AGame 166826 User manual

Style #166826
16 Ft Mega Trampoline and Enclosure
Customer Service: [phone]
7:00 am to 12:00 am CST (daily)
Live Chat at: www.academy.com
Email: [e-mail]
(Made in China)
Please keep this instruction manual for future reference
Assembly Instructions
&User’s Manual
Version 2.4

Page 2 of 30
Table of Contents
Warnings
Tools and Parts
Assembly Instructions
Care and Maintenance
Warranty Information
3
11
14
29
30
Note: Before beginning assembly of product, make sure
all parts are present. Compare parts with package content
list and hardware contents. If any part is missing or
damaged, do not attempt to assemble the unit. Contact
customer service for replacement parts.

WARNINGS
Page 3 of 30

WARNINGS
Page 4 of 30

Page 5 of 30

Page 6 of 30
ATTACH TO ENCLOSURE MESH AT DOOR
Page 6 of 30

Page 7 of 30

Page 8 of 30

Page 9 of 30

Page 10 of 30

7.5” length spring
Stitched mat with 98 V Rings
Description:
Safety glasses
Description:
Cross-head screwdriver
Description:
Mallet
Description:
Gloves
Tools Required
Page 11 of 30

Top enclosure poles
(Foam Sleeves and
Enclosure Cap Pre-inserted)
Bottom enclosure poles
(Foam Sleeves Pre-inserted)
Cord
NOTICE: Please review part list and confirm all parts are included. If any parts are dam-
aged or missing, please contact customer service at (888)-922-2336 for replacement. (See
front cover) for replacements. Do not attempt assembly.
Page 12 of 30

NOTICE: Determine the final setup location for the trampoline before
assembly. Assemble the trampoline in the desired area to prevent
unnecessary movement during or after the completed assembly.
Moving the trampoline during or after assembly may cause
damages to the trampoline frame.
If it is necessary to move the trampoline, always do so with 2+
people, keep horizontal, and lift slightly.
STOP!
Page 13 of 30

Notice:Must wear gloves and protective
eyewear during assembly.
First you will complete one of the six
sections of the trampoline frame.
Insert the narrow end of the top tube
with T-connector A into T-connector B.
Note: Use mallet to ensure connectors
are fully assembled to the top rail, if
needed.
Assembly Instructions
Step 1:
Step 2:
You will need the following parts
7 x Top Tubes with T-Connector A –Part A
7 x Top Tubes with T-Connector B –Part B
14 x Leg Extensions–Part C
7 x Leg Centers–Part D
Page 14 of 30

Assembly Instructions
Step 3:
Step 4:
Insert the two leg extensions onto
one leg center.
Insert one of the leg extensions of
completed assembly into T-Connector
(A).
Page 15 of 30

Assembly Instructions
Step 5:
Step 6:
IMPORTANT: The frame is held together
under tension so you will have to use
some force to insert certain parts.
Secure top tube using your feet and grip
other end of the leg extension with both
hands.
Pull the extension until it is aligned with the
T-Connector B (motion 1).
Once aligned, slide the leg extension end
into T-Connector B (motion 2).
Grip the leg shaft and push down to fully
insert the leg extension into the T-Connector
A.
Grip the leg shaft and push down to fully
insert the leg extension into the T-Connector
B.
NOTICE: Use rubber mallet, if needed, to
ensure legs are fully inserted into T-Connec-
tors A and B.
You have now completed the first frame
section.
Repeat the previous five steps until you
have assembled all 7 frame sections.
Page 16 of 30

Assembly Instructions
Step 7:
Step 8:
This step will require 2 people who
must be wearing gloves and protective
eyewear.
Connect two of the frame sections
together as shown in the diagram.
You will now need to complete frame
connection. This will take some force.
The easiest method is if the two people
face each other.
Hold the top tubes on either side of the
T-Connectors and push towards each
other until the loose end of the frame
can be inserted into the T-Connector.
IMPORTANT: Ensureall of the top tubes,
leg extensions, and center legs are fully
inserted.
The frame is now fully assembled.
While one person holds the assembled
sections upright, the other person can
connect a third section onto the end of
the assembled sections.
Repeat for remaining four sections.
Page 17 of 30
STOP: Is the trampoline in the desired
location? Please ensure your frame is
placed at the final desired location before
proceeding to step 9. Any movement
during or after step 9 may result in
damage to your trampoline frame.

Step 9:
Step 10:
Assembly Instructions
Yellow stitched
V-ring
Page 18 of 30
IMPORTANT: Identify the closed end
of the spring and the open end of the
spring for proper assembly.
IMPORTANT: Springs must be
inserted in the correct direction. The
closed end will attach to the stitched
mat and open end to the frame.
Ensure all the springs are fully
inserted into the slots on top of the
frame.
Closed
End Open
End
WARNING : Wear protective eyewear
and gloves during the assembly of the
stitched mat.
Layout the stitched mat (with the
V-Rings) part E inside the frame of the
trampoline with the warning labels
facing upwards.
Locate the 7 V-Rings with yellow stitch-
ing. These will be at 51.4 degrees to
each other.
Tip: There are 13 V-Rings in between
each yellow stitched V-Ring.

Assembly Instructions
Step 11:
1to 7 Springs
Instructions
Insert the Closed end of one spring Part F, onto one of the webbings yellow stitched V-Rings as
shown.
IMPORTANT: Correct Spring direction must be utilized to ensure a secure attachment as shown
in step 10.
Insert the Open end of the spring into corresponding spring slot (location 1) in the top of the
frame. See step 11
Using spring pulling tool (part G) to place 1 spring between each yellow stitched V-ring connector
to the middle of every other top rail section, following the sequence indicted above.
Hook the spring tool onto the end of the spring and pull until the spring can be inserted into the
spring slot on the top of the frame.
IMPORTANT:Springs must be inserted in the correct direction. The closed end will secure to the
mat and open end to the frame. Ensure all of the springs are fully inserted into the slots on top of
the frame.
Page 19 of 30
1
2
3
4
5
6
7
Yellow stitching
webbing

Assembly Instructions
Step 12:
8to 14 Springs
Instructions
IMPORTANT: It is important to follow the number sequence accordingly to prevent over-
stretching the springs.
Notice: Next set of 7 springs will be centered between previously attached springs, per
sequence shown above.
Using spring pulling tool (part G) complete the next 7 springs using the sequence shown
above.
Following the sequence indicated in steps 13 through 24. Attach the remaining springs.
8
Page 20 of 30
9
10
11
12
14
13