Beast Hover-1 hy-x10 User manual

OPERATION MANUAL

HY-X10

ELECTRIC SCOOTER

WITH BLUETOOTH SPEAKER

BEAST

HELMETS

SAVE

LIVES!

Always wear a properly tted helmet that

complies with CPSC or CE safety standards

when you ride your bicycle.

Correct Fitting:

Make sure your helmet

covers your forehead.

Incorrect Fitting:

Forehead is exposed

and vulnerable to

serious injury.

PLEASE READ THE USER MANUAL THOROUGHLY.

Failure to follow the basic instructions and safety precautions listed in

the user manual can lead to damage to your device, other property

damage, serious bodily injury, and even death.

Thank you for purchasing the Hover-1 Beast Electric Scooter. Please

read all instructions carefully before using and retain this manual for

future use and reference.

This manual applies to the Hover-1 Beast Scooter.

• In order to avoid dangers that are caused by collisions, falls, and loss

of control, please learn how to ride the Hover-1 Beast safely.

• You can learn operating skills by reading the product manual and

watching videos.

• This manual includes all operating instructions and precautions, and

users must read it carefully and follow the instructions.

• Hover-1 can not be held liable for damage or injury caused by

failure to understand and follow the warnings and instructions in this

manual.

ATTENTION

1. Use only the supplied charger with this scooter.

Charger Manufacturer: Jin Xin Yu Power (Shenzhen) Supply Co., Ltd.

Model: XVE-4200150

2. The operating temperature range of the charger is 50° F-77° F

(10-25° C).

3. The operating temperature range of the Hover-1 Beast is 32-113° F

(0-45° C).

4. Do not ride on icy or slippery surfaces.

5. Read the user manual and warning labels before riding.

6. Store the Hover-1 Beast in a dry, ventilated environment.

7. When transporting the Hover-1 Beast, avoid violent crashes or

impact.

• Do not operate, or allow others to operate, the Hover-1, until the

user understands all instructions, warnings and safety features

described in this manual.

• Check with your doctor if you have a medical condition that could

affect your ability to use the Hover-1 Beast.

• Persons with head, back or neck ailments or prior surgeries to

those areas of the body are not recommended to use this Hover-1

Beast.

• Do not operate if you are pregnant, have a heart condition, or

have both.

• Persons with any mental or physical conditions that may make

them susceptible to injury or impair their physical or mental

capabilities to recognize, understand and perform all of the

safety instructions and to be able to assume the hazards inherent

in unit use, should not use the Hover-1 Beast.

In this manual, the above symbol with the word “NOTES” indicates

instructions or relevant facts the user should remember prior to using

the device.

In this manual, the above symbol with the word “CAUTION” indicates

a hazardous situation which, if not avoided, can cause minor or

moderate injury.

In this manual, the above symbol with the word “WARNING”

indicates a hazardous situation which, if not avoided, can cause

death or serious injury.

Please keep the serial number on file for warranty claims as well as

proof of purchase.

WARNING!

LOW TEMPERATURE WARNING

Low temperature will affect the lubrication of moving parts inside

the Hover-1 Beast scooter, increasing internal resistance. At the

same time, in low temperatures, the discharge capacity and the

capacity itself of the battery will be significantly decreased.

Use caution when riding the Hover-1 Beast in cold temperatures

(below 40 degrees F).

Doing so may increase the risk of mechanical failures of the

scooter, which may lead to damage to your device, other

property damage, serious bodily injury and even death.

SAFETY INSTRUCTIONS

• Keep the device away from heat sources, direct sunlight,

humidity, water and any other liquids.

• Do not operate the device if it has been exposed to water,

moisture or any other liquids to prevent against electric shock,

explosion and/or injury to yourself and damage to the device.

• Do not use the device if it has been dropped or damaged in

any way.

• Repairs to electrical equipment should only be performed by

the manufacturer. Improper repairs voids the warranty and may

place the user at serious risk.

• Do not puncture or harm the exterior surface of the product in

any way.

• Keep the device free from dust, lint, etc.

