Beagle Parsec's Beagle User manual

BEAGLE
Installation and Operation Manual
Parsec’s Beagle is a low prole ve-in-one MIMO LTE, MIMO Wi-
Fi, and GNSS external waterproof antenna. is rugged low-prole
omni-directional antenna works on most of the common European
LTE bands with high eciency. e Beagle is optimized for LTE
isolation.
REQUIRED TOOLS
REQUIRED ACCESSORIES
Phillips Screwdriver
9” Zip Ties
Scissors
Ethernet Cords: 2pc (Length as required by the customer)(Not required for A version)
Battery: PowerAdd Pilot Pro 2 2300mAH Portable Battery Charger
USB Cords: 1pc (Length as required by customer)
Cradlepoint 2x2 Power to Barrel Adapter
Router (select one of the following routers.)
• CRADLEPOINT IBR900-1200M
• CRADLEPOINT IBR600

FIGURE 1
FIGURE 3 FIGURE 4
FIGURE 2
Step 1.
Step 2.
Step 3.
Step 4.
Insert the PowerADD battery into the battery tray. (Figure 1)
Place the top cover plate on the battery tray and fasten the battery tray to the top cover plate using nine 4-40 at
head screw provided in the kit. (Figure 2)
Place the router on the top cover plate and align the mount holes of the router with the mounting holes on the top
cover plate. (Figure 3)
Using four 6-32 at head screws provided in the kit mount the router on the cover plate. (Figure 4)
Battery and Router Installation:

Step 1.
Step 2.
Step 3.
Step 4.
Thread the antenna cables through the cover plate. Connect the antenna cables to the router as shown in the table.
(Figure 5)
Connect the USB connector of the fan to the USB port on the Router.
Connect the two ethernet cords from the LAN and WAN on the router to the RJ-45 adapters on the antenna enclosure.
Connect one barrel connector of the switch to the battery and the other to the 2x2 power to barrel adapter.
FIGURE 5
Connection Instructions:
Step 6.
Set the battery to supply 12V by pressing and holding the power button for 5 seconds until you see the volts on the
screen. Press the button again to set it to 12V. (Figure 5 & 6)
FIGURE 6FIGURE 5

Step 6.
Place the top cover plate on the enclosure and fasten it to the enclosure using the 14 thread forming screws provided
in the kit. (Figure 7 & 8)
FIGURE 7 FIGURE 8
Cables Correctly Installed
Step 5.
Connect the 4 pin connector of the barrel adapter to the power port on the router.
FIGURE 6 (STEPS 6-9)

Antenna Operation:
Step 1.
Step 2.
Step 3.
Open the Beagle antenna enclosure and check the battery level on the LCD screen. Make sure the power switch is OFF.
If the battery level is lower than 25% plug in the battery charger and charge the battery until it is at 100%. (Figure 9 & 10)
Open the fan caps on the left and right side of the antenna enclosure (Figure 11 & 12). Make sure that the antenna is
away from the location subjected to any liquid splashing, especially when the caps are open.
Turn ON the power switch – the blue light on the switch will turn ON. Wait for two minutes or untll you hear the fan
running. (Figure 13)
FIGURE 9
FIGURE 11 FIGURE 12
FIGURE 13
FIGURE 10

Step 4.
Step 5.
Step 6.
Connect a network cable between the ethernet ports on a computer and one of the ethernet ports on the antenna
enclosure. Make sure you are connected to a LAN port and not a WAN port.
Bring up a web browser on the computer and type 192.168.0.1 into the address bar. You should see the Cradlepoint login.
(Figure 14
Type the username and password. Username is “admin” by default. The password can be found on the information
cutout on the router. (Figure 15
FIGURE 14
FIGURE 15

parsec-t.com
CAUTION
To comply with FCC RF Exposure requirements in section 1.1310
of the FCC Rules, antennas used with this device must be installed
to provide a separation distance of at least 20 cm from all persons to
satisfy RF exposure compliance.
DO NOT
- Operate the transmitter when someone is within 24 inches of
the antenna.
- Install antenna or mast assembly on a windy day
- Install the mast close to power lines as it can cause serious injuries
or death.
WARNING
is document gives the detailed instructions to install an antenna to
the best of our knowledge. is document if for general information
only. It cannot be used as a warranty. Parsec Technologies, Inc. will
not accept any liability for any damage caused by an antenna due to
unknown variables.
Make sure the fan cap covers are open while using the antenna.
Install the sim in router before mounting on to the router mount plate.
Warnings:
Step 7.
Step 8.
In the router, click on Status, Internet, and then Connections in the dropdown menu. You should see options related to
SIM cards installed. Select the option with a cellular SIM. (Figure 19)
If all of the steps are completed, the antenna should be on and operating. Close the top cover plate using the thread
forming screws provided in the kit. (Figure 20)
FIGURE 16
FIGURE 17