Beam Terra 800 User manual

Terra 800
Quick Start Guide
www.beamcommunications.com
PART #: USRQSG006702
BEAM Communications Pty Ltd
8 Anzed Court, Mulgrave
Victoria, 3170, AUSTRALIA
Web: www.beamcommunications.com
Information: [email protected]om
Support: suppor[email protected]
Tel: [phone]
Fax: [phone]
2. SIM Installation
REAR SIM CARD
If your Service Provider has not installed the SIM card for you, follow
these steps to install.
1. Turn the Terminal’s source of power
OFF. Failure to turn it OFF can result in
corruption of your SIM card memory.
2. The Rear SIM is accessed from the rear
of the terminal. Undo the screw and
remove the cover.
3. The SIM connector is shown highlighted
below. Slide the tray guide into the open
position with your nger or thumb.
4. Once opened, raise the SIM tray as shown
below.
5. Gently insert the SIM card into the tray slots
making sure that the golden contacts are
facing downwards.
6. Lower the tray and slide the tray guide into
the lock position.
7. Replace the SIM cover, and tighten the
screw.
SIDE SIM CARD
The Side SIM port can be used on its own, or in addition to the rear port.
1. Insert the SIM with gold contacts
facing down
2. Close the SIM door, and ensure that it
“clicks” shut. This indicates the water
resistant seal has been engaged.
3. Power the terminal back ON.
4. The SIM will automatically register on
the SIM service of the Side SIM.
NOTE
Gold contacts on SIM must be facing downwards.
The Side SIM Port only accepts full size SIM. If required, you can ret your SIM
to the outer card using adhesive tape as illustrated below:
1. Terra 800 Equipment Overview
1. Interchangeable mounting cup
(spring or springless)
2. Privacy handset
3. Speaker
4. Microphone
5. Status LED
6. Screen display
7. Dial keypad
8. Side SIM card port
(full size rapid user)
9. Function keypad
10. Mini USB port
11. Back panel connectors
a. RJ9 privacy handset
b. RJ11/POTS interface
c. Auxiliary device port
d. DC power and accessory input
e. Ring alert / audio system mute
1
2
3
4
6
7
8
9
10
5
11
abe
c d
3.
4.
5.

3. Access to rear connector bay
For the Terra 800, the external cable interfaces
are at the rear of the terminal. The cover
panel creates the IP54 rating for the electrical
interface and retains the cables in their
respective channels. The cover panel is fixed in
place by 6 screws.
a. RJ9 Privacy Handset
b. RJ11/POTS Interface
c. Auxiliary Port
d. DC power and accessory input
e. Ring alert / audio system mute
4. Antenna Connection
1. Refer to the antennas installation guide for antenna
mounting and location requirements.
2. Connect the antenna cable labelled “GPS” to the
SMA antenna connector labelled “GPS”.
3. Connect the antenna cable labelled “Inmarsat” to the
SMA antenna connector labelled “ISAT”.
4. Connect the GPS-SMA (F) cable end to the Terra 800
SMA connector
5. Connect the TNC (F) antenna cable end to the Terra
800 satellite connector.
7. Terra 800 Dial Keypad
9. Terra 800 Function Keys
Location Button Mode Action LED/Sound
Mute Press
on/o
In a Call:
Mute the microphone (uplink) on the privacy
handset.
LED turns RED - Muted
LED turns OFF - Not muted
LED ashing Yellow - RJ11/POTS in use
OR Up/Down
In a Call:
Increase/decrease volume on speakerphone or
privacy handset.
Audio will sound louder/quieter with each press.
Out of Call:
Increase/decrease volume of incoming ring
tone on the speakerphone.
A beep will sound indicating the increased/decreased ring tone volume
+
Brightness
dual button
simultaneous
press
(1 second)
Out of Call:
Enter LED brightness change mode. Press UP
and DOWN arrows to vary intensity. Mode will
automatically exit after 5 seconds after the last
button press.
All LED’s will change to WHITE and a single beep will sound when
entering brightness change mode.
A short double beep will sound when exiting change mode.
Speakerphone
press ON/OFF
In a Call:
Terminate call if speakerphone mode is active
Activate speakerphone mode if Privacy Handset
mode is active.