• Do not use this device for anything other than its intended use or

purpose. Doing so may damage the device or lead to property

damage, injury or death.

• This product is not a toy. Keep out of reach of children.

• Do not expose batteries, battery pack, or batteries installed to

excessive heat, such as direct sunlight, or open flame.

• Do not allow hands, feet, hair, body parts, clothing or similar

articles to come in contact with moving parts, wheels or drive train,

while the engine is running.

PLEASE READ THE USER MANUAL THOROUGHLY.

Failure to follow the basic instructions and safety precautions listed in

the user manual can lead to damage to your device, other property

damage, serious bodily injury, and even death.

Thank you for purchasing the Hover-1 Beast Electric Scooter. Please

read all instructions carefully before using and retain this manual for

future use and reference.

This manual applies to the Hover-1 Beast Scooter.

• In order to avoid dangers that are caused by collisions, falls, and loss

of control, please learn how to ride the Hover-1 Beast safely.

• You can learn operating skills by reading the product manual and

watching videos.

• This manual includes all operating instructions and precautions, and

users must read it carefully and follow the instructions.

• Hover-1 can not be held liable for damage or injury caused by

failure to understand and follow the warnings and instructions in this

manual.

ATTENTION

1. Use only the supplied charger with this scooter.

Charger Manufacturer: Jin Xin Yu Power (Shenzhen) Supply Co., Ltd.

Model: XVE-4200150

2. The operating temperature range of the charger is 50° F-77° F

(10-25° C).

3. The operating temperature range of the Hover-1 Beast is 32-113° F

(0-45° C).

4. Do not ride on icy or slippery surfaces.

5. Read the user manual and warning labels before riding.

6. Store the Hover-1 Beast in a dry, ventilated environment.

7. When transporting the Hover-1 Beast, avoid violent crashes or

impact.

• Do not operate, or allow others to operate, the Hover-1, until the

user understands all instructions, warnings and safety features

described in this manual.

• Check with your doctor if you have a medical condition that could

affect your ability to use the Hover-1 Beast.

• Persons with head, back or neck ailments or prior surgeries to

those areas of the body are not recommended to use this Hover-1

Beast.

• Do not operate if you are pregnant, have a heart condition, or

have both.

• Persons with any mental or physical conditions that may make

them susceptible to injury or impair their physical or mental

capabilities to recognize, understand and perform all of the

safety instructions and to be able to assume the hazards inherent

in unit use, should not use the Hover-1 Beast.

In this manual, the above symbol with the word “NOTES” indicates

instructions or relevant facts the user should remember prior to using

the device.

In this manual, the above symbol with the word “CAUTION” indicates

a hazardous situation which, if not avoided, can cause minor or

moderate injury.

In this manual, the above symbol with the word “WARNING”

indicates a hazardous situation which, if not avoided, can cause

death or serious injury.

Please keep the serial number on file for warranty claims as well as

proof of purchase.

LOW TEMPERATURE WARNING

Low temperature will affect the lubrication of moving parts inside

the Hover-1 Beast scooter, increasing internal resistance. At the

same time, in low temperatures, the discharge capacity and the

capacity itself of the battery will be significantly decreased.

Use caution when riding the Hover-1 Beast in cold temperatures

(below 40 degrees F).

Doing so may increase the risk of mechanical failures of the

scooter, which may lead to damage to your device, other

property damage, serious bodily injury and even death.

SAFETY INSTRUCTIONS

• Keep the device away from heat sources, direct sunlight,

humidity, water and any other liquids.

• Do not operate the device if it has been exposed to water,

moisture or any other liquids to prevent against electric shock,

explosion and/or injury to yourself and damage to the device.

• Do not use the device if it has been dropped or damaged in

any way.

• Repairs to electrical equipment should only be performed by

the manufacturer. Improper repairs voids the warranty and may

place the user at serious risk.

• Do not puncture or harm the exterior surface of the product in

any way.

• Keep the device free from dust, lint, etc.

• Do not use this device for anything other than its intended use or

purpose. Doing so may damage the device or lead to property

damage, injury or death.

