BCP SKY6358 User manual

SKY6358
Ver. 1
INSTRUCTION
MANUAL
Set of 4 Infrared Laser Tag
Blasters & Vests

As shoppers, we’re always trying
to find the perfect balance between
quality & value. At BCP, we believe
we’ve achieved that. Our diverse
catalog of everyday essentials is
tailored especially to our customers
& guaranteed to hit that sweet
spot of high quality & low price.
Always.

|3
• LIFE INDICATORS (3): Each life indicator represents 3 health (for a total of 9).
• LOW BATTERY: The 3 life indicators will flash slowly to indicate that the blaster has low battery.
• MAX STRIKE DISTANCE: 40 meter
PHILLIPS
SCREWDRIVER
REQUIRED
BLASTER DIAGRAM
3 AAA BATTERIES
PER VEST
+AAA -
3 AAA BATTERIES
PER BLASTER
+AAA -
Please retain these instructions for future reference.
NOTICE
•Avoid exposure to direct sunlight and excessive heat.
•Do not immerse product in water.
•Do not alter this product in any way as it may result in personal injury, product failure, and
property damage.
•If any parts are missing, broken, damaged, or worn, stop using this product until repairs are made
and/or factory replacement parts are installed.
•Do not use this item in a way inconsistent with manufacturer’s instructions as this could void the
product warranty.
TEAM
SELECTION
TEAM INDICATORS
LIFE INDICATORS (3)
TRIGGER
RELOADER
INFRARED
RECEIVER
INFRARED
EMISSION
FIRE-TYPE
SELECTION
POWER SWITCH
UP TO 5 MIN.
ASSEMBLY
1 PERSON
ASSEMBLY
8 YEARS
OLD AND UP
8+

1. Use a screwdriver to remove the battery covers.
2. Insert 3 AAA batteries into the blasters and 3 AAA batteries into the vests. Make sure the batteries are
inserted with the correct polarity.
3. Replace & secure battery covers.
4|
VEST DIAGRAM
• INFRARED RECEIVER: Vibrates and flashes colors when hit
• LIGHT INDICATOR: Displays team color
• LIFE INDICATORS (4): Each life indicator represents 3 health (for a total of 12)
NOTE: When vest and gun are paired, only the health points of the vest are active (12 health points).
BATTERY INSTALLATION - BLASTER & VEST
BLASTER VEST
LIGHT INDICATOR / INFRARED RECEIVER
LIFE INDICATORS (4) BATTERY COVER
POWER SWITCH

|5
1. Place vest strap over your neck.
2. Fasten the buckle in the back. Tighten the straps until secure.
VEST INSTRUCTIONS
Press the Fire-Type Selection button to toggle between four firing modes:
4
Press the team selection button to toggle between teams. There are 4 colors to represent possible
teams—Blue, red, yellow, and white. You cannot fire upon your own team. A player cannot change
teams during a game.
2
Switch the vest on and it will cycle through dierent colors. Use the blaster to shoot the vest and
turn the color of your team. The vest is now assigned to your team. The blaster and vest will flash
slowly, the infrared receivers are now synchronized and share health points (12 points total).
3
Switch the blaster on. The blaster will default to pistol mode.
1
OPERATING INSTRUCTIONS
Laser Gun Machine Gun Plasma Gun
Single Shot
HEALTH REDUCED
BY EACH SHOT
FIRING MODES
SHOTS
When you run out of ammo, press the reload button under the grip to reload.
FRONT BACK

RESET BLASTER & VEST
•A player cannot change teams or reset a blaster/vest during a game.
•Press the team selection button to change your team before a game.
•To reset a blaster/vest, switch the blaster/vest o and on again.
6|
OPERATING INSTRUCTIONS
Aim and fire at an opponent’s blaster or vest to register a hit. Once hit, the life indicator will reduce
accordingly and the blaster/vest will vibrate and emit a sound. Each life indicator will show a
dierent level of health:
•1 health point lost = Life indicator flashes slowly.
•2 health points lost = Life indicator flashes quickly.
•3 Health points lost = Life indicator will be dark.
When all life indicators reach 0, the indicator will be dark and you will be unable to fire anymore.
5
TEAM A
REASON
Low battery
Infrared signal could not reach the
blaster because the distance is too far
or angle is wrong
Obstacles blocking the infrared signal
Low battery
Overexposure to direct sunlight
Competing infrared transmission from
other devices, such as TV remotes
TROUBLESHOOTING
PROBLEM
Blasters do not work
Blasters operate
automatically
SOLUTION
Replace the batteries
Reduce the firing distance and firing angle
Remove the obstacles
Replace the batteries
Block sunlight or play in an area
without direct sunlight
Stop using or move away from
competing infrared devices
NOTE: If normal operation of the product is disturbed or interrupted, strong electro-magnetic interference
may be causing a problem. Reset the product by turning it completely o and then back on. If normal
operation does not resume, try replacing the batteries and moving the product to another location.
TEAM A
TEAM A TEAM B
TEAM B
TEAM B

|7
WARNINGS REGARDING BATTERIES
•Do not mix alkaline, standard (carbon zinc) and rechargeable (nickel hydride) batteries.
•Do not mix old and new batteries.
•Non-rechargeable batteries should not be charged.
•Rechargeable batteries should be charged under adult supervision only.
•Exhausted batteries should be removed.
•The supply terminals should not be short-circuited.
•Do not put batteries next to or in a heat source (fire, electronic heating device, etc.).
•Do not hit batteries against hard objects.
•Do not submerge batteries in water.
•Batteries should be inserted with the correct polarity.
MAINTENANCE & REPAIR
•If this item will not be used for an extended period, remove all batteries to prevent degradation
and damage.
•Clean o dust with a dry cloth.
•Do not leave this product exposed to excessive heat or sunlight.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
This product may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Any changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Responsible party (contact for FCC matters only):
Quality Control Dept.
15101 Red Hill Ave.
Tustin, CA 92780
FCC COMPLIANCE STATEMENT

All items can be returned for any reason within 60 days of the receipt and will receive a full refund as long
as the item is returned in its original product packaging and all accessories from its original shipment are
included. All returned items will receive a full refund back to the original payment method. All returned
items will not be charged a re-stocking fee.
All returned items require an RA (Return Authorization) number, which can only be provided by a Best
Choice Products Customer Service Representative when the return request is submitted. Items received
without an RA may not be accepted or may increase your return processing time. Once an item has been
received by Best Choice Products, refunds or replacements will be processed within 5 business days.
All returns must be shipped back to the Best Choice Products Return Center at the customer’s expense. If
the reason for return is a result of an error by Best Choice Products then Best Choice Products will provide
a pre-paid shipping label via email. Boxes for return shipping will not be provided by Best Choice Products,
and is the customer’s responsibility to either use the original shipping boxes or purchase new boxes.
Pictures may be required for some returns to ensure an item is not damaged prior to its return. Items
returned are not considered undamaged until they are received by Best Choice Products and verified as
such. All damages to items are the customer’s responsibility until the item has been received by and
acknowledge by Best Choice Products as undamaged.
PRODUCT WARRANTY INFORMATION
Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or
loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use,
inadequate maintenance, unapproved modification, or neglect of this product.
HELP CENTER
Product Assembly
Product InquiryChat Support Returns & Refunds
Orders FAQ
WARNING
Question about your product? We're here to help. Visit us at:
help.bestchoiceproducts.com
CHAT
US!