Basalte 092-01 User manual

Installation Manual
© 2015 basalte v1.0
Flush mount for Sentido
Description
The flush mount for Sentido (092-01) is an adapter for in-wall flush installation of a
Sentido keypad. Enzo finishes are not compatible.
The flush mount for Sentido securely mounts the keypad while allowing easy access,
insertion and exertion. The adapter is supplied unpainted. The flush mount is designed
to be installed in a drywall. For installation in concrete/brickwall, first install an
appropriate box for flush mount in concrete wall. (092-11 not included)
Parts list
1. Wall adapter
2. Sentido adapter
3. (2x) M2 nut
4. (2x) M3 screw
Compatible products
B. Sentido cover (201-xx or 202-xx) not included
A. Sentido (200-xx) not included
Flush mount for Sentido
Model No. 092-01
(keypad not included)
Safety instructions
• Turn o the power in areas where you will be drilling to avoid electric shock.
• Treatments such as sanding, drilling, painting, etc. may generate hazardous dust and/or fumes. Work in
well ventilated areas. Use suitable personal protective equipment (dust mask, goggles) as necessary.
Remove keypad
Key properties
• Dimensions (W/H/D) : 141mm (5.6")/141mm (5.6")/22mm
• Weight: 0.19kg (0.42lbs.)
PUSH TO RELEASE
drywall thickness 12,7 (0.5")
22 (0.87")
141 (5.6")
141 (5.6")
102 (4.0")
between drywall channels
100,9 (4.0")
between drywall channels
magnets holding the Sentido adapter
1324
AB
magnets holding the Sentido adapter
FRONT SIDE REAR
FRONT

Installation Manual
© 2015 basalte v1.0
Flush mount for Sentido
basalte bvba | hundelgemsesteenweg 1A | 9820 merelbeke | belgium
t [phone] | f [phone] | www.basalte.be | [email protected]
Step 2 – Mud and tape (fig 3.)
• Ensure that the front surface of the mount is aligned with the drywall and that all of the screws are flush with the
surface of the drywall.
• Before applying tape, fill gaps with setting-type compound.
• Perform standard mud and tape drywall joining procedure.
• Do not apply drywall compound to front surface. Apply drywall compound to external groove only.
• Sand excess drywall compound to reveille front wall mount surface.
Step 3 – Painting (fig 4.)
• Do not paint internal surfaces!
• Paint and painting procedure are in the same manner as drywall painting.
• Paint the number of coats necessary to achieve the desired coverage and texture.
• Good practice: in case of any finish imperfections found around the installed wall mount
(aer paint), you may apply some acrylic wall putty aerwards, gently sand and paint again.
Step 1 – Cut and place (fig 1. & 2.)
• Determine where the flush mount will be located.
• Flush mount needs to fit between two studs.
• Route adequate cabling to the installation point (in accordance with your local electric regulations).
• Flush mount needs to fit between two studs and be installed on two horizontal supports secured to the studs.
• Fix the wall adapter through the holes located on its perimeter using #6 bugle head screws (not included). Make sure to position
the wall adapter as shown on figure 1.
Good practice: apply construction adhesive between wall mount and supports.
• Cut appropriate drywall pieces and plug voids on the mount sides.
• Secure all drywall edges to the studs and the horizontal supports.
fig 1. fig 3.fig 2. fig 4.
horizontal
support
studs
tape
external groove
front wall
mount surface
do not paint
internal surfaces