• This product is not a toy. Keep out of reach of children.

• Do not expose batteries, battery pack, or batteries installed to

excessive heat, such as direct sunlight, or open flame.

• Do not allow hands, feet, hair, body parts, clothing or similar

articles to come in contact with moving parts, wheels or drive train,

while the engine is running.

PLEASE READ THE USER MANUAL THOROUGHLY.

Failure to follow the basic instructions and safety precautions listed in

the user manual can lead to damage to your device, other property

damage, serious bodily injury, and even death.

Thank you for purchasing the Hover-1 Beast Electric Scooter. Please

read all instructions carefully before using and retain this manual for

future use and reference.

This manual applies to the Hover-1 Beast Scooter.

• In order to avoid dangers that are caused by collisions, falls, and loss

of control, please learn how to ride the Hover-1 Beast safely.

• You can learn operating skills by reading the product manual and

watching videos.

• This manual includes all operating instructions and precautions, and

users must read it carefully and follow the instructions.

• Hover-1 can not be held liable for damage or injury caused by

failure to understand and follow the warnings and instructions in this

manual.

ATTENTION

1. Use only the supplied charger with this scooter.

Charger Manufacturer: Jin Xin Yu Power (Shenzhen) Supply Co., Ltd.

Model: XVE-4200150

2. The operating temperature range of the charger is 50° F-77° F

(10-25° C).

3. The operating temperature range of the Hover-1 Beast is 32-113° F

(0-45° C).

4. Do not ride on icy or slippery surfaces.

5. Read the user manual and warning labels before riding.

6. Store the Hover-1 Beast in a dry, ventilated environment.

7. When transporting the Hover-1 Beast, avoid violent crashes or

impact.

• Do not operate, or allow others to operate, the Hover-1, until the

user understands all instructions, warnings and safety features

described in this manual.

• Check with your doctor if you have a medical condition that could

affect your ability to use the Hover-1 Beast.

• Persons with head, back or neck ailments or prior surgeries to

those areas of the body are not recommended to use this Hover-1

Beast.

• Do not operate if you are pregnant, have a heart condition, or

have both.

• Persons with any mental or physical conditions that may make

them susceptible to injury or impair their physical or mental

capabilities to recognize, understand and perform all of the

safety instructions and to be able to assume the hazards inherent

in unit use, should not use the Hover-1 Beast.

In this manual, the above symbol with the word “NOTES” indicates

instructions or relevant facts the user should remember prior to using

the device.

In this manual, the above symbol with the word “CAUTION” indicates

a hazardous situation which, if not avoided, can cause minor or

moderate injury.

In this manual, the above symbol with the word “WARNING”

indicates a hazardous situation which, if not avoided, can cause

death or serious injury.

Please keep the serial number on file for warranty claims as well as

proof of purchase.

WARNING!

SERIAL NUMBER

CAUTION!

NOTES:

LOW TEMPERATURE WARNING

Low temperature will affect the lubrication of moving parts inside

the Hover-1 Beast scooter, increasing internal resistance. At the

same time, in low temperatures, the discharge capacity and the

capacity itself of the battery will be significantly decreased.

Use caution when riding the Hover-1 Beast in cold temperatures

(below 40 degrees F).

Doing so may increase the risk of mechanical failures of the

scooter, which may lead to damage to your device, other

property damage, serious bodily injury and even death.

SAFETY INSTRUCTIONS

• Keep the device away from heat sources, direct sunlight,

humidity, water and any other liquids.

• Do not operate the device if it has been exposed to water,

moisture or any other liquids to prevent against electric shock,

explosion and/or injury to yourself and damage to the device.

• Do not use the device if it has been dropped or damaged in

any way.

• Repairs to electrical equipment should only be performed by

the manufacturer. Improper repairs voids the warranty and may

place the user at serious risk.

• Do not puncture or harm the exterior surface of the product in

any way.

• Keep the device free from dust, lint, etc.