LED turns GREEN - Speakerphone mode active
LED turns OFF - Speakerphone mode not active
Out of Call:
Answer inbound call in speakerphone mode
54
32
TNC
SMA
SMA
SMA
Satellite
Antenna
Cable
GPS
Antenna
Cable
THIS SIDE UP
abe
cd
8.Status LED
The Status LED indicates the terminal registration
state or any error conditions:
Special Modes of Operation
Firmware Upgrade Mode
• In rmware upgrade mode STATUS LED will
turn solid YELLOW. All other LEDs will be o.
Entering this mode will be accompanied by
a long beep followed by three short beeps.
Transceiver (USB Bridge) Mode
• In this mode all LED’s will ash GREEN.
RED YELLOW GREEN
ILLUMINATED • No signal
• Not registered
• No SIM card
DTR present on data
port
Unit registered and can
place a call.
FLASHING Firmware upgrade mode
active
Data call in progress Call in progress OR
Transceiver Upgrade Mode
ALTERNATING Red/Yellow - Short circuit on SAT antenna input
Red/Green - Short circuit on GPS antenna input
Red/Yellow/Green - Internal communications error
Yellow/Green - Short on Ring Alert/audio system mute output*
* NOTE: The Red or Black wire of the “ring alert/audio system mute” wrongly connected to positive supply
voltage input could cause over-current condition. The output will be automatically disabled when this
condition is detected, and an error written to the log.
Signal strength
Network
Status bar
Screen
Local time
Navigation keys
Centre selection key
Right selection key
Green key
Left selection key
Red key
Product name
ContactsInfoMenu
Terra 800
Inmarsat 05:56
5. Wall Mounting & Locking Bolt
There are eight (8) xing holes available
for mounting the bracket to a wall. It is
recommended that at least 3 screws are used
to ensure the Terminal is mounted securely.
1
Slide the terminal down to “lock”
Fit the three (3) hooks on the mount
bracket into the three (3) large mounting
holes on the back of the terminal
Final “lock” position
2
3
WARNING
DO NOT pull with force on the cables from the rear of
the Terra 800. Please install strain relief clamping for
the antenna cables where required.
Correct installation of the antenna system is a
vital part of the Terra 800 system, to ensure reliable
functionality, and drop-free calls.
WARNING
Changes or modications not expressly approved
by Beam Communications could void the product
warranty.
WARNING
To satisfy FCC RF exposure requirements for mobile
transmitting devices, a separation distance of 55cm
or more should be maintained between the antenna
of this device and persons during device operation.
To ensure compliance, operations at closer than this
distance is not recommended.
Mounting cups
There are two unique mounting cups for
the privacy handset. (1) springless cup for
either a desk mounted position or a wall
mounted position. (2) spring cup for rough
environments.
Changing cups
1. Unhook the privacy handset from
cup.
2. Use a at screw driver in one of the
two side slots to leaver the cup cover
out exposing the 3 screws.
3. Unscrew 3 screws with a phillips
screwdriver.
4. Detach the cup and replace with the
spring or springless cup.
NOTE
When the cup is removed this will expose the
locking bolt screw hole.
(1) Springless cup
The ‘springless’ cup is used for normal to light-
use desk mounted cradle position.
Wall mounted cradle position.
The mounting clip can be slid out and
reversed, revealing a protruding edge that
the privacy handset rests upon. For a wall
mounted terminal this retains the privacy
handset while allowing the handset to be
easily removed when in a call.
(2) Spring cup - heavy duty use cup
In harsh environments, the privacy handset
is actively retained in the mounting cup.
This is achieved by using the ‘spring’
mounting cup. To remove the handset from
the cup, the phone is lifted up against the
pressure of the spring until it clears the
lower protruding edge and can be removed
from the terminal.
6. Changing Cups
1
2
3
4
Locking Bolt Installation
1. Remove the mounting cup
(See MANUAL for details)
2. Insert the bolt into the hole beneath the cup
and screw into place
3. Ensure the Terminal will not slide up o the
mounting bracket
4. Replace the mounting cup.
Keypad locked
Alarm set
Call divert on
Unread message
USB connection
New voicemail
Missed call
Bluetooth on
Keypad locked
Alarm set
Call divert on
Unread message
USB connection
New voicemail
Missed call
Bluetooth on