliance.
SPATULA
• The spatula is used to scrape the food and liquids from inside the jar.
• Do not use any other utensil as they may cause damage to the inside surface of the jar.
• Only use the spatula when the appliance is turned off and the Jar Lid removed.
STRAINER BASKET g.16
• The Strainer / Steamer Basket can be used to strain out fruit / vegetable juice after processing.
• Insert the Strainer into the jar and hold in place while you pour out the juice.
• It can also be used to hold soft food such as pasta or noodles while cooking, and can be used to cook side dishes, such as rice and potatoes.
STEAMER ASSEMBLY FIG.17
• The Steamer accessory is used for steaming vegetables, sh, and any other food items that you prefer to be steamed.
• To set up the Steamer, the Jar Lid needs to be tted to the Jar and lock on, then the Measuring Cup needs to be removed.
• The Steamer is then placed on top of the Jar Lid ensuring it seats properly.
• Please make sure that the steamer is covered properly with the Steamer Lid before heating and steaming.
• NOTE: The steamer components cannot be used in a microwave oven or in / on any other electrical appliance.
• Do Not touch any part of the steamer, other than the handles, when in use as you may be burnt.
• Keep well clear of the steam vent holes in the steamer lid to avoid injury by hot steam.
• Do Not cover or block the holes in the steamer lid as the steam will nd another escape path and may cause serious injury or damage to
surrounding items.
INSTRUCTIONS FOR USE
• NOTE: When rst using the Thermo Cooker, you may notice an electrical smell from the motor which is quite normal. After a period of use, this
smell will gradually disappear.
• IMPORTANT: Before use, READ ALL the notes under the headings “Important Safeguards” and “Methods of Safe Installation”.
• Failure to read and understand the safe operation and installation of this appliance may cause serious Injury.
ON/OFF SWITCH g.18
• The switch is on the back of appliance. Use this switch to switch the appliance on or off.
• The TFT touch screen will turn on and illuminate with the start-up screen.
fig.15 fig.16
fig.17
fig.18

10
• NOTE: No functions will work unless the Jar is installed and the lid tted and locked. Except for the Scale Function and Heating Function.
• When the jar lid is not tted, heating can be started, but the motor cannot start working until the jar lid is tted and locked in position.
TOUCH SCREEN DISPLAY
WI-FI CONNECTION
• 1. Once the appliance has started up, the home screen will display and a notication will appear that states “Wi-Fi is not connected, please go to
setting to connect Wi-Fi”.
• NOTE: To gain access to the cloud recipes, the appliance must be connected to an active Wi-Fi connection.
• 2. Select the “Connect to Wi-Fi” option which will display the list of active Wi-Fi connections.
• 3. Select your active Wi-Fi connection and enter your password.
• Note: If the Wi-Fi connection doesn’t display in the list, ensure that the connection is not 5G or is a network with WEP, as its not supported.
• 4. Once you have connected your appliance to the Wi-Fi, you can start to explore the different pages located on the TFT display.
TFT DISPLAY OVERVIEW
CLOUD RECIPE
• The Cloud Recipe section is located on the home screen or at the bottom menu bar which displays the cloud recipes list.
• 1. Press the Cloud Recipe the following categories will display once you have selected cloud recipes; beverage, basics, desserts, main dishes,
soup, appetizers and sauces.
• 2. Press one of the category options to begin scrolling through the cloud recipes.
• Once you have selected your category, a line of headings will appear above the recipes. You can ick through the different categories or
alternatively select the “all” option to display all of the recipes at once.
• 3. Once you have selected a recipe, it will display the ingredients list required and show the steps required to make the recipe.
NOTE: There is a search bar located at the top right corner of
the cloud recipes menu, press on it to manually search for a
recipe using the keyboard on the touch screen.
NOTE: Only when your phone is connected with the Thermo
Cooker, cloud recipes time will show on the screen( refer to
“Link My App” section ).
NOTE: The time to load the cloud recipes will depend on the
speed of your internet connection.