• Do not use this device for anything other than its intended use or

purpose. Doing so may damage the device or lead to property

damage, injury or death.

• This product is not a toy. Keep out of reach of children.

• Do not expose batteries, battery pack, or batteries installed to

excessive heat, such as direct sunlight, or open flame.

• Do not allow hands, feet, hair, body parts, clothing or similar

articles to come in contact with moving parts, wheels or drive train,

while the engine is running.

OPERATING PRINCIPALS

The device uses digital electronic gyroscopes and acceleration

sensors to control balance and motion, depending on the user's

center of gravity. The device also uses a control system to drive the

motors that are located within the wheels. The device has a built-in

inertia dynamic stabilization system that can help assist with balance

when moving forward and backwards, but not while turning.

TIP – To increase your stability, you must shift your weight in order to

overcome the centrifugal force during turns, especially when

entering a turn at higher speeds.

Model: HY-X10 - Hover-1 Beast

Net Weight: 30 lbs (13.5 kg)

Load: 44-330 lbs (20-150 kg)

Max Speed: Up to 7.45 mph (12 km/h)

Max Distance Range: Up to 11 miles (18 km)

(at 110lbs load)

Max Incline Angle: 20° degrees

Minimum Turning Radius: 0°

Battery Type: Lithium-ion

Battery Voltage: 36 V

Battery Capacity: 4.3 Ah

Power Requirement: AC 100-240V, 50-60 Hz

Wheel Size: 10 Inches (25.4 cm)

Product size: 28x11x12inch (730x280x300mm)

Bluetooth Range: Up to 33ft

Bluetooth Speaker: V4.0 with stereo sound quality

FCC ID: 2AANZX10

BT ID: D036974

The Hover-1 Beast is a personal transporter. Our technology and

production processes are developed with strict testing for each

Hover-1 Beast scooter. Operating the Hover-1 Beast without following

the contents of this manual may lead to damage to your Hover-1

Beast, or bodily injury.

This manual is designed to give you the information you need for the

safe operation and maintenance of your Hover-1 Beast. Please read

it thoroughly before riding your Hover-1 Beast.

PACKAGE CONTENTS

• Hover-1 Beast Electric Scooter

• 3-pin Charge Cable

• Operation Manual

FEATURES/PARTS

1. Fender 7. LED Light

2. Left Foot Mat 8. Power Button

3. Running Indicator 9. Charge Port

4. Battery Indicator 10. Battery Cover

5. Right Foot Mat 11. Wireless Speaker

6. Tire

INTRODUCTION

1 1

7 7

11 10

OPERATING PRINCIPALS

The device uses digital electronic gyroscopes and acceleration

sensors to control balance and motion, depending on the user's

center of gravity. The device also uses a control system to drive the

motors that are located within the wheels. The device has a built-in

inertia dynamic stabilization system that can help assist with balance

when moving forward and backwards, but not while turning.

TIP – To increase your stability, you must shift your weight in order to

overcome the centrifugal force during turns, especially when

entering a turn at higher speeds.

Model: HY-X10 - Hover-1 Beast

Net Weight: 30 lbs (13.5 kg)

Load: 44-330 lbs (20-150 kg)

Max Speed: Up to 7.45 mph (12 km/h)

Max Distance Range: Up to 11 miles (18 km)

(at 110lbs load)

Max Incline Angle: 20° degrees

Minimum Turning Radius: 0°

Battery Type: Lithium-ion

Battery Voltage: 36 V

Battery Capacity: 4.3 Ah

Power Requirement: AC 100-240V, 50-60 Hz

Wheel Size: 10 Inches (25.4 cm)

Product size: 28x11x12inch (730x280x300mm)

Bluetooth Range: Up to 33ft

Bluetooth Speaker: V4.0 with stereo sound quality

FCC ID: 2AANZX10

BT ID: D036974

The Hover-1 Beast is a personal transporter. Our technology and

production processes are developed with strict testing for each

Hover-1 Beast scooter. Operating the Hover-1 Beast without following

the contents of this manual may lead to damage to your Hover-1

Beast, or bodily injury.

This manual is designed to give you the information you need for the

safe operation and maintenance of your Hover-1 Beast. Please read

it thoroughly before riding your Hover-1 Beast.

PACKAGE CONTENTS

• Hover-1 Beast Electric Scooter

• 3-pin Charge Cable

• Operation Manual

FEATURES/PARTS

1. Fender 7. LED Light

2. Left Foot Mat 8. Power Button

3. Running Indicator 9. Charge Port

4. Battery Indicator 10. Battery Cover

5. Right Foot Mat 11. Wireless Speaker

6. Tire

SPECIFICATIONS

WARNING

Any Hover-1 Beast that does not work

properly can cause you to lose control and

fall. Inspect the entire device thoroughly

before every ride, and do not ride it until any

problems have been corrected.

PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY

TURNING YOUR DEVICE ON/OFF

Power On: Take your device out of the box and place it flat on the

floor. Press the power button (located on the rear of your device)

once. Check the LED indicator (located in the center of your device).

The battery indicator light should be lit, indicating the device is

powered on.

Power Off: Press the power button once.

This Model also has self-balance mode: To activate this mode, press

the power button twice when the scooter is on.

MAT SENSOR

There are four sensors under the foot mats on your Hover-1 Beast.

When the user steps off the scooter mats, it will automatically initiate

self-calibration.

When riding the scooter, you must ensure you are stepping on the foot

mats. Do not step or stand on any other area of your scooter.

Do not put items on the foot mats. Doing so will make the Hover-1

Beast turn on, and increase the probability of collision and cause injury

to people, riders, or damage the device.

The Hover-1 Beast may vibrate or spin in one direction, if weight and

pressure are applied to only one foot mat.

BATTERY INDICATOR

The display board is located in the middle of the Hover-1 Beast.

• Green LED light indicates the device is above 50 percent.

• Red LED light indicates the power is down to 10 percent or lower.

When the LED light turns red, please recharge the device.

RUNNING INDICATOR

When the operator triggers the foot mats, the Running Indicator LED

will light up, which means that the system enters the running state.

When the system has an error during operation, the running LED light

will turn red (for more details see SAFETY ALERTS).

CONTROLS AND DISPLAY

The H1 has a powerful built-in wireless speakers so you can play your

music while riding.

PAIRING THE SPEAKER

1. Ensure your H1 is turned off. If it is not, please turn off your Hover-1 first

before pairing.

2. Turn on your H1 and the speakers will “Ping” to announce that it’s

waiting for a Bluetooth®connection. This will indicate your Beast

speaker is now in pairing mode.

3. Place the Beast and the Bluetooth®device to which you would like

to pair it within the operating distance. We recommend keeping the

two devices no further than 3 feet apart during pairing.

4. Ensure Bluetooth®is enabled on your phone or music device. Refer

to manufacturer’s instructions for how to enable Bluetooth®on your

device.

5. Once you have activated Bluetooth®on your device, select the

option “HY-X10” from the list of available Bluetooth®devices.

6. If required, enter the PIN code "000000" and confirm the entry.

7. The Beast will say “Paired” when successfully paired.

8. Please note, pairing mode on the Hover-1 will last for two minutes. If

no devices are paired after two minutes, the H1 speaker will

automatically return to standby mode.

9. If pairing is unsuccessful, turn off the H1 first and re-pair following the

aforementioned steps.

10. If your smart phone is out of range, or the battery is low on your

Hover-1 Beast, your speaker may disconnect from your smart device,

and the Beast will say “Disconnected.” To reconnect, follow the

aforementioned steps, or recharge your scooter.

NOTE: Once you have paired the Beast speaker with a device, the

speaker will remember this device and will pair automatically when

the device’s Bluetooth®is activated and in range. You do not need to

re-pair any previously connected devices.

Your scooter can pair up to two multi-point devices. You can

reconnect a previously paired device without going through the

pairing or PIN process on up to two devices.

LISTENING TO MUSIC

Once the Beast Bluetooth speaker is paired to your device, you can

stream music wirelessly through it. Only one speaker will play music as

the other speaker is strictly for safety alerts from your Hover-1. Select

the track you wish to listen to on your device to listen via the speakers.

All volume and track controls will be made using your music device.

Should you encounter any problems while streaming, please refer to

your device’s user manual.

BLUETOOTH SPEAKER

It is important that you fully understand all elements of your Hover-1

Beast. If these elements are not used correctly, you will not have full

control of your Hover-1 Beast. Before you ride, learn the functions of

the various mechanisms on your scooter.

Practice using these elements of your Hover-1 Beast at slower speeds

in a flat, open area before taking the device out in public areas.

PRE-RIDE CHECKLIST

Ensure that your Hover-1 Beast is in proper working order each and

every time you ride. If a part of the scooter does not function

correctly, please contact our Customer Support Center.

• Ensure the battery is fully charged before riding your scooter.

• Ensure that the screws on the front and back tires are locked firmly

before each ride.

• Please wear all appropriate safety and protective gear as

previously mentioned in the User Manual before operating your

Hover-1 Beast.

• Make sure to wear comfortable clothes and flat closed-toe shoes

when operating your device.

• Please carefully read the User Manual, which will assist in explaining

the basic working principles and provide tips on how to best enjoy

your experience.

BEFORE RIDING

WARNING

Any Hover-1 Beast that does not work

properly can cause you to lose control

and fall. Do not ride a Hover-1 Beast

with a part that is damaged; replace

the damaged part before riding.

The first rule in safe riding is to use common sense.

Different localities and countries have different laws governing riding

on public roads, and you should check with local officials to ensure

you are complying with these laws.

Hover-1 is not liable for tickets or violations given to riders who do not

follow local laws and regulations.

• For your safety, always wear a helmet that meets CPSC or CE safety

standards. In the event of an accident, a helmet can protect you

from serious injury and in some cases, even death.

• Obey all local traffic laws. Obey red and green lights, one-way

streets, stop signs, pedestrian crosswalks, etc.

• Ride with traffic, not against it.

• Ride defensively; expect the unexpected.

• Give pedestrians the right-of-way.

• Do not ride too close to pedestrians and alert them if you intend to

pass them from behind.

• Slow down at all street intersections and look to the left and right

before crossing.

Your Hover-1 Beast is not equipped with reflectors. It is not

recommended that you ride in conditions of low visibility.

SAFETY PRECAUTIONS

WARNING

When you ride in low-visibility conditions

such as fog, dusk, or night, you might be

diicult to see, which could lead to a

collision. In addition to keeping your

headlight on, wear bright, reective

clothing when riding in poor lighting

conditions.

Think about safety when you ride. You can prevent many accidents

if you think about safety. Below is a helpful checklist for Compact

riders.

SAFETY CHECKLIST

• Do not ride above your skill level. Ensure you have had enough

practice with all functions and features of your Hover-1 Beast.

• Do not ride too fast -- with increased speed comes increased risk. If

you are moving at a higher speed, small bumps can turn into large

impacts, leading to a higher risk of injury if an accident occurs.

• Do not ride with pets.

• Before stepping on your Hover-1 Beast, make sure it is placed flat on

level ground, the power is on, and the Running Indicator light is green.

Do not step on if the Running Indicator light is red.

• Do not try to open or modify your Hover-1 Beast. Doing so, voids the

manufacturer warranty and may cause your Hover-1 Beast to fail,

resulting in injury or death.

• Do not use the Hover-1 Beast in a manner that would put people or

property in danger.

• If you and your friend(s) are riding Hover-1 Beasts together, be sure

to keep a safe distance between each other to prevent collisions,

property damage, serious injuries or even death.

• Be sure to keep your feet on the pedals at all times. Moving your

feet off your Hover-1 Beast while driving is dangerous and may cause

the Hover-1 Beast to stop or veer sideways.

• Do not operate the Hover-1 Beast while under the influence of

drugs and/or alcohol.

• Do not operate the Hover-1 Beast when you are restless or sleepy.

• Use your best judgment to keep yourself out of dangerous situations

with your Hover-1 Beast.

• Do not ride your Hover-1 Beast off of curbs, ramps, or attempt to

operate in a skate park, empty pool, or in any way similar to a

skateboard or scooter. The Hover-1 Beast IS NOT A SKATEBOARD.

Misuse of your Hover-1 Beast, voids the manufacturer warranty and may

lead to injury or damage.

• Do not continuously spin in place, it will cause dizziness and increases

risk of injury.

• Do not abuse your Hover-1 Beast, doing so can damage your unit

and cause failure to the operating system leading to injury. Physical

abuse, including dropping your Hover-1 Beast, voids the

manufacturer warranty.

• Do not operate in or near puddles of water, mud, sand, stones, gravel,

debris or near rough and rugged terrain.

• The Hover-1 Beast can be used on paved surfaces that are flat and

even. If you encounter uneven pavement, please lift your Hover-1 Beast

over and past the obstruction.

• Do not ride in inclement weather: snow, rain, hail, sleek, on icy roads or

in extreme heat or cold.

• Bend your knees when riding on bumpy or uneven pavement to

absorb the shock and vibration and help you keep your balance.

• If you are unsure if you can safely ride on a specific terrain, step off and

carry your Hover-1 Beast. ALWAYS BE ON THE SIDE OF CAUTION.

• Do not attempt to ride over bumps or objects greater then ½ in, even

when prepared and bending your knees.

• PAY ATTENTION - look at where you are riding and be conscious of the

road conditions, people, places, property and objects around you.

• Do not operate the Hover-1 Beast in crowded areas.

• Operate your Hover-1 Beast with extreme caution when indoors,

especially around people, property, and narrow spaces.

• Do not operate the Hover-1 Beast while talking, texting, or looking at

your phone.

• Do not ride your Hover-1 Beast where it is not permitted.

• Do not ride your Hover-1 Beast near motor vehicles or on public roads.

• Do not travel up or down steep hills.

• The Hover-1 Beast is intended for use by a single individual, DO NOT

attempt to operate the Hover-1 Beast with two or more people.

• Do not carry anything while riding the Hover-1 Beast.

• Individuals with lack of balance should not attempt to operate the

Hover-1 Beast.

• Pregnant women should not operate the Hover-1 Beast.

• Young children and the elderly should not operate the Hover-1 Beast.

• At higher speeds, always take into consideration longer stopping

distances.

• Do not step forward off of your Hover-1 Beast.

• Do not attempt to jump on or off your Hover-1 Beast.

• Do not attempt any stunts or tricks with your Hover-1 Beast.

• Do not ride the Hover-1 Beast in dark or poorly lit areas.

• Do not ride the Hover-1 Beast near or over potholes, cracks or uneven

pavement or surfaces.

• Do not operate your Hover-1 Beast off-road.

• Keep in mind that you are 4.3 inches (11.43 cm) taller when operating

the Hover-1 Beast. Make sure to go through doorways safely.

• Do not turn sharply, especially at high speeds.

• Do not exceed the maximum or minimum weight limits.

• Do not step on the fenders of the Hover-1 Beast.

• Avoid driving the Hover-1 Beast in unsafe places, including near areas

with flammable gas, steam, liquid, dust, fiber, which could cause fire and

explosion accidents.

• This device is recommended for riders ages 15 and older.

• This shall not be operated to perform racing, stunt riding, or other

maneuvers, which may cause loss of control, or may cause

uncontrolled operator/passenger actions or reactions.

• Before riding, ensure that tires are in good condition and have

sufficient tread remaining.

• Do not operate near swimming pools or other bodies of water.

To reduce the risk of injury, adult supervision is required.

Never use in roadways, near motor vehicles, on or near

steep inclines or steps, swimming pools or other bodies of

water; always wear shoes, and never allow more than one rider.

WARNING:

FAILURE TO FOLLOW ANY OF THE FOLLOWING SAFETY PRECAUTIONS

CAN AND MAY LEAD TO DAMAGE TO YOUR DEVICE, VOID YOUR

MANUFACTURER WARRANTY, LEAD TO PROPERTY DAMAGE, CAUSE

SERIOUS BODILY INJURY, AND CAN LEAD TO DEATH.

Before using your device, be sure to familiarize yourself with the

operating procedures.

OPERATING YOUR DEVICE

Make sure the device is fully charged before your initial use. For

charging instructions, please follow details under CHARGING YOUR

DEVICE.

Stand directly behind your device and place one foot on the

corresponding foot mat (as described in the diagram below). Keep

your weight on the foot which is still on the ground, otherwise the

device may begin to move or vibrate, making it difficult to step on

evenly with your other foot. When you are ready, shift your weight to

the foot already placed on the device and step on with your second

foot quickly and evenly (as described in the diagram below).

Find your center of gravity. If your weight is distributed correctly on

the foot mats and your center of gravity is level, you should be able

to stand on your device just as if you were standing on the ground.

On average, it takes 3-5 minutes just to get comfortable standing on

your device and maintaining proper balance. Having a spotter will

RIDING YOUR Hover-1 BEAST

Stay relaxed and step on quickly, confidently and

evenly. Imagine climbing stairs, one foot, then the

other. Look up once your feet are even. The Hover-1

Beast may vibrate or spin in one direction, if weight

and pressure are applied to only one foot mat. THIS

IS NORMAL.

NOTES:

help you feel more secure. The Hover-1 Beast is an incredibly intuitive

device; it senses even the slightest bit of motion, so having any

anxiety or reservation about stepping on may cause you to panic

and trigger unwanted movement.

When you first begin using your device, the fastest way to move in

your desired direction is to focus in that direction. You will notice that

just thinking about which way you would like to go will shift your

center of gravity, and that subtle movement will propel you in that

direction.

Your center of gravity determines which direction you move,

accelerate, decelerate, and come to a complete stop. As

described in the diagram below, tilt your center of gravity in the

direction you wish to move.

To turn, focus on the direction you wish to turn and stay relaxed.

As you get comfortable on the device, you will notice it becomes

easier to maneuver. Remember at higher speeds, it is necessary to

shift your weight to overcome the centrifugal force.

Bend your knees if you encounter bumps or uneven surfaces, then

dismount and carry your Hover-1 Beast to a safe operating surface.

Dismounting your device can be one of the easiest steps, yet when

done incorrectly, may cause you to fall. To properly dismount, from a

stopped position, lift one leg up and set your foot back down on the

ground (STEPPING BACK). Then step off completely as described in

the following diagram.

WEIGHT AND SPEED LIMITATIONS

Speed and weight limits are set for your own safety. Please do not

exceed the limits listed here in the manual.

• Maximum Weight: 330 lbs

• Minimum Weight: 44 lbs

• Maximum Speed: Up to 7.45 mph

OPERATING RANGE

The Hover-1 Beast can travel a distance up to 10-11 miles on a fully

charged battery in ideal conditions. The following are some of the

major factors that will affect the operating range of your device.

• Terrain: Riding distance is highest when riding on a smooth, flat

surface. Riding uphill and/or on rough terrain will reduce distance

significantly.

• Weight: A lighter user will have further range than a heavier user.

• Ambient temperature: Please ride and store the device under

recommended temperatures, which will increase driving distance;

battery life, and overall performance of your device.

• Speed and Riding Style: Maintaining a moderate and consistent

speed while riding produces maximum distance. Traveling at high

speeds for extended periods, frequent starts and stops, idling and

frequent acceleration or deceleration will decrease overall distance.

If your Hover-1 Beast is unbalanced, vibrating, or not turning properly,

you can follow the below steps to calibrate it.

• In order for the balance calibration system to work properly, please

place the scooter on a flat, horizontal surface.

• Press and hold the ON/OFF button for a total of 15 seconds. The

scooter will turn on, lighting the battery indicator on the board.

• Turn the board off and then turn the board back on. Press the

power button twice. Calibration will now be completed.